-
Kraun KR.XJ - page 1
www .kraun.it Wireless Access Point 54MB Single Port User’s Manual Cod. KR.XJ ...
-
Kraun KR.XJ - page 2
www .kraun.it 2 User’s Manual Contents Package contents 3 1. About this Guide 3 1.1 Purposes 3 1.2 Conventions 3 1.3 Overview of this User Guide 3 2. Introduction 3 2.1 Overview of the AP 3 2.2 Features 3 2.3 Panel Layout 3 2.3.1 The Front Panel 3 2.3.2 The Rear Panel 4 3. Connecting the AP 4 3.1 System Requirements 4 3.2 Installation Environment ...
-
Kraun KR.XJ - page 3
www .kraun.it 3 User’s Manual Package contents The following contents should be found in your box: • One Wireless Access Point 54MB Single Port • One AC power Adapter for Wireless Access Point 54MB Single Port • One Resource CD for Wireless Access Point 54MB Single Port, includ- ing: • This Guide • Other Helpful Information Note: If any ...
-
Kraun KR.XJ - page 4
www .kraun.it 4 User’s Manual 2.3.1 The Rear Panel The rear panel contains the following contents (Viewed from left to right in figure 2-2): • Wireless antenna • Reset button • There are two ways to reset the AP’s factory defaults: 1) Use the Factory Defaults function on System Tools -> Factory De- faults page in the AP’s Web-based U ...
-
Kraun KR.XJ - page 5
www .kraun.it 5 User’s Manual If the result displayed is similar to that shown in figure 4-1, the connec- tion between your PC and the AP has been established. Figure 4-2: Failed result of Ping command If the result displayed is similar to that shown in figure 4-2, it means that your PC has not connected to the AP. Please check it following these ...
-
Kraun KR.XJ - page 6
www .kraun.it 6 User’s Manual • Type - Choose the type for the IP Address: Static IP, Dynamic IP (DHCP). If you choose Static IP, you need to configure the IP Address, Subnet Mask and Gateway. If you choose Dynamic IP (DHCP), you don’t need to configure the other information any more. • IP Address - Enter the IP address of your AP in dotted ...
-
Kraun KR.XJ - page 7
www .kraun.it 7 User’s Manual Figure 5-6b: Wireless Settings for No Region Option • Disable Wireless - The wireless of this AP can be enabled or disabled to allow wireless stations access. If disabled, wireless stations will not be able to access the AP. AP provides five operational modes: Access Point, Client, Repeater, Bridge (point to point) ...
-
Kraun KR.XJ - page 8
www .kraun.it 8 User’s Manual Here is an example of how to configure multi-point bridging. Please fol- low the instructions: Figure 5-10: Point to Multi-point Bridge 1. Configure the Operating Mode of the Access Point Access Points. • Because it is in the central location, set Access Point (AP1) on LAN Segment 1 to Point-to-Multi-Point Bridge m ...
-
Kraun KR.XJ - page 9
www .kraun.it 9 User’s Manual • Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect to the AP without encryption. It is strongly recommended that you choose one of following options to enable security. • WEP - Select 802.11 WEP security. • Type - You can se ...
-
Kraun KR.XJ - page 10
www .kraun.it 10 User’s Manual 2. Enter a simple description of the wireless station in the Description field. For example: Wireless station A. 3. Privilege - Selects the privileges for this entry, one of Allow / Deny / 64-bit / 128-bit / 152-bit. 4. WEP Key - If you select 64-bit, 128-bit or 152-bit in the Privilege field, enter any combination ...
-
Kraun KR.XJ - page 11
www .kraun.it 11 User’s Manual • DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer. • Start IP Address - This field specifies the first of the addresses in the IP address pool. 192.168.1.100 is the default start add ...
-
Kraun KR.XJ - page 12
www .kraun.it 12 User’s Manual There are five submenus under the System Tools menu (shown in figure 5-22): Firmware, Factory Defaults, Reboot, Password, and Log. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 5.7.1 Firmware The page (shown in figure 5 ...
-
Kraun KR.XJ - page 13
www .kraun.it 13 User’s Manual 5.7.5 Log This page (shown in figure 5-27) allows you to query the Logs of the AP. Figure 5-27: System Log The AP can keep logs of all traffic. You can query the logs to find what happened to the AP. Click the Refresh button to refresh the logs. Click the Clear Log button to clear all the logs. Appendix A: FAQ 1. No ...
-
Kraun KR.XJ - page 14
www .kraun.it 14 User’s Manual 3) Click on Properties. The following TCP/IP Properties window will dis- play and the IP Address tab is open on this window by default. 4) Now you have two ways to configure the TCP/IP protocol below: • Assigned by DHCP Sever a. Select Obtain an IP address automatically, as shown in the figure below: Figure B-4: I ...
-
Kraun KR.XJ - page 15
www .kraun.it 15 User’s Manual c. On the DNS Configuration tab, click Enable DNS radio, and type your computer name in to the Host field and a Domain (such as szonline.com) into the Domain field. In the DNS Server Search Or- der field you can type the DNS server IP addresses, which has been provided by your ISP, and click Add button. Shown below: ...
-
Kraun KR.XJ - page 16
www .kraun.it 16 User’s Manual Integrity Protocol (TKIP). TKIP addresses the encryption weaknesses of WEP. Another key component of WPA is built-in authentication that WEP does not offer. With this feature, WPA provides roughly compa- rable security to VPN tunneling with WEP, with the benefit of easier administration and use. This is similar to 8 ...
-
Kraun KR.XJ - page 17
www .kraun.it 17 User’s Manual ...
Hai una domanda su Kraun KR.XJ?
Utilizza il modulo sottostante
Se non hai risolto il problema con Kraun KR.XJ con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Kraun KR.XJ è probabile che voglia condividere il modo di risolverlo.