Italiano dropdown-ico

Manuale per l’uso ATEN CS428

41 pagine 4.6 mb
Scarica

Vai alla pagina of 41

Summary
  • ATEN CS428 - page 1

    4 Console / 8 Port KVM Switch CS428 User Manual www.aten.com cs428_2007-05.book Page i T hursday, May 17, 2007 5:08 PM ...

  • ATEN CS428 - page 2

    CS428 User Manual ii FCC Information This is an FCC Class A product. In a domestic environment this product may cause radio interference in which cas e the user may be required to tak e adequate measures. This equipment has been test ed and found to comply with the limit s for a Class A digital device, pursuant to Part 15 of the FCC Rules. These li ...

  • ATEN CS428 - page 3

    CS428 User Manual iii User Information Online Registration Be sure to register your product at our online support center:  International – http :/ /supp ort.aten.com  North America – http ://www .aten-usa.com/product_registratio n T elephone Suppo rt  International – 886-2-869 2-6959  North America – 1- 8 88-999-A TEN User Notic ...

  • ATEN CS428 - page 4

    CS428 User Manual iv Package Content s The basic CS428 package consists of:  1 CS428 KVM Switch  2 KVM Cable Sets (2L-1701S)  1 Power Adapter  1 Rack Mount Kit  1 User Manual* Check to make sure that all the comp onents are present and that nothing got damaged in shipping . If you encounter a problem, contact your dealer. Read this m ...

  • ATEN CS428 - page 5

    CS428 User Manual v Content s FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • ATEN CS428 - page 6

    CS428 User Manual vi F3 LIST: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 F4 SCAN: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 F5 ADM: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 F6 Set:. . . . ...

  • ATEN CS428 - page 7

    CS428 User Manual vii About this Manual This User Manual is provided to help you get the most from your c/c system. It covers all aspects of installation, configurati on and op erati on. An overview of the information fou nd in th e manual is provided below. Chapter 1, Introduction, introduces you to the CS428 system. It s purpose, features and ben ...

  • ATEN CS428 - page 8

    CS428 User Manual viii Conventions This manual uses the following conven tio ns: Product Information For information abo ut all ATEN produ cts and how they can help you connect without limits, vi si t ATEN on the Web or co ntact an ATEN Authorized Reseller.Vis it ATEN on th e Web for a li st of locations and telephone numbers  International – ...

  • ATEN CS428 - page 9

    1 Chapter 1 Introduction Overview The CS-428 KVM Switch is a control unit that allows fou r independent keyboard, mouse, and moni tor Consoles to access eight computers, either independently or on a multiuser shared ba sis, in a convenient, cost effective manner. A Master View CS-428 unit can c ontrol up to 8 PCs. Sin ce it can be cascaded one leve ...

  • ATEN CS428 - page 10

    CS428 User Manual 2 Features  4 Consoles Control 8 Computers  Up to four users can operate up to 64 computers (via cascading to CS- 138A, CS-9138, CS-12 8A, or CS-124A) at the sam e time  Each console has its own access control  T wo level passw ord security (one Ad min istrator; four User passwords)  Administrator can access an y co ...

  • ATEN CS428 - page 11

    1. Introduction 3 Requirement s Console  A VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on any com puter in the in stallation. If a monitor switches to a computer us ing a resolution that is higher th an the resolution that the monito r can support, serious damage to the mo nitor may result.  A PS/2 ...

  • ATEN CS428 - page 12

    CS428 User Manual 4 Component s Front Panel No. Component Description 1 Port LEDs The Port LEDs provide status information about their corresponding Computer Ports. There is one pair of LEDs for each Port. The one on the left is the On Line LED; the one on the right is the Selected Port LED:  An On Line LED lights ORANGE to indicate that the com ...

  • ATEN CS428 - page 13

    1. Introduction 5 Rear Panel No. Component Desc ription 1 Power Switch A rocker switch to power the system on and off. 2 Console 3 and 4 Connectors Use KVM Cable sets (see Cables , page 3), to connect the components that make up Consoles 3 and 4 to these ports. 3 Power Jack The power adapater cable plugs in here. 4C o n s o l e 2 Microphone and S p ...

  • ATEN CS428 - page 14

    CS428 User Manual 6 This Page Intentionally Left Blank cs428_2007-05.book Page 6 T hur sday, May 17, 2007 5: 08 PM ...

  • ATEN CS428 - page 15

    7 Chapter 2 Hardware Setup S t acking and Mounting The CS428 can be placed on the deskt op or it can be rack mounted, as described in the sections that fo llo w. St acking The unit comes with the stacking brackets already attached. To stack additional units, simply line up the brackets on the top and botto m units, then fit the top unit down onto t ...

  • ATEN CS428 - page 16

    CS428 User Manual 8 2. Use the screws that came with the rack mount kit to screw the mounting brackets into the sides of the unit, as shown in the diagram below: 3. Slide the unit into the rack and secure it to the rack. Single St ation Inst allation The most basic installation is a Single Stage install ation, in which no additional Master Views ar ...

