Manuale per l’uso Hoshizaki KM-1800SRH/3

32 pagine 0.84 mb
Scarica

Vai alla pagina of 32

Summary
  • Hoshizaki KM-1800SRH/3 - page 1

    Hoshizaki “A Superior Degree of Reliability” www .hoshizaki.com Models KM-1800SAH/3 KM-1800SWH/3 KM-1800SRH/3 Stackable Crescent Cuber Hoshizaki America, Inc. Issued: 10-2-2000 Revised: 12-11-2006 I N S T R U C T I O N M A N U A L ™ ...

  • Hoshizaki KM-1800SRH/3 - page 2

    2 IMPOR T ANT Only qualified ser vice technicians should attempt to install, ser vice or maintain this icemaker . No installation, ser vice or maintenance should be under taken until the technician has thoroughly read this Instruction Manual. Lik ewise , the owner/manager should not proceed to oper ate the icemak er until the installer has instruc ...

  • Hoshizaki KM-1800SRH/3 - page 3

    3 • Please re vie w this manual. It should be read carefully bef ore the icemak er is installed and operated. Only qualified ser vice technicians should install, ser vice and maintain the icemaker . This manual should be made a v ailab le to the technician prior to installation, maintenance or ser vice. • K eep this manual with the icemaker f ...

  • Hoshizaki KM-1800SRH/3 - page 4

    4 See the nameplate f or electrical and refr igeration specifications . This nameplate is located on the upper right hand side of rear panel. Since this nameplate is located on the rear panel of the icemaker , it cannot be read when the back of the icemak er is against a wall or against another piece of kitchen equipment. Theref ore , the necessar ...

  • Hoshizaki KM-1800SRH/3 - page 5

    5 See the nameplate f or electrical and refr igeration specifications . This nameplate is located on the upper right hand side of rear panel. Since this nameplate is located on the rear panel of the icemaker , it cannot be read when the back of the icemak er is against a wall or against another piece of kitchen equipment. Theref ore , the necessar ...

  • Hoshizaki KM-1800SRH/3 - page 6

    6 See the nameplate f or electrical and refr igeration specifications . This nameplate is located on the upper right hand side of rear panel. Since this nameplate is located on the rear panel of the icemaker , it cannot be read when the back of the icemak er is against a wall or against another piece of kitchen equipment. Theref ore , the necessar ...

  • Hoshizaki KM-1800SRH/3 - page 7

    7 See the nameplate f or electrical and refr igeration specifications . This nameplate is located on the upper right hand side of rear panel. Since this nameplate is located on the rear panel of the icemaker , it cannot be read when the back of the icemak er is against a wall or against another piece of kitchen equipment. Theref ore , the necessar ...

  • Hoshizaki KM-1800SRH/3 - page 8

    8 See the nameplate f or electrical and refr igeration specifications . This nameplate is located on the upper right hand side of rear panel. Since this nameplate is located on the rear panel of the icemaker , it cannot be read when the back of the icemak er is against a wall or against another piece of kitchen equipment. Theref ore , the necessar ...

  • Hoshizaki KM-1800SRH/3 - page 9

    9 See the nameplate f or electrical and refr igeration specifications . This nameplate is located on the upper right hand side of rear panel. Since this nameplate is located on the rear panel of the icemaker , it cannot be read when the back of the icemak er is against a wall or against another piece of kitchen equipment. Theref ore , the necessar ...

  • Hoshizaki KM-1800SRH/3 - page 10

    10 Note: When used with a storage bin not recommended by Hoshizaki, the icemak er needs the space at the bottom opening as in the illustration. Unit: inches (mm) B. Dimensions/Connections 1. KM-1800SAH/3 ...

  • Hoshizaki KM-1800SRH/3 - page 11

    11 Note: When used with a storage bin not recommended by Hoshizaki, the icemak er needs the space at the bottom opening as in the illustration. Unit: inches (mm) 2. KM-1800SWH/3 ...

  • Hoshizaki KM-1800SRH/3 - page 12

    12 3. KM-1800SRH/3 Note: When used with a storage bin not recommended by Hoshizaki, the icemak er needs the space at the bottom opening as in the illustration. Unit: inches (mm) ...

  • Hoshizaki KM-1800SRH/3 - page 13

    13 II. Installation and Operating Instructions A. Checks Bef ore Installation IMPOR T ANT 1. Remov e all shipping car tons, tape and pac king. If packing material is left in the icemaker , it will not work proper ly . 2. Ensure all components, f asteners and thumbscre ws are securely in place. • Remov e the panels to prev ent damage when installi ...

