-
Jura Capresso F70 - page 1
IMPRESSA F70/F707 Instructions for use 9/06 Art. Nr. 66380 ...
-
Jura Capresso F70 - page 2
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.com ...
-
Jura Capresso F70 - page 3
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 6 Fig. 7 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 16 Fig. 5 Fig. 8 Fig. 15 Fig. 17 Fig. 18 ...
-
Jura Capresso F70 - page 4
Temp. max. Fig. 19 Fig. 21 Fig. 20 Temp. min. ...
-
Jura Capresso F70 - page 5
Control elements 1. Rotary Switch 2. Illuminated ring 3. ON / OFF symbol 4. 1 LARGE CUP symbol 5. 1 COFFEE symbol 6. 1 ESPRESSO symbol 7. MAINTENANCE symbol 8. START symbol 9. Display dialog system 10. Water tank with handle 11. Filler funnel for pre-ground coffee 12. Bean tank cover 13. Aroma preservation cover 14. Steam / hot water draw-off tap 1 ...
-
Jura Capresso F70 - page 6
6 Contents 1. Safety information .......................................... page 7 1.1 Warning .............................................. page 7 1.2 Precautions .......................................... page 7 2. Preparing the IMPRESSA ................................ page 7 2.1 Check supply voltage .............................. page 7 2.2 Ch ...
-
Jura Capresso F70 - page 7
7 Introduction Thank you for purchasing the IMPRESSA. To ensure perfect func- tioning of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or if you encounter particular problems not specified in these operating instructions in sufficient detail, either contact us directly or cont ...
-
Jura Capresso F70 - page 8
8 Then fill the water tank and reinstall it. Make sure to install the tank properly, it must engage audibly. 2.4 Fill coffee beans To ensure that your machine will work perfectly for a long time and to avoid damage, please note that the grinding gear of your JURA coffee machine is not suitable for coffee beans which were treated, during or afte ...
-
Jura Capresso F70 - page 9
9 CLOSE TAP Close the steam / hot water draw-off tap (14). FILLING SYSTEM HEATING PRESS MAINT. Touch the symbol (7). Machine carries out a rinsing operation. RINSING READY If BEANS FILL is displayed, press the coffee draw-off key again. Machine not filled with coffee beans yet. To get an excellent crema, adjust t ...
-
Jura Capresso F70 - page 10
10 5. Installation of CLARIS plus filter cartridges If the CLARIS plus filter cartridge is installed properly, de-scaling of the coffee machine is no longer required. For more information on the CLARIS plus filter cartridge refer to brochure «CLARIS plus. Hard on limescale. Gentle on your coffee machine.» 5.1 Installing the filter Draw off 1/2 li ...
-
Jura Capresso F70 - page 11
11 Fill the water tank with cold, fresh tap water and reinstall it. Place a sufficiently large receptacle (at least 1/2 litre) under the Professional Cappuccino Frother (15) (Fig. 10). Turn the selector switch of the Professional Cappuccino Frother (15) to the steam position (Fig. 20). Open the tap for dispensing steam/hot water (14 ...
-
Jura Capresso F70 - page 12
12 e.g. 120 ML COFFEE Your coffee is being prepared. READY 9. Making 2 cups of coffee You cannot choose the strength of the coffee when making 2 cups. The machine automatically makes 2 mild cups of coffee. You can set the amount of water you want with the Rotary Switch (1) prior to drawing off coffee Touch the (8) symbol to stop dra ...
-
Jura Capresso F70 - page 13
13 Your coffee is being prepared. READY 10. Drawing off pre-ground coffee Never use instant coffee or quick-coffee. We recommend that you always use powder from fresh coffee beans or, pre- ground, vacuum-packed coffee. Never fill in more than 2 portions of powder. The pre-ground coffee tank is no storage tank. Make sure that the pre-ground ...
-
Jura Capresso F70 - page 14
14 If the required water quantity is reached, the following message is displayed: CLOSE TAP Close the steam / hot water draw-off tap (14). READY Before CLOSE TAP water may still escape the system. 12. Dispensing steam The steam function is used for the preparation of milk foam and hot milk, as well as for the Professional Cappuccino ...
-
Jura Capresso F70 - page 15
15 When using for the first time, remove the protective cover from the Professional Cappuccino Frother (15) (Fig. 6). The protective cover is used only during transport as protection to prevent the ingress of contaminated materials. Remove the milk pipe from the Welcome Pack and connect it to the Professional Cappuccino Frother (15). In ...
-
Jura Capresso F70 - page 16
16 13.3 Rinsing the Professional Cappuccino Frother Carefully pull off the Professional Cappuccino Frother from your IMPRESSA. Dismantle the Professional Cappuccino Frother (15) into its indi- vidual parts (Fig. 16). Thoroughly rinse all parts of the nozzle under running water. Reassemble the Professional Cappuccino Frother (15) and ...
