Italiano dropdown-ico

Manuale per l’uso Kenmore 153.331572

40 pagine 2.51 mb
Scarica

Vai alla pagina of 40

Summary
  • Kenmore 153.331572 - page 1

    1 This water heater complies with ANSI Z21.10.1- current edition regarding the accidental or unintended ignition of fl ammable vapors, such as those emitted by gasoline. www .sears.com Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Owner ’ s Manual FOR POT ABLE W A TER HEA TING ONL Y . NOT SUIT ABLE FOR SP ACE HEA TING. NOT FOR USE IN M ...

  • Kenmore 153.331572 - page 2

    2 Fl am m a bl e V apor s FLA MM AB LES FIRE AND EXPLOSION HAZARD Can result in serious injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Storage of or use of gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance can result in ser ...

  • Kenmore 153.331572 - page 3

    3 Fire or Explosion Harzard Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Avoid all ignition sources if you smell Natural or LP gas. Do not expose water heater control to excessive gas pressure. Use only gas shown on rating plate. Maintain required clearances to combustibles. Keep ...

  • Kenmore 153.331572 - page 4

    4 T ABLE OF CONTENTS SAFE INST ALLA TION, USE AND SERVICE ............................................................................................ ..... 2 SAFETY PRECAUTIONS ............................................................................................................ ............... 2-3 PRODUCT W ARRANTY ......................... ...

  • Kenmore 153.331572 - page 5

    5 OPERA TING YOUR W A TER HEA TER ................................................................................................... 22-24 Lighting Instructions ......................................................................................................... ....................................... 22 Checking the Draft .................... ...

  • Kenmore 153.331572 - page 6

    6 12 - YEAR LIMITED W ARRANTY ON W A TER HEA TER For twelve years from the date of purchase, if this water heater is installed and operated in a single-family home in accordanc e with the owner ’s manual instructions and all local applicable plumbing codes, Sears will: 1. Supply free water heater parts for those that are defective in material or ...

  • Kenmore 153.331572 - page 7

    7 CUSTOMER RESPONSIBILITIES Thank Y ou for purchasing a Kenmore water heater . Properly installed and maintained, it should give you years of trouble free service. If you should decide that you want the new water heater professionally installed by Sears call 1-800-4-MY -HOME ® . They will arrange for prompt, quality installation by Sears authorize ...

  • Kenmore 153.331572 - page 8

    8 MA TERIALS AND BASIC TOOLS NEEDED MA TERIALS NEEDED T o simplify the installation Sears has available the installation parts shown below . Y ou may or may not need all of these materials, depending on your type of installation. W A TER HEA TER INST ALLA TION KIT WITH FLEXIBLE CONNECTORS FOR 3/4” (19.05 mm) OR 1/2” (12.7 mm) THREADED OR COPPER ...

  • Kenmore 153.331572 - page 9

    9 TYPICAL INST ALLA TION GET TO KNOW YOUR W A TER HEA TER - GAS MODELS A V ent Pipe B Draft Hood C Anode (Not Shown) D Hot W ater Outlet E Insulation F Gas Supply Piping G Manual Gas Shut-off V alve H Ground Joint Union I Drip Leg (Sediment T rap) * INST ALL IN ACCORDANCE WITH LOCAL CODES. * DRIP LEG AS REQUIRED BY LOCAL CODES. FIGURE 1. J Inner Do ...

  • Kenmore 153.331572 - page 10

    10 Installation Checklist W ater Heater Location W ater heater location is important and can affect system performance. Please check the following: □ Installati on area free of co rrosive elements and flammable materials. □ Cent rally lo c ated wi th th e water pipi ng system (For new installat ions) . Loc ated as c lo se to the g as pipin g an ...

  • Kenmore 153.331572 - page 11

    11 INST ALLA TION INSTRUCTIONS Removing the Old Water Heater FIGURE 2. 1. T urn “OFF” the gas supply to the water heater . If the main gas line shutoff valve serving all gas appliances is used, also shut “OFF” the gas at each appliance. Leave all gas appliances shut “OFF” until the water heater installation is completed. See Figures 2 a ...

