Italiano dropdown-ico

Manuale per l’uso Makita LS0711Z

32 pagine 0.32 mb
Scarica

Vai alla pagina of 32

Summary
  • Makita LS0711Z - page 1

    INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Slide Compound Sa w Equipped with Electric Blade Brake 190 mm (7-1/2”) MODEL LS0711Z DOUBLE INSULA TION ...

  • Makita LS0711Z - page 2

    2 SPECIFICATIONS Blade diameter : ......................................................................................... 190 mm (7-1/2”) Hole (arbor) diameter : ............................................................................... 15.88 mm (5/8”) Max. Miter angle : ................................................................... ...

  • Makita LS0711Z - page 3

    3 1. KNO W Y OUR PO WER TOOL. Read the owner’ s manual carefully . Learn the tool’ s applications and limitations, as well as the specific potential hazards peculiar to it. 2. KEEP GU ARDS IN PLAC E and in working order . 3. REMO VE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed fr om too ...

  • Makita LS0711Z - page 4

    4 23. POLARIZED PLUGS. T o reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, re verse the plug. If it still does not fit, contact a qualified elec- trician to install the proper outlet. Do ...

  • Makita LS0711Z - page 5

    5 a vise during all operations. Never use your hand to secure the w orkpiece . 5. Never reach ar ound saw blade. 6. T urn off tool and wait for saw blade to stop before mo ving workpiece or chang- ing settings. 7. Unplug tool before c hanging blade or ser- vicing. 8. T o reduce the risk of injur y , return car- riage to the full rear position after ...

  • Makita LS0711Z - page 6

    6 29. NEVER hold workpiece on right side of blade with left hand or vice versa. This is called cross-armed cutting and e xposes user to risk of SERIOUS PERSONAL INJUR Y as shown in the figure. AL W A YS use vise to secure workpiece. 30. Do not abuse cor d. Never yank cor d to disconnect it from the receptac le . Keep cord a way from heat, oil, wate ...

  • Makita LS0711Z - page 7

    7 INST ALLA TION Bench mounting When the tool is shipped, the handle is lock ed in the lowered position by the stopper pin. Release the stopper pin b y lower- ing the handle slightly and pulling the stopper pin. This tool should be bolted with two bolts to a le vel and stab le surf ace using the bolt holes provided in the tool’ s base. This will ...

  • Makita LS0711Z - page 8

    8 If the see-through blade guard becomes dirty , or sawdust adheres to it in such a wa y that the blade is no longer easily visible , unplug the saw and clean the guard carefully with a damp cloth. Do not use solvents or an y petroleum-based cleaners on the plastic guard. If the blade guard is especially dirty and vision through the guard is impair ...

  • Makita LS0711Z - page 9

    9 Maintaining maximum cutting capacity This tool is fa ctor y adjusted to provide the maximum cutting capacity f or a 190 mm (7 - 1/2 ” ) saw blade . When installing a new b lade, alwa ys check the lo wer limit position of the blade and if necessary , adjust it as follo ws: First, unplug the tool. Push the carriage toward the guide f ence fully a ...

  • Makita LS0711Z - page 10

    10 Adjusting the miter angle Loosen the grip by turning counterclockwise. T ur n the turn base while pressing down the loc k lev er . When you hav e mov ed the grip to the position where the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise . CA UTION: • When turning the tur n base, be sure to raise the h ...

  • Makita LS0711Z - page 11

    11 • Do not pull the s witch tr igger hard without pressing in the lock-off b utton. This can cause switch breakage . T o prev ent the switch trigger from being accidentally pulled, a lock-off b utton is provided. T o star t the tool, press in the loc k- off button and pull the s witch trigger . Release the switch trig- ger to stop . W ARNING: ? ...

  • Makita LS0711Z - page 12

    12 Socket wrenc h storage The sock et wrench is stored as shown in the figure. When using the sock et wrench, pull it out of the wrench holder . After using the sock et wrench, retur n it to the wrench holder . Installing or removing sa w blade CA UTION: • Alwa ys be sure that the tool is switched off and unplugged befo re installing or removing ...

  • Makita LS0711Z - page 13

    13 Press the shaft lock to loc k the spindle and use the socket wrench to loosen the he x bolt clockwise. Then remo ve the he x bolt, outer flange and blade. T o install the blade, mount it carefully onto the spindle , mak- ing sure that the direction of the arrow on the surf ace of the blade matches the direction of the arro w on the blade case. I ...

  • Makita LS0711Z - page 14

    14 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy . T o attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remov e the dust bag from the tool and pull the f astener out. Empty the dust bag of its contents, tapping it lightly so as to remo ve par ticles adher- ing to the ...

  • Makita LS0711Z - page 15

    15 V ertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence or the holder assemb ly (optional accessor y). Inser t the vise rod into the hole in the guide f ence or the holder assembly and tighten the screw to secure the vise rod. P osition the vise arm according to the thickness and sha ...

  • Makita LS0711Z - page 16

    16 Holders and holder assembl y (optional accessories) The holders and the holder assembly can be installed on either side as a conv enient means of suppor ting workpieces horizontally . Install them as shown in the figure . Then tighten the screws firmly to secure the holders and the holder assembly . When cutting long workpieces, use the holder-r ...

  • Makita LS0711Z - page 17

    17 1. Press cutting (cutting small workpieces) W or kpieces up to 50 mm (2 ” ) high and 97 mm (3-13/16 ” ) wide can be cut in the f ollowing wa y . Push the carriage toward the guide f ence fully and tighten the clamp screw on the turn base clockwise to secure the carriage. Secure the workpiece with the vise. Switch on the tool without the blad ...

