Italiano dropdown-ico

Manuale per l’uso Baldor EXB009A01

30 pagine 0.15 mb
Scarica

Vai alla pagina of 30

Summary
  • Baldor EXB009A01 - page 1

    Resolver to Digital Expansion Board Catalog No. EXB009A01 Installation and Operating Manual 6/98 MN1313 ...

  • Baldor EXB009A01 - page 2

    T able of Contents T able of Contents i Section 1 General Information 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Limited W arranty 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Notice 1-3 . . . . . . . . . . . . . . ...

  • Baldor EXB009A01 - page 3

    ii T able of Contents Section 4 Hardware Setup 4–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connections 4–3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 5 Software Setup 5–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure Control Software 5–1 . . . . . . ...

  • Baldor EXB009A01 - page 4

    Section 1 General Information General Information 1-1 Introduction The Baldor controls represent the latest technology in microprocessor based motor controls. In addition to the user programmable parameters available in every control, many dif ferent expansion boards are available from Baldor to further customize the control to most any application ...

  • Baldor EXB009A01 - page 5

    1-2 General Information Limited Warranty For a period of two (2) years from the date of original purchase, BALDOR will repair or replace without charge controls and accessories which our examination proves to be defective in material or workmanship. This warranty is valid if the unit has not been tampered with by unauthorized persons, misused, abus ...

  • Baldor EXB009A01 - page 6

    General Information 1-3 Safety Notice This equipment contains voltages that may be as great as 1000 volts! Electrical shock can cause serious or fatal injury . Only qualified personnel should attempt the start-up procedure or troubleshoot this equipment. This equipment may be connected to other machines that have rotating parts or parts that are dr ...

  • Baldor EXB009A01 - page 7

    1-4 General Information W ARNING: Be sure the system is properly grounded before applying power . Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury . W ARNING: Do not remove cover for at least five (5) minutes after AC power is disconnected to allow capacit ...

  • Baldor EXB009A01 - page 8

    Section 2 Expansion Board Description Description 2-1 Introduction Resolver to Digital Interface Expansion Board Catalog No. EXB009A01 Group 1 Expansion Board The Resolver to Digital Interface expansion board provides closed loop operation for the Baldor Series 18H, 19H, 20H and 22H controls. The Resolver to Digital Interface can also be used for P ...

  • Baldor EXB009A01 - page 9

    2-2 Description Maximum Motor Speed / Resolver Speed Resolver Speed T ype Maximum Motor Speed (RPM) py p 10 Bits 12 Bits 14 Bits 16 Bits (2 Pole) 1 Speed Resolver 62,400 15,600 3,900 975 (4 Pole) 2 Speed Resolver 31,200 7,800 1,950 487 (6 Pole) 3 Speed Resolver 20,800 5,200 1,300 325 (8 Pole) 4 Speed Resolver 15,600 3,900 975 244 (10 Pole) 5 Speed ...

  • Baldor EXB009A01 - page 10

    Section 3 Installation Installation 3-1 Board Installation This section describes the Expansion Board installation procedure. Caution: Before you proceed, be sure to read and become familiar with the safety precautions at the beginning of this manual. Do not proceed if you are unsure of the safety precautions described. If you have any questions, c ...

  • Baldor EXB009A01 - page 11

    3-2 Installation 1-15HP Size A and B Controls (For all 15H Inverter , 18H V ector , and 23H Servo). Single Expansion Board Installation Procedure: 1. Be sure drive operation is terminated and secured. 2. Remove all power sources from the control. 3. W ait at least 5 minutes for internal capacitors to discharge. 4. Remove the four (4) Phillips head ...

  • Baldor EXB009A01 - page 12

    Installation 3-3 Figure 3-1 Single Expansion Board Installation Remove screw (Labeled MH1 in Main PCB Screen). Install Male/Female Standoff. Install Female/Female Aluminum Standoff. Install Female/Female Nylon Standoff. Main Control Board Expansion Board T erminal tightening torque is 7 lb-in (0.8 Nm) maximum. Figure 3-2 Single Expansion Board Inst ...

  • Baldor EXB009A01 - page 13

    3-4 Installation 1-15HP Size A and B Controls (Continued) Dual Expansion Board Installation Procedure: 1. Be sure drive operation is terminated and secured. 2. Remove all power sources from the control. 3. W ait at least 5 minutes for internal capacitors to discharge. 4. Remove the four (4) Phillips head screws that secure the control cover . 5. Re ...

  • Baldor EXB009A01 - page 14

    Installation 3-5 1-15HP Size A and B Controls Dual Expansion Board Installation (Continued) 13. The mechanical installation of the first expansion board is now complete. Refer to the manual for the Group 2 board and configure any jumpers and switches as desired. Also complete the wiring for this board before you install the cover . 14. When complet ...

  • Baldor EXB009A01 - page 15

    3-6 Installation 15HP Size C and Larger AC Controls (For all 15H Inverter , 21H Line Regen Inverter , 18H V ector , 22H Line Regen V ector and 23H Servo). Single Expansion Board Installation Procedure: 1. Be sure drive operation is terminated and secured. 2. Remove all power sources from the control. 3. W ait at least 5 minutes for internal capacit ...

  • Baldor EXB009A01 - page 16

    Installation 3-7 15HP Size C and Larger AC Controls Single Expansion Board Installation (Continued) Figure 3-4 Single Expansion Board Installation Expansion Board Motor Control Board T erminal tightening torque is 7 lb-in (0.8 Nm) maximum. Figure 3-5 Single Expansion Board Installation #6 Screw Group 1 or 2 Expansion Board Sheet Metal Mounting Plat ...