  • Kenmore 153.331572 - page 12

    12 Location Requirements Carbon Monoxide Poisoning Hazard W ARNING Do not install in a mobile home. Doing so can result in carbon monoxide poisoning and death. The FVIR System is designed to reduce the risk of flammable vapor-related fires. The patented system protects your family by trapping the burning vapors within the water heater combustion ch ...

  • Kenmore 153.331572 - page 13

    13 IMPORT ANT : The water heater should be located in an area where leakage of the tank or connections will not result in damage to the area adjacent to the water heater or to lower floors of the structure. Due to the normal corrosive action of water , the tank will eventually leak after an extended period of time. Also any external plumbing leak, ...

  • Kenmore 153.331572 - page 14

    14 BACK SIDES TOP VIEW SIDES VENT FRONT 24” MINIMUM FOR SERVICE TOP TO CEILING FIGU R E 10. Filling the W ater Heater Never use this water heater unless it is completely full of water . T o prevent damage to the tank, the tank must be fi lled with water . W ater must fl ow from the hot water faucet before turning “ON” gas to the water heate ...

  • Kenmore 153.331572 - page 15

    15 Gas Pressure W ARNING Explosion Hazard • Gas leaks can not always be detected by smell. • Gas suppliers recommend that you use a gas detector approved by UL or CSA. • For more information, contact your gas supplier . • If a gas leak is detected, follow the “What to do if you smell gas” instructions on the cover of this manual. IMPORT ...

  • Kenmore 153.331572 - page 16

    16 Carbon Monoxide W arning Follow all the local and state codes or , in the absence of local and state codes, the “National Fuel Gas Code”, ANSI Z223.1 (NFP A 54)- current edition to properly install vent system. Failure to do so can result in death, explosion, or carbon monoxide poisoning. W ARNING IMPORT ANT : Air for combustion and ventilat ...

  • Kenmore 153.331572 - page 17

    17 T ABLE 4 Minimum Free Area of Permanent Openings for V entilation and Combustion Air Supply - All Air from Outdoors Only . Based on total BTUH input rating for all utilizing equipment within the con fi ned space. Openin g Sour ce Minimum F ree Area Per O p eni ng (sq . in .) Refer ence Drawing * D i r e c t t o o u t d o o r s 1 sq. in, pe r 40 ...

  • Kenmore 153.331572 - page 18

    18 1 SQ. INCH PER 2000 BTUH CONFINED SPACE 1 SQ. INCH PER 2000 BTUH INLET OUTLET OUTDOOR AIR DUCTS ALL AIR FROM OUTDOORS USING HORIZONTAL DUCTS FIGU R E 16. ALTERNATIVE OPENING LOCATION 1 SQ. INCH PER 3000 BTUH CONFINED SPACE ALL AIR FROM OUTDOORS - USING A SINGLE PERMANENT OPENING FIGU R E 1 7 . V ent Pipe System This water heater uses a non-direc ...

  • Kenmore 153.331572 - page 19

    19 separation, and maintain clearances to combustible materials (Figures 20 and 21). IMPORT ANT : This gas vent must be terminated in a vertical position to facilitate the removal of the burnt gases. An unused chimney flue or masonry enclosure may be used as a passageway for the installation of a gas vent (Figure 21). Common (combined) venting is a ...

  • Kenmore 153.331572 - page 20

    20 Piping Installation Piping, fittings, and valves should be installed according to the installation drawing (Figure 22). If the indoor installation area is subject to freezing temperatures, the water piping must be protected by insulation. The water supply pressure should not exceed 80 psi. If this occurs, a pressure reducing valve with a bypass ...

  • Kenmore 153.331572 - page 21

    21 For protection against excessive pressures and temperatures, a temperature and pressure relief valve must be installed in the opening marked “T & P RELIEF V AL VE.” (See Figure 24). This valve must be design certified by a nationally recognized testing laboratory that maintains periodic inspection of the production of listed equipment or ...

  • Kenmore 153.331572 - page 22

    22 Lighting Instructions Read and understand these directions thoroughly before attempting to light or re-light the pilot. Make sure the view port is not missing or damaged. (See Figure 32.) Make sure the tank is completely filled with water before lighting the pilot. Check the rating plate near the gas control valve/thermostat for the correct gas. ...

