Italiano dropdown-ico

Manuale per l’uso Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA

24 pagine 1.3 mb
Scarica

Vai alla pagina of 24

Summary
  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 1

    58TMA Downflow/Horizontal 2-Speed, 2-Stage, Induced-Combustion Gas Furnace Installation, Start-Up, and Operating Instructions Sizes 065-125, Series 111 NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. Index Page SAFETY CONSIDERATIONS ................................. ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 2

    ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS PROCEDURE Electrostatic discharge can affect electronic components. Take precautions during furnace installation and servicing to protect the furnace electronic control. Precautions will pre- vent electrostatic discharges from personnel and hand tools which are held during the procedure. These precautions w ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 3

    in alcoves, attics, crawlspaces, basements, closets, or utility rooms. The design of this furnace line is not A.G.A./C.G.A. certified for installation in mobile homes, recreation vehicles, or outdoors. Before installing the furnace, refer to the current edition of the NFGC and the NFPA 90B. Canadian installations must be installed in accordance NSC ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 4

    Improper installation, adjustment, alteration, service, mainte- nance, or use can cause carbon monoxide poisoning, explo- sion, fire, electrical shock, or other conditions which may cause personal injury, loss of life, or property damage. Consult a qualified installer, service agency, local gas sup- plier, or your distributor or branch for informat ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 5

    installed in that space. A confined space MUST have provisions for supplying air for combustion, ventilation, and dilution of flue gases using 1 of the following methods. (See Fig. 3 and Table 2.) NOTE: In determining free area of an opening, the blocking effect of louvers, grilles, and screens must be considered. If free area of louver or grille d ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 6

    KGASB0201ALL is used. Manufacturer’s accessory floor base is not required when this furnace is installed on manufacturer’s Coil Assembly Part No. CD5 or CK5, or Coil Box Part No. KCAKC is used. 1. Determine application being installed from Table 3. 2. Construct hole in floor per dimensions specified in Table 3 and Fig. 5. 3. Construct plenum to ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 7

    2. When completed, downflow subbase, plenum, and furnace (or coil casing when used) should be installed as shown in Fig. 6. Step 4—Horizontal Attic Installation Do not install furnace on its back; safety control operation will be adversely affected. Never connect return-air ducts to the sides or back of the furnace. A failure to follow this warni ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 8

    → Fig. 9—Horizontal Crawlspace Installation on Hanger Rods A96633 NOTES: ANGLE IRON OR EQUIVALENT ROD LOCATION USING DIMPLE LOCATORS (SEE DIMENSIONAL DWG FOR LOCATIONS) 3 ⁄ 8 -IN. ROD 1. A 1 In. clearance minimum between top of furnace and combustible material.  2. The entire length of furnace must be supported when ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 9

    If flexible connector is required or allowed by authority having jurisdiction, black iron pipe shall be installed at gas valve and extend a minimum of 2 in. outside furnace casing. Use the proper length of pipes to avoid stress on gas control manifold. A failure to follow this warning could result in a gas leak causing fire, explosion, personal inj ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 10

    Step 8—Electrical Connections 115-V WIRING Refer to unit rating plate or Table 6 for equipment electrical requirements. The control system requires an earth ground for proper operation. Do not connect aluminum wire between disconnect switch and furnace. Use only copper wire. Make all electrical connections in accordance with the current edition o ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 11

    This furnace can be installed with either single-stage heating or 2-stage heating thermostat. For single-stage thermostats, connect thermostat W to W/W1 at furnace control terminal block. (See Fig. 15.) For single-stage thermostats the control determines, based on length of previous heating on and off cycles, when to operate in low- and high-gas he ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 12

    his furnace is equipped with 2 manual reset limit switches in gas control area. The switches will open and shut off power to gas valve if a flame rollout or an overheating condition occurs in gas control area. DO NOT bypass switches. Correct inadequate combustion air supply, component failure, re- stricted flue gas passageway before resetting switc ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 13

    → Fig. 18—Unit Wiring Diagram A97508 LEGEND ALS1 AUXILIARY LI MIT SWITCH, OVERTEMP. MANUAL RES ET, SPST (N. C.) ALS2 AUXILIARY LI MIT SWITCH, OVERTEMP. AUTO RESET, SPST (N.C. ) BHI / LOR BL OWER MOTOR SPEED CHANG E RELAY, SPDT BHT / CLR BLOWER MOTOR SPEED CHANGE RELAY , SPDT BLWM BLOWER MOTOR, 4 or 5 -S PEED, PERMANEN T-SPLIT-CAPAC ITOR BLWR BL ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 14

    The furnace starts up in either low- or high-gas heat. If furnace starts up in low-gas heat, control CPU determines low-gas heat on time (from 0 to 16 minutes) which is permitted before switching to high-gas heat. If power is interrupted, stored history is erased, and control CPU selects low-gas heat for up to 16 minutes and then switches to high-g ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 15