  • ATEN CS428 - page 17

    2. Hardware Setup 9 Note: When you turn the unit On, it undergoes a Power On Self T est. If there is a problem, Port LEDs 1 - 4 flash repeatedly according to a pattern that indicates what the problem is. See see Power On Self Test , page 31 for details. 6. Plug in the power cords and power On all the computers. Note: Y ou must turn on the power to ...

  • ATEN CS428 - page 18

    CS428 User Manual 10 To set up a two stage installation, do the following: 1. Make sure that power to all the devices you will be connecting up, including all preexisting devices on the installation, have been turned off (unplug the power cords of any computers that have the Keyboard Power On function; unplu g the First Stage unit). 2. Use a 2L-160 ...

  • ATEN CS428 - page 19

    11 Chapter 3 Basic Operation Hot Plugging The Master View CS428 support s hot plugging - compo nents can be removed and added back into the installation by unplugging their cables from the KVM ports without the need to shut the unit down. In o rder for hot plugging to work properly, however, these pro cedures must be followed: 1. When hot plugging ...

  • ATEN CS428 - page 20

    CS428 User Manual 12 Port Numbering Each computer on the installation is assigned a unique Port Number (PN). The PN is a one or two segment number that is determined by the Stage Level and KVM port of the KVM switch that the co mputer is connected to. The first segment represents the KVM Po rt number of the First Stage unit (the CS428); the second ...

  • ATEN CS428 - page 21

    13 Chapter 4 OSD Operation OSD Overview On Screen Display (OSD), provides a menu driven interface to handle the computer switching procedur e. All operations start from the OSD Main Menu. To activate the Main Menu, tap either Ctrl key twi ce. Note: 1. The keys must be on the same side (both left, or both right). 2. If using the Ctrl key conflicts w ...

  • ATEN CS428 - page 22

    CS428 User Manual 14 When you invoke the OSD, a screen similar to the one below appears: Note: 1. The diagram depicts the Administra tor's Main Screen. The User Main Screen does not show the F2 and F5 function, since th ey are reserved for the Administrator and can't be accessed by ordinary Users. 2. The OSD always starts in List view , w ...

  • ATEN CS428 - page 23

    4. OSD Operation 15 OSD Navigation  T o dismiss the menu, and d eactivate the OSD, Click the X at the upper right corner of the OSD W indow; or press [Esc] .  T o Logout, click F8 or the Z Z Z symbol at the top of the Main Screen, or press [F8] .  T o move up or down through the list one line at a time, Click the Up and Down T riangle symb ...

  • ATEN CS428 - page 24

    CS428 User Manual 16 OSD Main Menu Headings OSD Functions OSD functions are used to configure an d control the OSD. For example, you can: rapidly switch to any port; scan selected ports only; limit the list you wish to view; designate a port for Quick View scanning; create or edit a port name; or make OSD setting adjustments. To access an OSD funct ...

  • ATEN CS428 - page 25

    4. OSD Operation 17 F2 EDIT : This is an Admi nistrator function. To help remem ber which computer is attached to a particular port, every por t can be given a name. The Edit function allows the Administrator to create, m odify, or delete po rt names. To Edi t a port name: 1. Click the port you want , or use the Navigation Key s to move the highlig ...

  • ATEN CS428 - page 26

    CS428 User Manual 18 F3 LIST : This function lets you broaden or na rro w the scope of which ports the OSD lists. This will be different for each Console, depending on the choices made for that Console. The choi ces and their meanings are given in the table, below: Double Click the choice you want, or move the Hig hlight Bar to it then press [Enter ...

  • ATEN CS428 - page 27

    4. OSD Operation 19 F4 SCAN: Clicking th e F4 field, o r pressing [F 4] initiates Scan Mode , in which the OSD cycles through all th e ports that have been sel ected for scanning with the Scan Mode setting (see SCAN MODE , page 22). When you want to stop at a particular location, press the [Spacebar] to stop scanning.  If the scanning stops on a ...

  • ATEN CS428 - page 28

    CS428 User Manual 20 F5 ADM: F5 allows an Admi nistrator to configur e the OSD operation of the Console. To change a setting Double Click it; or use the Up and Down Arrow Keys to mov e the highlight bar to it then press [Enter] . Note: 1. To avoid Administrator conflict, a pri ority system has been set up in which, by default, Console 1 has priorit ...

  • ATEN CS428 - page 29

    4. OSD Operation 21 Setting Function SET ACCESSIBLE PORTS This function allows Administrators and Users to select which Ports can be accessed from a pa rticular Console. Move the highlight bar to the target computer, then press [Enter] or the [Sp acebar] to toggle access On and Off. If access is On, a plus mark ( + ) appears to indicate so. If acce ...

  • ATEN CS428 - page 30

    CS428 User Manual 22 F6 Set: [F6] allows you to configure the OSD settings for the Console you are working at. To change a setting: 1. Double Click it; or move the highlight bar to it, then press [Enter] 2. Press [Esc] to activate it. After you select an item, a submenu with further choices appears. To make a selection, either Double Click it; or m ...

