Italiano dropdown-ico

Manuale per l’uso Cisco Systems 3000 Series

30 pagine 0.98 mb
Scarica

Vai alla pagina of 30

Summary
  • Cisco Systems 3000 Series - page 1

    G ETTING S TARTED G UIDE Cisco Catalyst Blade Sw itch 3000 Series for HP Getting Started Guide 1 About This Guide 2 T aking Out What Y ou Need 3 HP Blade System Arc hitecture 4 Installing the Switc h Modul e in the Blade Enclosure 5 Using the Onboard Administrator to Assign an IP Address to the S witc h Module and Running Expr ess Setup 6 Managing ...

  • Cisco Systems 3000 Series - page 2

    2 1 About This Guide This guide provides in structions on how to install your Cisco C atalyst Blade Switch 3120 for HP or Cisco Catalyst Blade Switch 3020 for HP— referred to as the switch module —in the H P c-Class BladeSystem and how to set up and configure your switch module. The HP c-Class BladeS ystem— referred to as the blade enclosure ...

  • Cisco Systems 3000 Series - page 3

    3 2 Taking Out What You Need Follow these steps: 1. Unpack and remove the switch module and the accessory kit from the shipping box. 2. Return the packing material to the shipping contai ner , and save it for future use. 3. V erify that you have received the items shown on page 3. If any item is missing or damaged, contact your Cisco representative ...

  • Cisco Systems 3000 Series - page 4

    4 Cisco Switch Modu le Descriptions These sections describe the switch modules: • Cisco Catalyst Blade Switch 3120 for HP , page 4 • Cisco Catalyst Blade Switch 3020 for HP , page 6 The switch module is powered from the blade encl os ure backplane. The switch module does not have a fan. The blade enclosure provides temperature management. The s ...

  • Cisco Systems 3000 Series - page 5

    5 Figure 1 shows the Cisco Cataly st Blade Switch 3120 for HP switch mo dule. Figure 1 The Catalyst Blade Switc h 3120 for HP 1 Switch module 8 LEDs for ports 19 and 20 2 UID 1 LED 1. UID: unit identifier. 9 Gigabit Ethernet uplink ports 23 to 26 3 Health LEDs 10 Gigabit Ethernet ports 19 and 20 or 10-Gigabit Ethernet slot 1 4 System status LED s 1 ...

  • Cisco Systems 3000 Series - page 6

    6 T able 1 describes the Cisco Catalyst Blade Switch 3120 for HP switch module ports. Each external port has an associated LED. Cisco Catalyst Blade Switch 3020 for HP The Cisco Catalyst Blade Sw itch 3020 for HP is a 24-Gigabit Ethernet port, Layer 2+ switch module. Sixteen of the Gigabit Ethernet ports are internal 1000BASE-X dow nlink port s tha ...

  • Cisco Systems 3000 Series - page 7

    7 Figure 2 shows the Cisco Cataly st Blade Switch 3020 for HP switch mo dule. Each external port has an associated LED. Figure 2 The Catalyst Blade Switc h 3020 for HP 1 Switch module 7 Health LED 2 Release latch 8 LEDs for SFP module ports 17 to 20 3 System status LED s 9 SFP module ports 17 to 20 4 Mode button 10 LEDs for Gigabit Ethernet ports 1 ...

  • Cisco Systems 3000 Series - page 8

    8 T able 2 describes the switch module ports. Ea ch e xternal port has an associated LED. T a ble 2 Cisco Catalyst Bl ade Switc h 3020 for HP P ort Descr iptions Port Description Ports 1 to 16 Internal Gigabit Ethernet 1000BASE-X down link ports. Ports 17 to 20 and Ports 17x to 20x Dual-purpose SFP module/RJ-45 copper Ethernet uplink ports. The SFP ...

  • Cisco Systems 3000 Series - page 9

    9 3 HP Blade System Architecture Figure 3 shows the rear view of the blade enclos ure, in which you install the switch module. Figur e 3 Rear View of the Blade Enclosure 1 Blade enclosure rear view 7 Interconnect module bay 5 2 Blade enclosure fans 8 Interconnect module bay 6 3 Interconnect bay 1 with switch module installed 9 Interconnect module b ...

