Italiano dropdown-ico

Manuale per l’uso AMX R-3

34 pagine 1.22 mb
Scarica

Vai alla pagina of 34

Summary
  • AMX R-3 - page 1

    Operation/Reference Guide Mio Remote Controls Mio Modero ® R-3 Remote Control Device Last Updated: 1/29/200 8 ...

  • AMX R-3 - page 2

    AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under n ormal use for three (3) years from the date of purchase fr om AMX, with the following exceptions: • Electroluminescent and LCD Control P ane ls are warranted for three (3) years, except for the display and touch overlay componen ...

  • AMX R-3 - page 3

    Table of Contents i Mio Modero R-3 Rem ote Table of Contents Overview ...................... ...................................................................... ................ 1 The Mio Modero® R-3 ......................... ........................ .................... ......................... 1 Touch And T ilt Sensor ... ............. ..... ...

  • AMX R-3 - page 4

    ii Mio Moder o R-3 Remote Table of Contents ...

  • AMX R-3 - page 5

    Overview 1 Mio Moder o R-3 Remote Overview The Mio Modero ® R-3 The Mio Modero ® R-3 remote provides custom control features, contained in an elegant handheld rechargeable de vice. The Mio R-3 co mmunicates with a NetLinx ® ma ster via a wireless Zigbee® network. Selecting a source device sends a command to the master and runs predetermined e v ...

  • AMX R-3 - page 6

    Overview 2 Mio Modero R-3 Remote Touch And Tilt Sensor The Mio R-3 wakes up upon touching either the chrome side rails or pressing a button. When the remote times out while holding it, you can reaw aken the de vice by tilting it. Errant jostling, such as a b umped table, will not wake the device unless you are actually holding it. Specific ations T ...

  • AMX R-3 - page 7

    Overview 3 Mio Moder o R-3 Remote FCC Compliance This radio module was tested and certif ied as a stand-alone device according to FCC Rules CFR 47, Part 15, Subpart C. If this device is installed in a manner such that the radio module FCC ID. la bel is not visible on the outside of the end product, a label must be placed on the end product with the ...

  • AMX R-3 - page 8

    Overview 4 Mio Modero R-3 Remote ...

  • AMX R-3 - page 9

    Mio Modero R-3 Setup 5 Mio Moder o R-3 Remote Mio Modero R-3 Setup Inserting or Replacing the Li thium-ion Battery for the Mio R-3 The Mio Modero R-3 comes with a rechargeable Lithiu m-Ion battery that needs to be installed before use. T o install your Lithium-Ion ba ttery into the device: 1. Flip and turn the Mio R-3 de vice so that the buttons ar ...

  • AMX R-3 - page 10

    Mio Modero R-3 Setup 6 Mio Modero R-3 Remote Installing Custom Buttons 1. Flip and turn the Mio R-3 de vice so that the buttons are facing aw ay from you and the device is upside down. 2. Holding the Mio R-3 in both hands, place your thumbs on the battery door and push up to slide the battery door free. The battery door will slide in the direction ...

  • AMX R-3 - page 11

    Setup Mode 7 Mio Modero R-3 Remote Setup Mode The Setup mode allows you to set the following de vice features on the Mio R-3:  T ransmit Mode  T imeout Adjustment  Download Mode  Debug Mode  Firmware V ersion  Device ID  LED A wake Brightness  LED Sleep Brightness  ZigBee ID P AN , Channel, and System Conne ction  Site ...

  • AMX R-3 - page 12

    Setup Mode 8 Mio Modero R-3 Remote Download Mode In order to do wnload new f irmware or a new conf iguration or font file to the Mio R-3 remote using the remote's program port (see Using the Pr ogr amming Jac k on The Mio R-3 section on pag e 11 for de tails), the remote must first be placed into Download mode. Press 3 on the remote to toggle ...

  • AMX R-3 - page 13

    Setup Mode 9 Mio Modero R-3 Remote LED Sleep Mode Brightness The red LEDs that backlight the Po wer button when the remote is awak e are also used to indicate charging status. These LEDs will slo wly blink on and of f if the remote is place in the char ging cradle and the Lithium-Ion battery pack is being charged. The LEDs will remain on when charg ...