  • Hoshizaki KM-1800SRH/3 - page 14

    14 C. Location W ARNING This icemaker is not intended f or outdoor use. Nor mal operating ambient temperature should be within +45°F to +100°F (+7°C to +38°C); Nor mal operating w ater temperature should be within +45°F to +90°F (+7°C to +32°C). Operation of the icemak er , for e xtended per iods, outside of these normal temperature ranges ...

  • Hoshizaki KM-1800SRH/3 - page 15

    15 CA UTION Bef ore operating the icemak er , the bin control ther mostat assembly must be installed correctly . F ailure to properly install the assembly could result in ice backup and unit damage . 5) Install the bin control ther mostat. a. Remov e the baffle from the bin. b . Remov e the tie secur ing the bin control ther mostat assemb ly . The ...

  • Hoshizaki KM-1800SRH/3 - page 16

    16 If a Hoshizaki B-800, B-900 or B-1150 bin is being used: g. Put aside the "Z" brack et; it is not needed with the bins listed abov e. h. Remov e the two scre ws from the lo wer par t of the ther mostat brac ket (plastic) and use them to attach the ther mostat e xtension brack et (stainless) to the ther mostat brac ket (plastic). Ther m ...

  • Hoshizaki KM-1800SRH/3 - page 17

    17 7) Remov e the ther mostat bulb attachment (plastic) of the upper unit from the thermostat e xtension brac ket (stainless). 8) Carefully remov e the ther mostat bulb from the thermostat bulb attachment (plastic) of the upper unit. 9) Carefully route the ther mostat b ulb and capillar y tubing of the upper unit through the bottom hole of the uppe ...

  • Hoshizaki KM-1800SRH/3 - page 18

    18 Fig. 8b F . Electrical Connection W ARNING 1. Electr ical connection must be made in accordance with the instructions on a "W ARNING" tag, provided with the pig tail leads in the junction bo x. 2. This icemaker requires a ground that meets the national and local electrical code requirements. T o prev ent possible electrical shock to in ...

  • Hoshizaki KM-1800SRH/3 - page 19

    19 G. Installation of Remote Condenser Unit 1. Checks Bef ore Installation 1) Unpack and remo ve shipping car ton, tape(s) and packing. 2) Check that the refrigerant lines do not rub or touch lines or other surf aces , and that the f an b lade tur ns freely . 2. Location The condenser unit must be positioned in a permanent site under the follo wing ...

  • Hoshizaki KM-1800SRH/3 - page 20

    20 3. Setup 1) Secure the legs to the condenser unit with eight M8×16 mm he xagon bolts and M8 nuts as shown in the illustr ation. See Fig. 10. Note: Locate the legs symmetrically . 2) The legs hav e eight mounting holes. Secure the legs with eight bolts (not included). 3) Install enough length of two copper tubings pro vided with P ar k er quick ...

  • Hoshizaki KM-1800SRH/3 - page 21

    21 4. Electrical Connection W ARNING This remote condenser unit requires a ground that meets the national and local electrical code requirements. T o pre v ent possib le electrical shock to individuals or e xtensiv e damage to equipment, install a proper ground wire to this condenser unit. • This condenser unit must be connected to the f an motor ...

  • Hoshizaki KM-1800SRH/3 - page 22

    22 H. W ater Suppl y and Drain Connections See Fig. 14a, 14b and 14c W ARNING T o prev ent damage to the pump assembly , do not operate the icemak er when the water supply is OFF , or if the pressure is below 10 PSIG. Do not run the icemaker until the proper w ater pressure is reached. • W ater supply inlet is 1/2" f emale pipe thread (FPT). ...

  • Hoshizaki KM-1800SRH/3 - page 23

    23 Fig. 14a KM-1800SAH/3 KM-1800SWH/3 Fig. 14b ...

  • Hoshizaki KM-1800SRH/3 - page 24

    24 KM-1800SRH/3 Fig. 14c ...

  • Hoshizaki KM-1800SRH/3 - page 25

    25 I. Final Checklist 1) Is the icemaker le v el? 2) Is the icemaker in a site where the ambient temper ature is within +45°F to +100°F (+7°C to +38°C) all year around? 3) Is there at least a 12" clearance around the icemak er f or maintenance or ser vice? 4) Hav e all shipping tape(s), packing and car tons been remov ed from the icemaker? ...