  • Cisco Systems 3000 Series - page 10

    10 Consider these prerequisites before you install the switch module: • Fill any unoccupied interconnect ba ys or any unoccupied power module bays in the blade enclosure with blanks. • Identify the b ays in which you will insert the switch modules. Plan to install the first switch module in bay 1, the second in bay 2, and so on up to bay 8, if ...

  • Cisco Systems 3000 Series - page 11

    11 Follow these steps to install the switch module in the blade enclosure. The illustrations in this section show the Cisco Catalyst Blade Switch 3020 fo r HP switch module. The instructions are the same for the Cisco Catalyst Blade Switch 3120 for HP sw itch module. Step 1 If you have not already done so, touch the stat ic-protective packa ge that ...

  • Cisco Systems 3000 Series - page 12

    12 Step 4 Ensure that the release latch on the switch module is in the open position (perpendicular to the module) : Step 5 Slide the switch module into the bay until it stops. (See Figure 5.) Figur e 5 Installing the Sw itch M odule int o the Blade Enclosur e Inter connect Module Ba y 1 Switch module release latch 153141 23x 24x 21x 24x 17x 18x 17 ...

  • Cisco Systems 3000 Series - page 13

    13 Step 6 Push the release latch o n the front of the swi tch module to the cl osed position. 5 Using the Onboard Administrato r to Assign an IP Address to the Switch Module and Running Express Setup For the switch module to obtain an IP addres s for the Fa0 interface thro ugh the Onboard Administrator , these conditions must be met: • The blade ...

  • Cisco Systems 3000 Series - page 14

    14 Step 4 Using a PC that is connected to the same ne twork segment as the blade enclosure Onboard Administrator , access the Onboard Administrator in a browser window . Enter your assigned user name and password. Step 5 Choose Enclosure Information > Interconnect Bays to open the Interconnect Bay Summary window where you can find the assigned I ...

  • Cisco Systems 3000 Series - page 15

    15 Figur e 6 Expr ess Setup P age for the Cisco Catalyst Blade Switc h 3120 for HP Figur e 7 Expr ess Setup P age for the Cisco Catalyst Blade Switc h 3020 for HP Step 8 Go to “Using Express Setup” to finish setting up the sw itch module. ...

  • Cisco Systems 3000 Series - page 16

    16 Using Express Setup Before you complete the setup program, obtain the default gateway IP address and the switch password from your system administrator . Depe nding on whether you are running Express Setup on a Cisco Catalyst Blade Switch 3120 for HP sw itch module or a Cisco Catalyst Blade Switch 3020 for HP switch module, you can config ure th ...

  • Cisco Systems 3000 Series - page 17

    17 Figure 8 A dvanced Settings T ab Step 2 In the Host Name field, enter a name for the switch m odule. The host name is limited to 31 characters; embedded spaces are not a llowed. Step 3 In the System Date and System T ime fields, en ter the current date and time, or use the down arrows to select them. Step 4 In the Time Zone field, use the down a ...

  • Cisco Systems 3000 Series - page 18

    18 Step 9 If you enable SNMP , you must enter a community string in the SNMP Read Community field, the SNMP W rite Community field, or bo th. SNMP community strings authenticate access to MIB objects. Embedded spaces are not allowed in SNMP co mmunity strings. When you set the SNMP read community , you can acc ess SNMP information, but you cannot m ...

  • Cisco Systems 3000 Series - page 19

    19 Step 6 Enter end . Step 7 Enter copy running-configuratio n startup-configuration to save this setting. Step 8 At the prompt, press Return . Step 9 T o veri fy that this switch is se t as the stack master , enter th e show sw itch user EXEC command. For more information about creating switch stacks , see the “Planning and Creating a Switch Sta ...

  • Cisco Systems 3000 Series - page 20

    20 Figure 9 Device Manager P age for the Ci sco Catalyst Blade Switc h 3120 for HP ...

  • Cisco Systems 3000 Series - page 21

    21 Figure 1 0 Device Manager P age f or the Cisco Catalyst Blade Switc h 3020 for HP Step 3 Use the device manager to perform basic switch module configuration and monitori ng. See the device manager online help for more information. Step 4 For more advanced configuration, download and run the Cisco Network Assistant, which is described in the next ...

