Italiano dropdown-ico

Manuale per l’uso Quadra-Fire QF130

41 pagine 4.29 mb
Scarica

Vai alla pagina of 41

Summary
  • Quadra-Fire QF130 - page 1

    1 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Models: QFI30 QFI35 • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance. - DO NOT touch any electrical switch. DO NOT use any phone in your building. ...

  • Quadra-Fire QF130 - page 2

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 2 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _____________________ Dealership purchased from: ____________________ ...

  • Quadra-Fire QF130 - page 3

    3 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation which, i ...

  • Quadra-Fire QF130 - page 4

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 4 B. Limited Lifetime W arranty ...

  • Quadra-Fire QF130 - page 5

    5 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 B. Limited Lifetime W arranty (continued) ...

  • Quadra-Fire QF130 - page 6

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 6 C. BTU Specifi cations MODELS: QFI30, QFI35 LABORA TOR Y : Underwriters Laboratories, Inc. (UL) TYPE: V ented Gas Fireplace Heater STANDARD: ANSI Z21.88-2009 CSA 2.33-2009 V ented Gas Fireplace Heaters This product is listed to ANSI standards for “V ented Gas Appliance Heaters” and ...

  • Quadra-Fire QF130 - page 7

    7 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 2 Operating Inst ruc tions Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury . DECORA TIVE D ...

  • Quadra-Fire QF130 - page 8

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 8 C. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figure 2.2 Clear Space ...

  • Quadra-Fire QF130 - page 9

    9 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Figure 2.3 Control Module NG/LP SETTING ST A TUS INDICA TOR LED SELECTOR SWITCH FLAME HI/LO SWITCH I. Before Lighting Fireplace Before operating this fi replace for the fi rst time, have a qualifi ed technician : • V erify all shipping materials have been removed from inside and/or ...

  • Quadra-Fire QF130 - page 10

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 10 J. Lighting Instructions (IPI) The IPI system may be operated with four AA-cell batteries. When using batteries, unplug the transformer . T o prolong bat- tery life, remove them when using the transformer . 1. This appliance is equipped with an ignition device which automatically lights ...

  • Quadra-Fire QF130 - page 11

    11 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Initial Break-in Procedure • The appliance should be run three to four hours continuously on high. • T urn the appliance off and allow it to completely cool. • Remove fi xed glass assembly . See Section 12.H. • Clean fi xed glass assembly . See Section 3. • Replace the fi x ...

  • Quadra-Fire QF130 - page 12

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 12 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid abrasive cleaners ...

  • Quadra-Fire QF130 - page 13

    13 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 V enting Frequency: Seasonally By: Homeowner T ools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow , debris, etc. • V erify termination cap clearance to subsequent construc- tion ( ...

  • Quadra-Fire QF130 - page 14

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 14 Burner Ignition and Operation Frequency: Annually By: Service T echnician T ools needed: Protective gloves, vacuum cleaner , whisk broom, fl ashlight, voltmeter , indexed drill bit set, and a manometer . • V erify burner is properly secured and aligned with pilot or igniter . • Cle ...

  • Quadra-Fire QF130 - page 15

    15 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual VERTICAL TERMINA TION CAP (SECTION 8.F) VENT PIPE (SECTION 8) ...

  • Quadra-Fire QF130 - page 16

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 16 B. Design and Installation Considerations Quadra-Fire gas inserts are designed for installations into solid fuel masonry or factory built fi replaces that have been installed in accordance with the National, Provin- cial, State and local building codes. Fireplaces are to be constructed ...

  • Quadra-Fire QF130 - page 17

    17 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 5 F ireplace Size Requirements Figure 5.1 Fireplace Opening In addition to these dimensions, also reference Clearances and Mantel Projections (Section 5.B). E D C I F B A G H MINIMUM FIREPLACE SIZE Location QFI35 QFI30 Inches Millimeters Inches Millimeters A Rear Width 23-1/2 597 20-1/4 ...

