Italiano dropdown-ico

Manuale per l’uso Wagner SprayTech 3000, 3500

30 pagine 1.4 mb
Scarica

Vai alla pagina of 30

Summary
  • Wagner SprayTech 3000, 3500 - page 1

    SER VICE/OPERA TION MANU AL Form No. 001-683 FEB2305 Form No. 001-683 FEB2305 ...

  • Wagner SprayTech 3000, 3500 - page 2

    T able of Contents INTRODUCTION Sp ra y & St ri pe S pe ci  ca ti on s 1 Safety W arnings 2 GETTING ST ARTED How to Flush 7 Flushing 8 Setting Up 9 Pressure Relief Procedure 10 Daily Maintenance 10 Starting Up 1 1 Striping Operation 12 Striping T ip Guide 13 REP AIRS/MAINTENANCE INSTRUCTIONS Spray Gun Operation 14 Spray Gun T roubleshooting ...

  • Wagner SprayTech 3000, 3500 - page 3

    Bef ore oper at ing thi s un it, rea d an d fol low all saf ety warn in gs and ins truc tion s rel ated to the usa ge o f thi s eq uipm ent . RE AD, LE ARN , and FOL LOW th e P ress ure Rel ief Proc ed ure on Page 10 a nd und erst and al l w arni ngs on page s 2 thru 6. IMPORT ANT WARNING !! HANDLE THIS UNIT AS Y OU WOULD A L O ADED FIREARM!! High ...

  • Wagner SprayTech 3000, 3500 - page 4

    TIP GUARD AL W A YS have the tip guard in place on the spray gun while spraying. The tip guard alerts you to the injection hazard and helps prevent accidentally placing your ngers or any part of your body close to the spray tip. SPRA Y TIP SAFETY Use extreme caution when cleaning or changing spray tips. If the spray tip clogs while spraying, eng ...

  • Wagner SprayTech 3000, 3500 - page 5

    Saf ety War nings Fluids under high pressure from spray or leaks can penetrate the skin and cause extremely serious injury , including the need for amputation. • NEVER point the spray gun at anyone or any part of the body . • NEVER put hands or ngers over the spray tip. Do not use a rag or any other material over your ngers. Paint will pe ...

  • Wagner SprayTech 3000, 3500 - page 6

    A VOID COMPONENT RUPTURE This sprayer operates at 2500 psi (170 bar). Always be sure that all components and accessories have a maximum working pressure of at least 3000 psi to avoid rupture which can result in serious bodily injury including injection and property damage. • NEVER leave a pressurized sprayer unattended to avoid accidental operati ...

  • Wagner SprayTech 3000, 3500 - page 7

    WHEN ADDING FUEL • T urn engine OFF and let engine cool at least 2 minutes before removing gas cap. • Fill fuel tank outdoors or in well ventilated area. • Do not overll fuel tank. Fill tank to approximately1 inches below top of neck to allow for fuel expansion. • Keep gasoline away from sparks, open ames, pilot lights, heat and ot ...

  • Wagner SprayTech 3000, 3500 - page 8

    WHEN TRANSPORTING EQUIPMENT • T ransport with fuel tank EMPTY or with fuel shut-off valve OFF . WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN T ANK • Store away from furnaces, stoves, water heaters and other appliances that have pilot lights or other ignition source. They can ignite gasoline vapors. Starting engine creates sparking. Sparking ...

  • Wagner SprayTech 3000, 3500 - page 9

    Ho w to F lush FIGURE 1 LOCK TRIGGER TO REMOVE SPRA Y TIP 1. Be sure the gun safety latch is engaged and there is no spray tip in the gun. Refer to Fig. 1. Refer to your separate instruction manual provided with your gun on its safety features and how to engage safety latch. 2. Pour enough clean, compatible solvent (or water when using water-base p ...

  • Wagner SprayTech 3000, 3500 - page 10

    1. New Sprayer Y our Airlessco unit was factory tested in an antifreeze solution which was left in the pump. Before using oil-base paint,  ush with mineral spirits only . Before using water-base paint ush with soapy water , then do a clean water ush. 2. Changing Colors Flush with a compatible solvent such as mineral spirits or water . 3. C ...

  • Wagner SprayTech 3000, 3500 - page 11

    Setting Up to Stripe or Spr ay 1. Connect the hose and gun. a. If the hose is not already installed on the striper , remove the plastic cap plug from the outlet tee at the spray pump, and screw a conductive or grounded 3000 psi airless spray hose onto  uid outlet. b. Connect an airless spray gun to the other end of the hose. c. Do not use steel ...

  • Wagner SprayTech 3000, 3500 - page 12

    Pr essur e R elief Procedur e 1. Keep the displacement pump packing nut/wet cup lubricated with Airlessco TSO (Throat Seal Oil) at all times. The TSO helps protect the rod and the packings. 2. Inspect the packing nut daily . Y our pump has a patented T riple Life Packing System. Packing life will be extended a minimum of three times if the followin ...