  • Hoshizaki KM-1800SRH/3 - page 26

    26 J . Star tup CA UTION 1. All par ts are f actor y-adjusted. Improper adjustments ma y result in f ailure. 2. If the unit is tur ned off, w ait for at least 3 minutes bef ore restar ting the icemaker to pre v ent damage to the compressor . 3. Do not operate the unit in the "W ASH" position without water in the water tank. This will caus ...

  • Hoshizaki KM-1800SRH/3 - page 27

    27 III. Cleaning and Maintenance Instructions IMPOR T ANT Ensure all components, f asteners and thumbscrews are securely in place after any maintenance or cleaning is done to the equipment. A. Cleaning Instructions W ARNING 1. HOSHIZAKI recommends cleaning this unit at least once a year . More frequent cleaning, how e v er , ma y be required in som ...

  • Hoshizaki KM-1800SRH/3 - page 28

    28 1. Cleaning Procedure 1) Dilute appro ximately 38 fl. oz. of recommended cleaner Hoshizaki "Scale A wa y" or "LIME-A-W A Y ," (Economics Laborator y , Inc.) with 7 gal. of water . 2) Remov e all ice from the ev aporator and the storage bin. Note: T o remov e cubes on the e v aporator , tur n off the power supply and turn it ...

  • Hoshizaki KM-1800SRH/3 - page 29

    29 24) T ur n on the power supply to rinse off the cleaning solution. 25) T ur n off the power supply after 5 min utes. 26) Remov e the front panel and the insulation panel. 27) Remov e the cap located on the front bottom par t of the ice dropping hole . Drain the water tank. Replace the cap and the insulation panel in their correct positions. Note ...

  • Hoshizaki KM-1800SRH/3 - page 30

    30 2. Storage Bin and Scoop • W ash y our hands bef ore remo ving ice. Use the plastic scoop provided (bin accessory). • The storage bin is f or ice use only . Do not store anything else in the bin. • K eep the scoop clean. Clean it by using a neutr al cleaner and rinse thoroughly . • Clean the bin liner by using a neutr al cleaner . Rinse ...

  • Hoshizaki KM-1800SRH/3 - page 31

    31 2. Remove the water fr om the potable water suppl y line: 1) Remov e the front panel. (Except water-cooled model) 2) Mov e the control switch on the control bo x to the "OFF" position. 3) W ait 3 minutes . 4) Close the potable w ater supply line shut-off valv e and open the potable water supply line drain v alve . See Fig. 14a, 14b , o ...

  • Hoshizaki KM-1800SRH/3 - page 32

    32 HOSHIZAKI AMERICA, INC. 618 Hwy . 74 S., Peachtree City , GA 30269 USA TEL (770) 487-2331 F AX (770) 487-3360 www .hoshizaki.com 91A1SA10D ...

Fabbricante Hoshizaki Categoria Ice Maker

I documenti che otteniamo dal fabbricante del dispositivoHoshizaki KM-1800SRH/3 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Hoshizaki
- manuali per l’uso KM-1800SRH/3
- schede prodotto Hoshizaki
- opuscoli
- o etichette energetiche Hoshizaki KM-1800SRH/3
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Hoshizaki KM-1800SRH/3.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Hoshizaki KM-1800SRH/3, manuali di manutenzione, brevi manuali o manuali utente Hoshizaki KM-1800SRH/3. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Hoshizaki KM-1800SRH/3.

Manuali per l’uso simili

Manuale completo del dispositivo Hoshizaki KM-1800SRH/3, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Hoshizaki KM-1800SRH/3 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Hoshizaki KM-1800SRH/3.

Il manuale per l’uso completo Hoshizaki, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Hoshizaki KM-1800SRH/3 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Hoshizaki KM-1800SRH/3, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Hoshizaki KM-1800SRH/3 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Hoshizaki KM-1800SRH/3 - che ci dovrebbe aiutare nei primi passi durante l'uso Hoshizaki KM-1800SRH/3
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Hoshizaki KM-1800SRH/3
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Hoshizaki KM-1800SRH/3 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Hoshizaki KM-1800SRH/3?

Utilizza il modulo sottostante

Se non hai risolto il problema con Hoshizaki KM-1800SRH/3 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Hoshizaki KM-1800SRH/3 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)