  • Quadra-Fire QF130 - page 18

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 18 B. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, et ...

  • Quadra-Fire QF130 - page 19

    19 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/12 to 8/12 .................................................1.5* O ...

  • Quadra-Fire QF130 - page 20

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 20 7 Installation Preparation Prepare the existing solid fuel masonry or factory built non-combustible fi rebox for installation. A. Inspection and Cleaning Prior to installing the gas insert: • Have the chimney and adjacent structure inspected and cleaned by qualifi ed professionals. ...

  • Quadra-Fire QF130 - page 21

    21 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 B. V enting Components CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. The vertical vent termination system installed on this model includes: • Flexible vent pipe for exhaust air (included wit ...

  • Quadra-Fire QF130 - page 22

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 22 Figure 8.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • T rim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 8.2). • Place 3/8 inch bead of 300º F silicone on fl ue tile top. D. Placing, Securing and Leveling the Appli- ance ...

  • Quadra-Fire QF130 - page 23

    23 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 F . Installing Adaptor and T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 8.4) . T o install adaptor see Figure 8.5. Roof Pitch H (Min.) Ft. Flat to 6/12.................... 1.0* Over 6/12 to 7/12 ........ 1.25* Over 7 ...

  • Quadra-Fire QF130 - page 24

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 24 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a quali fi ed technician (NFI certifi ed or factory-trained) using Hearth & Home T echnologies specifi ed and approved parts. B. Gas Pressure • Optimum applian ...

  • Quadra-Fire QF130 - page 25

    25 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code CSA C22.1. • This appliance comes standard wi ...

  • Quadra-Fire QF130 - page 26

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 26 Figure 10.2 Fan Wiring Diagram BLOWERS BLOWER RECEPT ACLE BLK GRN BLK BLK GRN BLK WHT GRN BLK BLK GRN WHT BLK BLK BLK BLK PLUG INTO 120V EXISTING OUTLET TEMPERA TURE SENSOR SWITCH V ARIABLE SPEED CONTROL DC REGULA TOR RECEPT ACLE JUMPER WIRE PLUG 120V EXISTING OUTLET GRN (2) BLK (2) BLK ...

  • Quadra-Fire QF130 - page 27

    27 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 PLUG 120V EXISTING OUTLET GRN (2) BLK (2) BLK (2) GRN (2) BLK (2) STEPS 3 & 4 WHT (2) BLOWER SPEED CONTROL (RHEOST A T) SENSOR SWITCH STEPS 1 & 2 STEP 5 BLOWERS BLOWER RECEPTICLE BLK GRN BLK BLK GRN BLK WHT GRN BLK BLK GRN WHT BLK BLK PLUG INTO 120V EXISTING OUTLET DC REGULA TOR ...

  • Quadra-Fire QF130 - page 28

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 28 11 F inishing A. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, conc ...

  • Quadra-Fire QF130 - page 29

    29 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 A. Remove Glass Assembly See Section 12.H. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity . D. Accessor ...

  • Quadra-Fire QF130 - page 30

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 30 G. Install the Log Assembly Log Set Assembly: LOGS-QFI30 Models: QFI30 CAUTION: Logs are fragile, handle with care. Install back refractory by placing it against the back of the fi rebox. See Figure 3. The back refractory must be held in the upright position until the side refractory i ...

  • Quadra-Fire QF130 - page 31

    31 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 Log #2 (SRV2227-702) : Rest left end of log on the fl at spot of Log 1. See Figure 6 and Figure 8. The left end of the log should touch the left refractory panel. The right end rests on the burner . Push the right end back, until it touches the edge of the log support. Log #3 (SRV2227- ...

  • Quadra-Fire QF130 - page 32

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 32 Log #4 (SRV2227-705) : Mate the slot on the bottom of the log, shown in Figure 12, with the log pin located on the burner surface. The notch on the right end of the log should mate with the grate bar . See Figure 1 1. Log #5 (SR V2227-706) : Place the left end of the log on the fl at s ...