  • ATEN CS428 - page 31

    4. OSD Operation 23 (Continued from previous page.) Setting Function SCAN DURA TION Determines how long the display dwells on each por t when it cycles through the selected ports in Quick View Scan Mode . Key in a value from 1 - 255 seconds, then press [Enter] . Default is 3 seconds. PRIV A TE MODE The [Enter] key is a toggle that Enables/Disables ...

  • ATEN CS428 - page 32

    CS428 User Manual 24 F7 QV You can broaden or narrow the number of ports that get automati cally scanned by selecting only the ones you want wi th the QV (Quick View Scan) function. [F7] is a toggle that selects or deselects the currently highligh ted port for the Quick View Scan ning function (see F4, above). To select/deselect a port for Quick Vi ...

  • ATEN CS428 - page 33

    25 Appendix Safety Instructions General  Read all of these instructions. Save them for future reference.  Follow all warnings and instructions marked on the dev ice.  Do not place the device on any unstable su rf ace (cart, stand, table, etc.). If the device falls, serious damage wi ll resul t.  Do not use the device near water .  Do ...

  • ATEN CS428 - page 34

    CS428 User Manual 26  T o help protect y our system from sudden, transient increases and decreases in electrical power , use a su rge suppressor , line conditioner , or un-interruptible power supply (U PS).  Position system cables and power cable s carefully; Be sure that nothing rests on any cables.  When connecting or disconnect ing po w ...

  • ATEN CS428 - page 35

    Appendix 27 Rack Mounting  Before working on the rack, ma ke su re that the stabilizer s are secured to the rack, extended to the floor , and that the full w eight of the rack rests on the floor . Install front and side stabilizers on a single rack or front stabilizers for joined multiple ra cks before work ing on the rack.  Always load the r ...

  • ATEN CS428 - page 36

    CS428 User Manual 28 T echnical Support International North America When you contact u s, please have the followin g information ready beforehand:  Product model number, serial number , and date of purchase.  Y our computer configuration, includin g operatin g system, revision level, expansion cards, and software.  Any error messages displ ...

  • ATEN CS428 - page 37

    Appendix 29 Master View - Computer Connection T ables Switches Ty p e Computers 1 CS428 1 - 8 2 CS-128A / CS-138A / CS-9138 8 - 15 3 CS-128A / CS-138A / CS-9138 15 - 22 4 CS-128A / CS-138A / CS-9138 22 - 29 5 CS-128A / CS-138A / CS-9138 29 - 36 6 CS-128A / CS-138A / CS-9138 36 - 43 7 CS-128A / CS-138A / CS-9138 43 - 50 8 CS-128A / CS-138A / CS-9138 ...

  • ATEN CS428 - page 38

    CS428 User Manual 30 Specifications Function Specification Computer Connections Direct 8 Max 64 (via Cascade) Port Selection OSD (On Screen Display Connectors Console 1 & 2 Keyboard 2 x 6-pin Mini DIN Female (Purple) Video 2 x HDB-15 Female Mouse 2 x 6-pin Mini DIN Female (Green) S peaker 2 x Mini S tereo Jack Female (Green) Microphone 2 x Mini ...

  • ATEN CS428 - page 39

    Appendix 31 OSD Factory Default Settings Power On Self T est When you turn the unit On, it undergoes a Power On Self Test. If there is a problem, Port LEDs 1 - 4 flash repeatedly according to a pattern that indicates what the problem is: If any of these problems o ccur, turn the Switch Off, then turn it On again. Setting Function MUL TIUSER MODE En ...

  • ATEN CS428 - page 40

    CS428 User Manual 32 T roubleshooting Symptom Possible Cause Action Keyboard and/or Mouse not responding. The connection f rom the selected port to the targ et comput er has been broken, or the compute r is turned OFF . Check the Online LED for the selected port. If it is not lit: 1. Check to see that the computer is powered On. 2. Check the cables ...

  • ATEN CS428 - page 41

    33 Index C Cables, 3 Components Front Panel, 4 Rear Panel, 5 Connection Tables, 29 F Factory Default Settings, 31 Features, 2 H Hot Plugging, 11 I Installation Cascaded, 9 Single Station, 8 L Limited Warranty, 32 M Mounting, 7 O Online Registration, iii OSD Factory Default Settings, 31 Functions, 16 Main Menu Headings, 16 Navigation, 15 Overview, 1 ...

Fabbricante ATEN Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoATEN CS428 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici ATEN
- manuali per l’uso CS428
- schede prodotto ATEN
- opuscoli
- o etichette energetiche ATEN CS428
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso ATEN CS428.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione ATEN CS428, manuali di manutenzione, brevi manuali o manuali utente ATEN CS428. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto ATEN CS428.

Manuali per l’uso simili

Manuale completo del dispositivo ATEN CS428, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare ATEN CS428 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti ATEN CS428.

Il manuale per l’uso completo ATEN, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale ATEN CS428 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice ATEN CS428, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per ATEN CS428 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo ATEN CS428 - che ci dovrebbe aiutare nei primi passi durante l'uso ATEN CS428
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del ATEN CS428
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio ATEN CS428 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su ATEN CS428?

Utilizza il modulo sottostante

Se non hai risolto il problema con ATEN CS428 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con ATEN CS428 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)