  • Kenmore 153.331572 - page 23

    23 Checking the Draft Burn harzard Hot water discharge. Keep clear of relief valve discharge outlet. After successfully lighting the water heater , allow the unit to operate for 15 minutes and check the draft hood relief opening for proper draft (Figure 26). Make sure all other appliances in the area are operating and all doors are closed when perf ...

  • Kenmore 153.331572 - page 24

    24 INDEX BAR TEMPERATURE DIAL 160°F WHITE RODGERS GAS VALVE GAS CONTROL KNOB (OFF-PILOT-ON) 150°F 140°F 130°F 120°F T emperature Time to Produce 2nd & 3rd Settings Degree Burns on Adult Skin VERY HOT= approx. 160°F (71°C) About 1/2 second C = approx. 150°F (66°C) About 1-1/2 seconds B = approx. 140°F (60°C) Less than 5 seconds A = ap ...

  • Kenmore 153.331572 - page 25

    25 SERVICE AND ADJUSTMENT T ank (Sediment) Cleaning Sediment build-up on the tank bottom may create varying amount of noise, and if left in the tank will cause permanent tank failure. In some water areas, you may not be able to drain all sediment deposits by simply draining the tank. In these cases, Mag-Erad (part no. 23600) can be used to help rem ...

  • Kenmore 153.331572 - page 26

    26 Housekeeping V acuum around base of water heater for dust, dirt, and lint on a regular basis. Fire and Explosion Harzard Do not obstruct combustion air openings at the bottom of the water heater . Do not use or store flammable vapor products such as gasoline, solvents or adhesives in the same room or area near water heater or other appliance. At ...

  • Kenmore 153.331572 - page 27

    27 down during freezing temperatures. T o drain the tank, perform the following steps: 1 . T u rn of f the gas to th e water heate r at the ma nual gas shut- of f valve. 2. C los e the c ol d water inlet valve. 3. Ope n a near by hot water fauc et . 4. Co nnec t a hose to t he drain valve and ter minate it to an adequate drain. NOTE: The drain hose ...

  • Kenmore 153.331572 - page 28

    28 MAINTENANCE OF YOUR W A TER HEA TER Replacement Parts IMPORT ANT : The following maintenance procedures are for the FVIR System components and should be performed by a qualified technician. Replacement parts may be ordered from Sears Parts and Service Centers or by calling 1-800-4-MY -HOME (1-800-469-4663). When ordering replacement parts, alway ...

  • Kenmore 153.331572 - page 29

    29 7 . Route the new pi lot tube, th er moc oup le, and ignite r wire throu gh the m anifol d/ bur ner do or ope ning. (Figur e 3 4 ) 8. Re - at tac h the pi lot ass embly to t he pil ot brac ket and secure using the s crew re moved earl ier . 9. Position t he new pi lot tub e thro ugh th e large st op ening of the t wo pi ec e wire c onne cto r . ...

  • Kenmore 153.331572 - page 30

    30 control valve/thermostat. Finally , start the thermocouple nut and turn it all the way in by hand. An additional quarter turn with a 3/8” open-end wrench will then be sufficient to seat the lockwasher . When you are finished, connect the two wire leads that go to the thermal switch. 7 . Rec onne ct th e ignite r wire. 8. T u rn gas sup ply on ...

  • Kenmore 153.331572 - page 31

    31 TEFL O N ® t a p e o r p i p e c o m p o u n d o n l y o n t h e t h r e a d e d sec tio n of the g as c ontr ol valve/ the rm ost at that sc rews into the t ank. 2. Re c onnec t th e gas pi ping to t he gas c ont ro l valve/ ther most at. N OTE: Use an approved T efl on tap e or pipe co mpoun d on the g as pipin g co nnec tio ns. 3. Att ach th ...

  • Kenmore 153.331572 - page 32

    32 TROUBLESHOOTING GUIDE Start Up Conditions Thermal Expansion As water is heated, it expands (thermal expansion). In a closed system, the volume of water will grow . As the volume of water grows, there will be a corresponding increase in water pressure due to thermal expansion. Thermal expansion can cause premature tank failure (leakage). This typ ...