-
Jura Capresso F70 - page 17
17 15. Programming When your IMPRESSA leaves the factory it is adjusted such that you can draw off coffee without having to change any settings. However, you can programme various parameters individually. You can programme the following stages: Filter Water hardness Maintenance Aroma Temperature Time Automatic switch-on ...
-
Jura Capresso F70 - page 18
18 Press the Rotary Switch (1). INTENSIVE Turn the Rotary Switch (1) until the following message is dis- played: STANDARD Press the Rotary Switch (1) to save the setting. AROMA Turn the Rotary Switch (1) until EXIT appears Press the Rotary Switch (1) to leave the programming mode. READY 15.5 Programming the tempe ...
-
Jura Capresso F70 - page 19
19 15.7 Programming the automatic switch-on time You must programme the time (Chapter 15.6) if you want to use the automatic switch-on function (––:–– = inactive). READY Press the Rotary Switch (1) until FILTER – / appears The illuminated ring (2) is active. Turn the Rotary Switch (1) until MACHINE ON is displayed. ...
-
Jura Capresso F70 - page 20
20 READY Press the Rotary Switch (1) until FILTER – / appears The illuminated ring (2) is active. Turn the Rotary Switch (1) until CUPS MADE appears Press the Rotary Switch (1) 100 Press one of the draw-off keys / / to check the number of individual cups made. E.g press draw-off key 1 cup of coffee (5). 20 ...
-
Jura Capresso F70 - page 21
21 Turn the Rotary Switch (1) until EXIT appears Press the Rotary Switch (1) to leave the programming mode. READY 15.12 Programming the display for ML/OZ READY Press the Rotary Switch (1) until FILTER – / appears The illuminated ring (2) is active. Turn the Rotary Switch (1) until DISPLAY appears Press the Rota ...
-
Jura Capresso F70 - page 22
22 The red water level indicator appears when the drip tray (20) is full. 16.3 Drip tray missing NO TRAY If this information is displayed, the drip tray (20) is not installed properly or was not installed at all. Insert the drip tray (20). READY 16.4 Fill coffee beans FILL BEANS Refill beans as described in Chapter 2.4. The ...
-
Jura Capresso F70 - page 23
23 If the water tank shows signs of scaling, remove the scaling using a commercial de-scaling agent. Take out the water tank (Fig. 4). Remove the CLARIS plus filter cartridge, if installed, before de-scaling the water tank. 16.9 Emptying the system Precondition: IMPRESSA switched off This operation is required to protect the IMPRESSA against frost ...
-
Jura Capresso F70 - page 24
24 NO TRAY READY Wipe coffee powder tank with a dry cloth after the cleaning program has finished. The cleaning operation was completed successfully. 17.1 Cleaning without display request Press the Rotary Switch (1) until FILTER – / appears. Turn the Rotary Switch (1) until MAINTENANCE appears. Press the Rotary Swi ...
-
Jura Capresso F70 - page 25
25 Place a receptacle under the hot water spout (Fig. 18). Open the steam / hot water draw-off valve (14) (Fig. 12). DE-SCALING CLOSE TAP Close the steam / hot water draw-off tap (14). DE-SCALING EMPTY TRAY Empty the tray (20). NO TRAY Insert the tray (20) again. FILL WATER Rinse the water tank thoroughly ...
-
Jura Capresso F70 - page 26
26 20. Tips for perfect coffee Height-adjustable coffee spout (17) You can adjust the height of the coffee spout to the size of your cups (Fig. 3) Grinding degree Refer to Chapter 2.5 «Adjusting the grinding gear». Preheating cups You can preheat the cups using hot water or steam. The smaller the coffee you want to draw off, the more important pr ...
-
Jura Capresso F70 - page 27
27 21. Messages Cause Remedy FILL WATER Water tank is empty. Refill water Float defective Rinse or de-scale water tank FILL BEANS Bean tank is empty. Refill beans Although you have refilled beans, the Draw off a cup of coffee. The message will message still appears. disappear only after you have drawn off a cup of coffee EMPTY GROUNDS Coffee ground ...
-
Jura Capresso F70 - page 28
28 22. Problems Problem Cause Remedy Very loud noise coming from the Foreign body in grinding gear Drawing off pre-ground coffee still possible grinding gear Have IMPRESSA checked by JURA Service Too little foam when Professional Cappuccino Frother has Clean the Professional Cappuccino Frother frothing the milk become dirty (Chapter 13) Individual ...
-
Jura Capresso F70 - page 29
29 23. Legal information These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. ...
Hai una domanda su Jura Capresso F70?
Utilizza il modulo sottostante
Se non hai risolto il problema con Jura Capresso F70 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Jura Capresso F70 è probabile che voglia condividere il modo di risolverlo.