  • Baldor EXB009A01 - page 17

    3-8 Installation 15HP Size C and Larger AC Controls (Continued) Dual Expansion Board Installation Procedure: 1. Be sure drive operation is terminated and secured. 2. Remove all power sources from the control. 3. W ait at least 5 minutes for internal capacitors to discharge. 4. Remove the four (4) Phillips head screws ( 1 / 4 turn) that secure the c ...

  • Baldor EXB009A01 - page 18

    Installation 3-9 15HP Size C and Larger AC Controls Dual Expansion Board Installation (Continued) 12. When complete, install the control cover using the four (4) Phillips head screws ( 1 / 4 turn). (On floor mounted G size enclosures, close the enclosure door). 13. Restore all power sources to the control. 14. Restore drive operation. Figure 3-6 Du ...

  • Baldor EXB009A01 - page 19

    3-10 Installation SCR DC Controls (For 19H and 20H SCR DC Controls). Single Expansion Board Installation Procedure: 1. Be sure drive operation is terminated and secured. 2. Remove all power sources from the control. 3. W ait at least 5 minutes for internal capacitors to discharge. 4. Slide the expansion board male connector into the female connecto ...

  • Baldor EXB009A01 - page 20

    Installation 3-1 1 SCR DC Controls (Continued) Dual Expansion Board Installation Procedure: 1. Be sure drive operation is terminated and secured. 2. Remove all power sources from the control. 3. W ait at least 5 minutes for internal capacitors to discharge. 4. Slide the Group 1 board male connector into the female connector of the control board. Se ...

  • Baldor EXB009A01 - page 21

    3-12 Installation ...

  • Baldor EXB009A01 - page 22

    Section 4 Hardware Setup Setup 4-1 Important: If the Resolver to Digital expansion board is installed in a V ector control that has a feedback module installed, the feedback module must be removed to prevent interference with the expansion board. Figure 4-1 shows how to identify the feedback module on the DSP Main Control Board. The main control bo ...

  • Baldor EXB009A01 - page 23

    4-2 Setup If your V ector control does not look like the one pictured in Figure 4-1, do not perform the feedback module removal procedure. Instead, continue onto page 4-3. Feedback Module Removal Procedure If your V ector control looks like the one pictured in Figure 4-1, perform the following procedure: The resolver feedback module must be removed ...

  • Baldor EXB009A01 - page 24

    Setup 4-3 Connections W ARNING: High voltage is present on the Resolver to Digital expansion board. Do not touch any circuit board, power device or electrical connection before you first ensure that power has been disconnected and there is no high voltage present from this equipment or other equipment to which it is connected. Electrical shock can ...

  • Baldor EXB009A01 - page 25

    4-4 Setup Figure 4-1 Switch and T erminal Locations 123 4 Side View 5 All switches shown in OFF position. ON OFF DIP Switch 51 52 53 54 55 56 J1 T erminal tightening torque is 7 lb-in (0.8 Nm) maximum. ...

  • Baldor EXB009A01 - page 26

    Setup 4-5 Figure 4-2 Resolver Connections P 51 SINE+ 52 SINE– 53 COS+ 54 COS– 55 REF+ 56 REF– (Common/ Shield) P P P = T wisted Pair R2 R1 S2 S4 S1 S3 T erminal tightening torque is 7 lb-in (0.8 Nm) maximum. T able 4-1 Switch Settings Digital Resolution (Bit ) DIP Switch Number g (Bits) 12345 10 ON ON OFF OFF ON 12 ON OFF OFF OFF ON 14 OFF ON ...

  • Baldor EXB009A01 - page 27

    4-6 Setup ...

  • Baldor EXB009A01 - page 28

    Section 5 Software Setup Software 5-1 Configure Control Software After the Resolver to Digital Interface board has been installed and the DIP switches are correctly set, the control software must be configured. Series 18H and 22H V ector Controls Note: When the Resolver to Digital Interface board is installed, the encoder inputs to the control are ...

  • Baldor EXB009A01 - page 29

    5-2 Software ...

  • Baldor EXB009A01 - page 30

    BALDOR ELECTRIC COMP ANY P .O. Box 2400 Fort Smith, AR 72902–2400 (501) 646–471 1 Fax (501) 648–5792  Baldor Electric Company Printed in USA MN1313 6/98 C&J2500 ...

Fabbricante Baldor Categoria Computer Hardware

I documenti che otteniamo dal fabbricante del dispositivoBaldor EXB009A01 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Baldor
- manuali per l’uso EXB009A01
- schede prodotto Baldor
- opuscoli
- o etichette energetiche Baldor EXB009A01
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Baldor EXB009A01.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Baldor EXB009A01, manuali di manutenzione, brevi manuali o manuali utente Baldor EXB009A01. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Baldor EXB009A01.

Manuali per l’uso simili

Manuale completo del dispositivo Baldor EXB009A01, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Baldor EXB009A01 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Baldor EXB009A01.

Il manuale per l’uso completo Baldor, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Baldor EXB009A01 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Baldor EXB009A01, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Baldor EXB009A01 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Baldor EXB009A01 - che ci dovrebbe aiutare nei primi passi durante l'uso Baldor EXB009A01
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Baldor EXB009A01
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Baldor EXB009A01 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Baldor EXB009A01?

Utilizza il modulo sottostante

Se non hai risolto il problema con Baldor EXB009A01 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Baldor EXB009A01 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)