  • AMX R-3 - page 14

    Setup Mode 10 Mio Modero R-3 Remote ...

  • AMX R-3 - page 15

    Programming The Mio R-3 11 Mio Modero R-3 Remote Programming The Mio R-3 Most functionality of the Mio R-3 is handled using the Ke ypadBuilder application. Go to www .amx.com for the K e ypadBuilder Instruction Manual . The Mio R-3 recognizes a select number o f Serial Commands. For a full list and descriptions, consult the Serial Commands section ...

  • AMX R-3 - page 16

    Programming The Mio R-3 12 Mio Modero R-3 Remote Updating Mio R-3 Firmware Updating firmware in the Mio R-3 is also done through the programming jac k. T o update the main firmw are for the Mio R-3: 1. Connect the Mio R-3 to your computer via the programming jack (FIG. 4). 2. Put the device into Dow nload mode, as sho wn on page 8. 3. Open NetLinx ...

  • AMX R-3 - page 17

    Programming The Mio R-3 13 Mio Modero R-3 Remote Channel Codes The following table gi ves the channel codes associated with each button on the Mio R-3. Thirty-six of the buttons change channel codes based on what b utton was last pressed. Nine of the b uttons always emit the same channel code regardless of what b utton was last pressed. The Mio R3 ...

  • AMX R-3 - page 18

    Programming The Mio R-3 14 Mio Modero R-3 Remote Channel Codes (Cont.) B ut t o n Dev 1 D ev 2 D ev 3 D ev 4 D ev 5 D ev 6 Up 32 72 1 12 152 192 232 Down 33 73 1 13 153 193 233 Left 34 74 1 14 154 194 234 Right 35 75 1 15 155 195 235 SELECT 36 76 1 16 156 196 236 EXIT 37 77 1 17 157 197 237 GUIDE 38 78 1 18 158 198 238 INFO 39 79 1 19 159 199 239 L ...

  • AMX R-3 - page 19

    Programming The Mio R-3 15 Mio Modero R-3 Remote Serial Commands The Mio R-3 remote supports a few commands that can be uploaded to the device using a terminal program such as HyperT erminal. These comman ds ar e not needed for normal usage or programming of the remote. Serial Commands @BRT Set Brightness level This command can be used to customize ...

  • AMX R-3 - page 20

    Programming The Mio R-3 16 Mio Modero R-3 Remote Serial Commands (Cont.) ^FML ^FML S Sets a line of the display to a menu line Syntax: "'^FML-<variable text address range>,S'" V ariables: • variable text address range = 1; th e address range corresponds to the dynamic line number-o nly one line is supported on this devic ...

  • AMX R-3 - page 21

    Programming The Mio R-3 17 Mio Modero R-3 Remote Serial Commands (Cont.) IRMODE # Sets the IR transmission frequency to either 38 or 455KHz Syntax: IRMODE # V ariables: • < mode> = 38 - IR only , 38KHz 455 - IR only , 455KHz ZIG - ZigBee only ZIG38 - ZigBee + IR 38KHz ZIG455 - ZigBee + IR 455KHz Example: IRMODE 455 Sets the IR transmission ...

  • AMX R-3 - page 22

    Programming The Mio R-3 18 Mio Modero R-3 Remote Serial Commands (Cont.) REVD # Reverse the image on the LCD Syntax: REVD # V ariables: • # = (1 = R everse video, 0 = Normal Video) Example: REVD 1 Reverses the image on the LCD; pixels pr eviously lit go off; pixels previously off, come on. SETD Sets the ICSP Device Number Syntax: SETD <deviceN ...

  • AMX R-3 - page 23

    Programming The Mio R-3 19 Mio Modero R-3 Remote Serial Commands (Cont.) @SST Sends a string to the master upon startup Syntax: "'@SST-<new text>'" V ariables: • new te xt = 1 - 20 ASCII characters. Default string is ST ARTUP . Example: SEND_COMMANDPanel,"'@SST-Panel Start'" Sends the string " Pa ...

  • AMX R-3 - page 24

    Programming The Mio R-3 20 Mio Modero R-3 Remote Serial Commands (Cont.) ZAP! Erase Configuration Information in Flash Memory Syntax: ZAP! t V ariables: • t = MENU or FONT or blank Example: ZAP! Clears all configuration information and erases the font. The text displayed on the LCD for the six devices returns to default and all parameters that ca ...