  • Quadra-Fire QF130 - page 33

    33 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 G. Install the Log Assembly Log Set Assembly: LOGS-QFI35 Models: QFI35 Install back refractory by placing it against the back of the fi rebox. The back refractory must be held in the upright position until the side refractory is installed. Install the left side refractory as shown in F ...

  • Quadra-Fire QF130 - page 34

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 34 Log #2 (SRV2225-703) : Mate the grate tine with the slot on the bottom of Log #2. The back end of the log rests on the log support. The side of the log will contact the left refractory as shown in Figure 7. Figure 7. Place Log #2 Figure 8. Slot on Log #2 Figure 9. Place Log #3 Log #3 (S ...

  • Quadra-Fire QF130 - page 35

    35 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 2225-935B Log #5 (SR V2225-710) : Position Log #5 as shown in Figure 12. Mate the middle and left log pins with the two slots located on the bottom of the log. See Figure 13 for locations of log slots. The smaller end should be pointed toward the right side of the fi rebox. Log #6 (SRV ...

  • Quadra-Fire QF130 - page 36

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 36 I. Air Shutter Setting Air shutter settings should be adjusted by a qualifi ed ser- vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 12.4. NOTICE: If sooting occurs, ...

  • Quadra-Fire QF130 - page 37

    37 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 13 T roubles hoot ing With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualifi ed technician in the diagnosis of a problem and the corrective acti ...

  • Quadra-Fire QF130 - page 38

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 38 Symptom Possible Cause Corrective Action 4. Pilot lights but con- tinues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ame rectifi cation has not occurred.) A. A shorted or loose connection in fl ame sensing rod. ...

  • Quadra-Fire QF130 - page 39

    39 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 14 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. Figure 14.1 Appliance Dimensions A H B C D E I G F N M L K J O R Q P S ELECTRICAL ACCESS GAS LINE ACCESS T MODEL DIMENSIONS Location QFI35 QFI30 Inches Millimeters I ...

  • Quadra-Fire QF130 - page 40

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 40 Figure 14.2 Direct V ent Flex Liner Kits Figure 14.3 Direct V ent Flex Liner Accessory Kits FLASH-DAMP FLEX3-30 LINK-DV -30B (LINK-DV -30) LINK-ZC-ADP DV -46DV A-GK FLEX3-CNCT B. V ent Kits Components Direct V ent Flex Liner Kits (see Figure 14.2) LINK-DV -30B or (LINK-DV -30): Masonry ...

  • Quadra-Fire QF130 - page 41

    Quadra-Fire • QFI30, QFI35 • 2227-900 Rev . H • 1/1 1 46 Quadra-Fire, a brand of Hearth & Home T echnologies Inc. 7571 215 th Street West, Lakeville, MN 55044 www .quadrafi re.com D. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your nearest Quadra-Fire dealer , please visi ...

Fabbricante Quadra-Fire Categoria Indoor Fireplace

I documenti che otteniamo dal fabbricante del dispositivoQuadra-Fire QF130 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Quadra-Fire
- manuali per l’uso QF130
- schede prodotto Quadra-Fire
- opuscoli
- o etichette energetiche Quadra-Fire QF130
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Quadra-Fire QF130.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Quadra-Fire QF130, manuali di manutenzione, brevi manuali o manuali utente Quadra-Fire QF130. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Quadra-Fire QF130.

Manuali per l’uso simili

Manuale completo del dispositivo Quadra-Fire QF130, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Quadra-Fire QF130 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Quadra-Fire QF130.

Il manuale per l’uso completo Quadra-Fire, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Quadra-Fire QF130 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Quadra-Fire QF130, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Quadra-Fire QF130 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Quadra-Fire QF130 - che ci dovrebbe aiutare nei primi passi durante l'uso Quadra-Fire QF130
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Quadra-Fire QF130
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Quadra-Fire QF130 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Quadra-Fire QF130?

Utilizza il modulo sottostante

Se non hai risolto il problema con Quadra-Fire QF130 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Quadra-Fire QF130 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)