  • Wagner SprayTech 3000, 3500 - page 13

    Star ting Up 1. Lear n ho w to oper ate the control valv e. The control valve sets the prime or pressure position as well as the spraying pressure. When the valve is fully counter -clockwise the unit is in the prime position. As the control valve is turned clockwise, the unit’ s output pressure to the gun is gradually increased until the control ...

  • Wagner SprayTech 3000, 3500 - page 14

    Striping Oper a tion 1. Choose handle location The choices are, installing the handle opposite of the single wheel assembly (standard set up) or placing the handle directly over the single wheel assembly . The handle location is really a matter of personal preference, however having the handle away from the single wheel assembly allows for easier l ...

  • Wagner SprayTech 3000, 3500 - page 15

    Striping Tip Guide STRIPING TIP REGULAR P AINTING SPRA Y TIP UNIFORM P A TTERN LIGHT HEA VY Striping Tips should not be used for regular spraying. Striping tips are designed for a single pass application, while spray tips are designed for the 1/3 overlap technique used for spray painting. Spray Tip Replacement: During use high pressure will cause t ...

  • Wagner SprayTech 3000, 3500 - page 16

    Spr ay Gun Oper a tion Reversible Spray T ip T ip Guard T rigger Guard MAJOR COMPONENTS OF SPRA Y GUN & REVERSIBLE REV -TIP ™ SPRA Y GUN Attach spray gun to airless unit and tighten ttings securely . Set the gun safety latch. (Also may be called gun safety lock, or trigger lock) * The gun safety latch should always be set when the gun is n ...

  • Wagner SprayTech 3000, 3500 - page 17

    Spr ay Gun T r oubleshooting DEFECTS CA USE CORRECTION Coarse spray Low pressure Increase the pressure Excessive fogging High pressure Reduce pressure for satisfactory pattern (overspray) Material too thin Use less thinner Pattern too wide Spray angle too lar ge Use smaller spray angle tip Pattern too narrow Spray angle too small Use larger spray a ...

  • Wagner SprayTech 3000, 3500 - page 18

    Field T r oubleshooting PROBLEM CAUSE SOLUTION Unit doesn't prime Airleak due to: • Loose Suction Nut • T ighten Suction Nut • W orn O-Rings • Replace O-Ring (106-01 1) on suction seat, & O-Ring (106- 020) below suction seat • Hole in Suction Hose • Replace Suction Hose (331-290) Stuck or Fouled Balls Service outlet valve sucti ...

  • Wagner SprayTech 3000, 3500 - page 19

    17 Refer to Figure 1 1. Follow the Pressure Relief Procedure on page 10. 2. Flush the material you are spraying out of the machine. 3. Remove the connecting rod shield (331-1 11). 4. Move the piston rod (331-093) to its lowest position by cycling pump slowly . 5. Remove the retaining ring (331-062) from the connecting rod (331-038) and slide the sl ...

  • Wagner SprayTech 3000, 3500 - page 20

    Ser vicing the Piston R od - Outlet V alv e 331-196 331-195 Piston DISASSEMBL Y OF THE OUTLET V AL VE REFER T O FIGURE 3 1. Disconnect the Fluid Pump following instructions on page 17 . 2. Place piston holder (331-195) in a vise. Slide piston into the holder & lock in place with a 3/8” dowel (331-196). 3. Use a 1/4” allen wrench to unscrew ...

  • Wagner SprayTech 3000, 3500 - page 21

    P acking R eplacement Pr ocedur es 19 Fluid Pump Remo val - Refer to Figure 1 1. Follow the Pressure Relief Procedure on page 9. 2. Flush material you are spraying out of the machine. 3. Remove the connecting rod shield (331-1 11). 4. Move the piston rod (331-093) to its lowest position by cycling pump slowly . 5. Remove the retaining ring (331-062 ...

  • Wagner SprayTech 3000, 3500 - page 22

    FIGURE 5 P acking R eplacement Pr ocedur es FIGURE 6 20 3. Push the two bolts (100-318) through the tube spacers (331-074) & screw into the cover assembly (331-234). Using a 1/2” wrench, tighten the two bolts evenly (alternating between them) until you reach 20 ft-lbs. 4. Reassemble lower suction valve assembly by placing the suction seat (33 ...

  • Wagner SprayTech 3000, 3500 - page 23

    I n s p e c t i o n & R e p l a c e m e n t o f C o n t r o l V a l v e , B a l l & S e a t 1. Use a wrench to unscrew the control valve with ring seal. 2. Make sure that the control valve knob turns freely and that its stem is not worn unevenly , mushroomed or otherwise damaged. 3. Remove TC guide, verify that it is unbroken, clean and not ...