    (1.) The thermostat closes R to G-and-Y circuits. The R-Y circuit starts outdoor unit, and R to G-and-Y circuits start furnace blower motor BLWM on high- cool speed. (2.) The EAC terminals EAC-1 and EAC-2 are energized with 115v when blower motor BLWM is operating. (3.) When thermostat is satisfied, R to G-and-Y circuits are opened. The outdoor uni ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 16

    BLWM operation at heat pump heating speed until end of prepurge period, then shuts off until end of HSI ignitor on period (22 sec). b. When installed with a heat pump, furnace control CPU automatically holds blower off time to 22 sec during HSI ignitor on period. After 17 sec of HSI ignitor on period, a trial-for-ignition sequence occurs as describ ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 17

    e. Move setup switch SW-2 to OFF position after completing low-heat adjustment. f. Jumper R and W2 thermostat connections on control center. (See Fig. 14.) This keeps furnace locked in high-heat operation. g. Turn high-heat adjusting screw (5/64 hex Allen wrench) counterclockwise (out) to decrease input rate or clockwise (in) to increase rate. NOTE ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 18

    Table 10—Model 58TMA Orifice Size and Manifold Pressure for Correct Input (Tabulated Data Based on 21,000 Btuh High Heat/13,500 Btuh Low Heat per Burner, Derated 4% for Each 1000 Ft Above Sea Level)* ALTITUDE RANGE (FT) AVG GAS HEAT VALUE AT ALTITUDE (BTU/CU FT) SPECIFIC GRAVITY OF NATURAL GAS 0.58 0.60 0.62 0.64 0.66 Orifice No. Manifold Pressur ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 19

    Table 10—Model 58TMA Orifice Size and Manifold Pressure for Correct Input—Continued (TABULATED DATA BASED ON 21,000 BTUH HIGH HEAT/13,500 BTUH LOW HEAT PER BURNER, DERATED 4% FOR EACH 1000 FT ABOVE SEA LEVEL)* ALTITUDE RANGE (FT) AVG GAS HEAT VALUE AT ALTITUDE (BTU/CU FT) SPECIFIC GRAVITY OF NATURAL GAS 0.58 0.60 0.62 0.64 0.66 Orifice No. Mani ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 20

    Table 10—Model 58TMA Orifice Size and Manifold Pressure for Correct Input—Continued (TABULATED DATA BASED ON 21,000 BTUH HIGH HEAT/13,500 BTUH LOW HEAT PER BURNER, DERATED 4% FOR EACH 1000 FT ABOVE SEA LEVEL)* ALTITUDE RANGE (FT) AVG GAS HEAT VALUE AT ALTITUDE (BTU/CU FT) SPECIFIC GRAVITY OF NATURAL GAS 0.58 0.60 0.62 0.64 0.66 Orifice No. Mani ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 21

    a. Place duct thermometers in return and supply ducts as near furnace as possible. Be sure thermometers do not see heat exchangers so that radiant heat will not affect thermometer readings. This is particularly important with straight-run ducts. b. When thermometer readings stabilize, subtract return-air temperature from supply-air temperature to d ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 22

    components in R-W/W1 circuit. Accurate amp draw read- ings can be obtained at wires normally connected to thermostat subbase terminals R and W/W1. Fig. 21 illus- trates an easy method of obtaining actual amp draw. The amp reading should be taken after blower motor has started and furnace is operating in low heat. To operate furnace in low heat, fir ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 23

    CHECKLIST 1. Put away tools and instruments, and clean up debris. 2. Check SW-1 through SW-4 after completing installation to ensure desired settings for thermostat type (SW-1 and SW-2) and blower off delay (SW-3 and SW-4). Refer to Tables 6 and 7. 3. Verify manual reset switches have continuity. 4. Ensure blower and gas control access doors are pr ...

  • Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - page 24

    A94328 SER VICE TRAINING P ackaged Service T raining prog rams are an e xcellent wa y to increase your knowledge of the equipment discussed in this man ual, including: • Unit F amiliarization • Maintenance • Installation Ov er vie w • Operating Sequence A large selection of product, theor y , and skills prog rams is av ailable , using popul ...

Fabbricante Carrier Categoria Furnace

I documenti che otteniamo dal fabbricante del dispositivoCarrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Carrier
- manuali per l’uso DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA
- schede prodotto Carrier
- opuscoli
- o etichette energetiche Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA, manuali di manutenzione, brevi manuali o manuali utente Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA.

Manuali per l’uso simili

Manuale completo del dispositivo Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA.

Il manuale per l’uso completo Carrier, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA - che ci dovrebbe aiutare nei primi passi durante l'uso Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA?

Utilizza il modulo sottostante

Se non hai risolto il problema con Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Carrier DOWNFLOW HORIZONTAL 2-SPEED, 2-STAGE 58TMA è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)