  • Kenmore 153.331572 - page 33

    33 drawn toward the draft hood, shut off water heater and make necessary air supply changes to correct. Condensation Whenever the water heater is filled with cold water , some condensate will form while the burner is on. A water heater may appear to be leaking when in fact the water is condensation. This usually happens when: • A new water heater ...

  • Kenmore 153.331572 - page 34

    34 Read this manual first. Then, before checking the water heater , make sure the gas supply has been turned “OFF”, and never turn the gas “ON” before the tank is completely full of water . Never use this water heater unless it is completely filled with water . T o prevent damage to the tank, the tank must be filled with water . Water must ...

  • Kenmore 153.331572 - page 35

    35 TROUBLESHOOTING CHART PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION BURNER WILL NOT IGNITE 1. Pil ot not lit 2. T her mo stat set to o low 3. No gas 4. Dir t in the gas line s 5. Pi lot line c log ged 6. M ain bur ner line c log ged 7 . Non -func tioning thermo couple 8. Non -f unctioning thermostat 9. Heater inst alle d in a c onf ined ar ea 1 . ...

  • Kenmore 153.331572 - page 36

    36 PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION THERMOST A T F AILS T O SHUT -OFF 1 . The rm ostat n ot funct ionin g prop erly 2. Impr oper c alibrat ion 1 . Replac e ther mo stat 2. Repl ace th er most at COMBUSTION ODORS 1 . Insu f f ic ient s ec onda r y air 2. Water heater f lue or vent system blocked 3. H eater inst alled in a c onf ined area ...

  • Kenmore 153.331572 - page 37

    37 Has the thermal switch tripped? NO Check for insufficient combustion air . Are there openings for make-up air to enter the room? Are the openings of sufficient size? See “Combustion Air Supply and V entilation” section in this manual for requirements. Is there a furnace/air handler in the same room as the water heater? Does the return air du ...

  • Kenmore 153.331572 - page 38

    38 * Not Shown. Model Numbers Key No. Part Description 153.331472 153.331572 1 Anode Rod (Secondary) 9003934 9003934 2 Anode Rod 9003721 9001829 3 Base-Ring Filter 9006616 9006660 4 Burner Head 9006136 9006136 5 Burner Ori fi ce 9006698 9006698 6 Draft Hood 9006647 9006647 7 Drain V alve 9000058 9000058 8 Gas Control V alve F145-1554 F145-1554 9 I ...

  • Kenmore 153.331572 - page 39

    39 NOTES ...

  • Kenmore 153.331572 - page 40

    40 ® Registered Trademark / TM Trademark / SM Service Mark of Sea rs Brands, LLC ® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio d e Sears Brands, LLC MC Marque de commerce / MD Marque dépo sée de Sears Brands, LLC © Sears Brands, LLC Get i t f i xed, at your home or ours! Y our Home For expert troubleshooting and home solutio ...

Fabbricante Kenmore Categoria Water Heater

I documenti che otteniamo dal fabbricante del dispositivoKenmore 153.331572 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Kenmore
- manuali per l’uso 153.331572
- schede prodotto Kenmore
- opuscoli
- o etichette energetiche Kenmore 153.331572
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Kenmore 153.331572.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Kenmore 153.331572, manuali di manutenzione, brevi manuali o manuali utente Kenmore 153.331572. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Kenmore 153.331572.

Manuali per l’uso simili

Manuale completo del dispositivo Kenmore 153.331572, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Kenmore 153.331572 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Kenmore 153.331572.

Il manuale per l’uso completo Kenmore, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Kenmore 153.331572 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Kenmore 153.331572, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Kenmore 153.331572 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Kenmore 153.331572 - che ci dovrebbe aiutare nei primi passi durante l'uso Kenmore 153.331572
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Kenmore 153.331572
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Kenmore 153.331572 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Kenmore 153.331572?

Utilizza il modulo sottostante

Se non hai risolto il problema con Kenmore 153.331572 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Kenmore 153.331572 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)