  • AMX R-3 - page 25

    Programming The Mio R-3 21 Mio Modero R-3 Remote Send_Commands When used with ZigBee communications and a NetL inx master , the Mio R-3 supports a small set of Send_Commands. The table below captures all Send_Commands supported by the Mio R3 Send_Commands @BRT Set Brightness level This command can be used to customize the bright ness of the red LED ...

  • AMX R-3 - page 26

    Programming The Mio R-3 22 Mio Modero R-3 Remote Send_Commands (Cont.) ^FML ^FML S Sets a line of the display to a menu line Syntax: "'^FML-<variable text address range>,S'" V ariables: • variable text address range = 1; th e address range corresponds to the dynamic line number-o nly one line is supported on this device. ...

  • AMX R-3 - page 27

    Programming The Mio R-3 23 Mio Modero R-3 Remote Send_Commands (Cont.) ^JST Set text alignment using a numeric keypad layout for those buttons with a defined address range Syntax: '^JST-<variable text address range>,<new text alignment>'" V ariable: • variable text address range = 1; th e address range corresponds to th ...

  • AMX R-3 - page 28

    Programming The Mio R-3 24 Mio Modero R-3 Remote Send_Commands (Cont.) SLEEP Set the Sleep timer or put the remote to sleep immediately . This command can be used if a sleep time ot her than 3, 6, 9, or 12 seconds is desired. Syntax: SLEEP Forces keypad to turn backlight off. SLEEP-# Sets sleep time. V ariables: • # = 0 - 60 in seconds; time to w ...

  • AMX R-3 - page 29

    Programming The Mio R-3 25 Mio Modero R-3 Remote Send_Commands (Cont.) ^TXT Assign a text string to those buttons with a defined address range Sets non-unicode text. Syntax: SEND_COMMAND <DEV>,"'^TXT-<vt addr range>,<button states range>,<new text>'" V ariables: • variable text address range = 1. • bu ...

  • AMX R-3 - page 30

    Programming The Mio R-3 26 Mio Modero R-3 Remote ...

  • AMX R-3 - page 31

    Mio Remote Charging Base 27 Mio Moder o R-3 Remote Mio Remote Charging Base The Mio remotes are complemented with a Mio-RCC charging base ( FG147-02) . Specifications FIG. 6 Mio-RCC Charging Base FIG. 7 Mio Remote Charging Bas e (Top and Bottom view ) Rubber feet Angle barrel power connector Charging conta cts (Bottom View) (T op Vie w) ...

  • AMX R-3 - page 32

    Mio Remote Charging Base 28 Mio Modero R-3 Remote The specifications for the Mio remote char ging base and kit are as follo ws: Charging The Mio Remote with Charging Base The Mio remotes receiv e power for charging from a char ging base. 1. Connect the terminal e nd of the power supply to the bottom external power port on the Mio remote charging ba ...

  • AMX R-3 - page 33

    Mio Remote Charging Base 29 M io Modero R-3 R emote ...

  • AMX R-3 - page 34

    1/08 © 2007 AMX. Al l rights reserved. AMX a nd the AMX logo a re register ed trademarks of AM X. AMX reserves the right to alter specific ations without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support ? ...

Fabbricante AMX Categoria Universal Remote

I documenti che otteniamo dal fabbricante del dispositivoAMX R-3 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici AMX
- manuali per l’uso R-3
- schede prodotto AMX
- opuscoli
- o etichette energetiche AMX R-3
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso AMX R-3.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione AMX R-3, manuali di manutenzione, brevi manuali o manuali utente AMX R-3. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto AMX R-3.

Manuali per l’uso simili

Manuale completo del dispositivo AMX R-3, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare AMX R-3 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti AMX R-3.

Il manuale per l’uso completo AMX, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale AMX R-3 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice AMX R-3, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per AMX R-3 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo AMX R-3 - che ci dovrebbe aiutare nei primi passi durante l'uso AMX R-3
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del AMX R-3
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio AMX R-3 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su AMX R-3?

Utilizza il modulo sottostante

Se non hai risolto il problema con AMX R-3 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con AMX R-3 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)