  • Wagner SprayTech 3000, 3500 - page 24

    Gear Bo x Assembl y - Par t No. 305-196 22 Part Number Description 100-004 90 Degree Elbow 100-028 Pipe Plug 100-318 HXHD Screw 100-332 Retaining Ring 100-380 Screw 100-381 Screw 100-398 Retaining Ring 1 12-068 Ball Bearing 1 15-019 Hose Connector 1 17-008 Ball Bearing 305-197 Paint Pump Ass’y 305-199 Shaft Pinion 305-287 Machined End Bell 331-03 ...

  • Wagner SprayTech 3000, 3500 - page 25

    Spr ay Gun Assembl y - Par t No. 305-280 Gun Mount Assembl y - Par t No . 305-275 - 23 Part Number Description 100-01 1 Airless 1/4” x 50’ Hose 1 16-103 Cable Retainer Spring 120-1 15 008 Silver Gun w/o T ip 305-275 Gun Mount Ass’y 305-280 Spray Gun Assembly 561-025 Rev-Tip Male Seal 561-026 Rev- T ip Seal 563-317ST Striping T ip 560-517 Pain ...

  • Wagner SprayTech 3000, 3500 - page 26

    Bypass V alv e Assembl y Par t No. 305-264 Part Number Description Qty . 100-040 Hose, Whip 2 1 15-016 Control V alve Seat Ass’y 1 1 15-017 Ball 1 1 15-024 Unloader V alve 1 1 15-028 Stat-O-Seal 1 1 15-031 Guide T .C. 1 188-377 Return Tube 1 305-194 PR Regulator Housing 1 24 ...

  • Wagner SprayTech 3000, 3500 - page 27

    Suction Assembl y P ar t No . 331-290 Part Number Description Qty . 106-020 T eon O-Ring 1 141-015 Hose Clamp (some models only) 1 331-034 Suction Nut 1 331-035 Suction Elbow 1 331-217 Suction Filter 1 25 ...

  • Wagner SprayTech 3000, 3500 - page 28

    F r ame Assembl y Par t No. 305-213 Part Number Description Qty . 100-317 Nut 5/16-18 Centerlock 4 100-320 Wing Screw , 3/8 1 100-370 Screw , Hex Cap 2 1 13-031 Spacer , 5/8 x 1.00 2 1 13-032 Axel, 13” 1 1 19-026 Screw Hex Hd 3 136-131 Chain Sash 1 136-133 Key Ring 1 139-053 Handle, Striper 1 140-029 W asher , Flat, 5/16 8 143-028 W asher , Flat, ...

  • Wagner SprayTech 3000, 3500 - page 29

    REV-GU ARD ™ Part # 560-xxx REV -TIP for Spray Painting 562-xxxST REV -TIP for Striping P O SI -L O C ™ S Y ST E M Snap in centering of tip. No leaks, splashback or mess. S EA L L O CA T I NG HA ND L E T ip handle simplifies installing & aligning the seal. EA SIE ST A SSE MBL Y Fewer parts - Less complicated takes only seconds! I NT ER C HA ...

  • Wagner SprayTech 3000, 3500 - page 30

    XTEND-A-POLE SY STEM Tip Extensions - Complete with Pa tente d SPRA Y CLE AN REV -GU ARD TIP EXTENSIONS, “G” THREAD 032-170 6” Long 032-171 12” Long 032-172 18” Long 032-173 24” Long SWIVEL EXTENSION, “G” THREAD 032-184 36” Long EXTENSIONS (BARE POLES) Add T ip Extension or Swivel Extension to create desired length 032-053 24” L ...

Fabbricante Wagner SprayTech Categoria Paint Sprayer

I documenti che otteniamo dal fabbricante del dispositivoWagner SprayTech 3000, 3500 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Wagner SprayTech
- manuali per l’uso 3000, 3500
- schede prodotto Wagner SprayTech
- opuscoli
- o etichette energetiche Wagner SprayTech 3000, 3500
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Wagner SprayTech 3000, 3500.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Wagner SprayTech 3000, 3500, manuali di manutenzione, brevi manuali o manuali utente Wagner SprayTech 3000, 3500. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Wagner SprayTech 3000, 3500.

Manuali per l’uso simili

Manuale completo del dispositivo Wagner SprayTech 3000, 3500, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Wagner SprayTech 3000, 3500 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Wagner SprayTech 3000, 3500.

Il manuale per l’uso completo Wagner SprayTech, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Wagner SprayTech 3000, 3500 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Wagner SprayTech 3000, 3500, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Wagner SprayTech 3000, 3500 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Wagner SprayTech 3000, 3500 - che ci dovrebbe aiutare nei primi passi durante l'uso Wagner SprayTech 3000, 3500
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Wagner SprayTech 3000, 3500
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Wagner SprayTech 3000, 3500 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Wagner SprayTech 3000, 3500?

Utilizza il modulo sottostante

Se non hai risolto il problema con Wagner SprayTech 3000, 3500 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Wagner SprayTech 3000, 3500 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)