  • Makita LS0711Z - page 18

    18 • Ne ver perf or m the slide cut with the handle lock ed in the lowered position b y pressing the stopper pin. • Ne ver loosen the clamp screw which secures the carriage while the blade is rotating. This ma y cause serious injur y . 3. Miter cutting Ref er to the previously cov ered “ Adjusting the miter angle ” . 4. Bevel cut Loosen the ...

  • Makita LS0711Z - page 19

    19 When perfo r ming compound cutting, refer to “ Press cut- ting ” , “ Slide cutting ” , “ Miter cutting ” and “ Be vel cut ” e xplanations. 6. Cutting cro wn and cove moldings Crown and co ve moldings can be cut on a compound miter saw with the moldings laid flat on the turn base. There are two common types of crown moldings and o ...

  • Makita LS0711Z - page 20

    20 Example: In the case of cutting 52/38 ° type crown molding f or position (1) in Fig. A: • Tilt and secure be vel angle setting to 33.9 ° LEFT . • Adjust and secure miter angle setting to 31.6 ° RIGHT . • La y crown molding with its broad back (hidden) surf ace down on the tur n base with its CEILING CONT ACT EDGE against the guide f enc ...

  • Makita LS0711Z - page 21

    21 EN0002-1 Compound Miter Saw Miter and Bevel Angle Settings 000031 52 ˚ 38 ˚ Ceiling W all W all to Crown Molding Angle: 52/38 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) 60 43.0 46.8 101 30.1 26.9 141 15.3 12. ...

  • Makita LS0711Z - page 22

    22 EN0003-1 Compound Miter Saw Miter and Bevel Angle Settings 000032 45 ˚ 45 ˚ Ceiling W all W all to Crown Molding Angle: 45 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) 60 37.8 50.8 101 26.7 30.2 141 13.7 14.1 6 ...

  • Makita LS0711Z - page 23

    23 7. Cutting aluminum ex trusion When securing aluminum e xtr usions, use spacer b locks or pieces of scrap as shown in the figure to pre v ent def or mation of the aluminum. Use a cutting lubricant when cutting the aluminum e xtrusion to prev ent build-up of the aluminum material on the blade. CA UTION: • Ne ver attempt to cut thick or round al ...

  • Makita LS0711Z - page 24

    24 9. Cutting repetitive lengths When cutting se veral pieces of stoc k to the same length, ranging from 220 mm (8 - 5/8 ” ) to 385 mm (15 - 1/8 ” ), use of the set plate (optional accessor y) will f acilitate more efficient operation. Install the set plate on the holder (optional accessor y) as shown in the figure. Align the cutting line on yo ...

  • Makita LS0711Z - page 25

    25 Carr y the tool by carrying grip as shown in the figure. If y ou remov e the holders, dust bag, etc., you can carry the tool more easily . CA UTION: • Alwa ys secure all moving por tions before carrying the tool. • Stopper pin is f or carr ying and storage pur poses only and not f or any cutting operations. MAINTENANCE CA UTION: • Alwa ys ...

  • Makita LS0711Z - page 26

    26 Make sure that the pointer points to 0 ° on the miter scale. If the pointer does not point to 0 ° , loosen the screw which secures the pointer and adjust the pointer so that it will point to 0 ° . 2. Bevel angle (1) 0 ° be vel angle Push the carriage toward the guide f ence and tighten the clamp screw on the turn base to secure the carriage. ...

  • Makita LS0711Z - page 27

    27 Make sure that the pointer on the arm point to 0 ° on the be vel scale on the arm holder . If it does not point to 0 ° , loosen the screw which secures the pointer and adjust the pointer so that it will point to 0 ° . (2) 45 ° be vel angle Adjust the 45 ° be vel angle only after perf or ming 0 ° be vel angle adjustment. T o adjust left 45 ...

  • Makita LS0711Z - page 28

    28 After use • After use, wipe off chips and dust adhering to the tool with a cloth or the like . Keep the b lade guard clean according to the directions in the pre viously covered section titled “ Blade guard ” . Lubricate the sliding por tions with machine oil to prev ent rust. • When storing the tool, pull the carr iage toward y ou fully ...

  • Makita LS0711Z - page 29

    29 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut ...

  • Makita LS0711Z - page 30

    30 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade ...

  • Makita LS0711Z - page 31

    31 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair ...

  • Makita LS0711Z - page 32

    W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th defects or other reproductiv e har m. Some examples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o ...

Fabbricante Makita Categoria Chainsaw

I documenti che otteniamo dal fabbricante del dispositivoMakita LS0711Z possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Makita
- manuali per l’uso LS0711Z
- schede prodotto Makita
- opuscoli
- o etichette energetiche Makita LS0711Z
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Makita LS0711Z.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Makita LS0711Z, manuali di manutenzione, brevi manuali o manuali utente Makita LS0711Z. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Makita LS0711Z.

Manuali per l’uso simili

Manuale completo del dispositivo Makita LS0711Z, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Makita LS0711Z dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Makita LS0711Z.

Il manuale per l’uso completo Makita, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Makita LS0711Z - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Makita LS0711Z, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Makita LS0711Z che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Makita LS0711Z - che ci dovrebbe aiutare nei primi passi durante l'uso Makita LS0711Z
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Makita LS0711Z
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Makita LS0711Z in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Makita LS0711Z?

Utilizza il modulo sottostante

Se non hai risolto il problema con Makita LS0711Z con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Makita LS0711Z è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)