  • Cisco Systems 3000 Series - page 22

    22 Step 3 Configure the PC terminal emulation so ftware for: – 9600 baud – 8 data bits – No parity – 1 stop bit – No flow control Step 4 Use the CLI to enter commands to config ure the switch module. See the software configuration guide and the command reference for more information. Using the Onboard Administrator CLI See the HP BladeSys ...

  • Cisco Systems 3000 Series - page 23

    23 7 Planning and Creating a Switch Stack (Only the Cisco Catalyst Blade Switch 3120 for HP) A switch stack is a set of up to nine stacking-capab le switch modules that are connected through their StackWise Plus ports. One of the switches controls the operation of the stack an d is called the stack master . The stack master and the other switches i ...

  • Cisco Systems 3000 Series - page 24

    24 – CAB-STK-E-0.5M= (0.5-meter cable) – CAB-STK-E-1M= (1-meter cable) – CAB-STK-E-3M= (3-meter cable) For switch module dimensions and additiona l stacking guidelines, see the switch module ha rdware installation guide. For concepts and procedures to manage switch stacks , see the switch module software confi guration guide an d the stack co ...

  • Cisco Systems 3000 Series - page 25

    25 Step 3 Insert the cable into the Stac kWise Plus port on the front panel of the switch. Insert the other end of the cable into the connector of the other switch. Always use a Cisco-approved StackWise Plus cable to connect the switches. Figure 1 1 Inserting the StackWise Plus Cables When you remove the StackWise Plus cables from the connec tors, ...

  • Cisco Systems 3000 Series - page 26

    26 The autonegotiation feature is enabled by defaul t on the switch. At this setting, the switch module ports configure themselves to operate at the speed of atta ched devices. If the attached de vice does not support autonegotiation, you can explici tly set the switch module port speed and the duplex parameters. T o maximize performanc e, either a ...

  • Cisco Systems 3000 Series - page 27

    27 Verify Port Connectivity After you connect a device to the switch module port, the port LED turns am ber while the switch module establishes a link. This process takes about 30 secon ds. Then the LED turns green when the switch module and the at tached device have an estab lished link. If the LED is off, the device might not be turned on, there ...

  • Cisco Systems 3000 Series - page 28

    28 Accessing Help Online First look for a solution to your problem in the tr oubleshooting section of the hardware installation guide or software configuration guide for your swit ch module on Cisco.com. Y ou can also access the Cisco T echnical Support and Documentation w ebsite for a list of known hardware p roblems and extensive troubleshooting ...

  • Cisco Systems 3000 Series - page 29

    29 10 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitti ng a service request, and gathering additional information, see the monthly What’ s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation, at: http://www .cisco.com/en/US/docs/genera ...

  • Cisco Systems 3000 Series - page 30

    Americas Headquarters Cisco Systems, I nc. 170 W est T asman Drive San Jose, CA 95134- 1706 USA www .cisco. com T el: 408 5 26-4000 800 553-NETS (6387) Fax: 408 527-0883 Asia Pacific Headquarters Cisco Systems, In c. 168 Robinson Road #28-01 Capital T ower Singapore 068912 www .cisco. com T el: +65 6 317 7777 Fax: +65 6317 7799 Europe Headquarters ...

Fabbricante Cisco Systems Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoCisco Systems 3000 Series possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cisco Systems
- manuali per l’uso 3000 Series
- schede prodotto Cisco Systems
- opuscoli
- o etichette energetiche Cisco Systems 3000 Series
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cisco Systems 3000 Series.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cisco Systems 3000 Series, manuali di manutenzione, brevi manuali o manuali utente Cisco Systems 3000 Series. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cisco Systems 3000 Series.

Manuali per l’uso simili

Manuale completo del dispositivo Cisco Systems 3000 Series, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cisco Systems 3000 Series dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cisco Systems 3000 Series.

Il manuale per l’uso completo Cisco Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cisco Systems 3000 Series - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cisco Systems 3000 Series, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cisco Systems 3000 Series che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cisco Systems 3000 Series - che ci dovrebbe aiutare nei primi passi durante l'uso Cisco Systems 3000 Series
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cisco Systems 3000 Series
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cisco Systems 3000 Series in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cisco Systems 3000 Series?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cisco Systems 3000 Series con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco Systems 3000 Series è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)