Italiano dropdown-ico

Manuale per l’uso Cub Cadet LT1042

40 pagine 4.62 mb
Scarica

Vai alla pagina of 40

Summary
  • Cub Cadet LT1042 - page 1

    FORM NO . 769-01514F.f m IMPOR T ANT : READ SAFETY R ULE S AND INSTR UCTIONS CAREFULL Y PRINTED IN U .S.A. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-co vered land unless the engine’s exhaust system is equipped with a spark arrest er mee ...

  • Cub Cadet LT1042 - page 2

    2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Ma nual is an important part of your new lawn tractor. It will help you assemble, pr epare and maintain the unit fo r best performance. Plea se read and understand wh at it says. Before you start as sembling your new equipment , plea se locate the model plate on th e equipment and copy the ...

  • Cub Cadet LT1042 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out import ant safety instructions wh ich, if not followed, could endan ger the personal safe ty and/or propert y of yourself and o thers. Read and follo w all instructions in this manua l before attemptin g to operate this machine . Failure to comply with these instruction ...

  • Cub Cadet LT1042 - page 4

    4 23. Muf fler and engine become hot and can cause a burn. Do not touch. 24. Check overhead cle arances carefully before driving under low hang ing tree branches, wire s, door openings etc ., where the oper ator may be struck or pulled from the unit, which could re sult in serious injury. 25. Disenga ge all attachment clutches, depress t he brake p ...

  • Cub Cadet LT1042 - page 5

    5 e. Use extreme car e when approaching blind corners, doorways, sh rubs, trees or other objects that may block your vision of a child who may run into th e machine. f. To avoid back-over ac cidents, always disengage the cutting blad e(s) before shifting i nto reverse. The “Reverse Caution Mode” should not be used when children or others are ar ...

  • Cub Cadet LT1042 - page 6

    6 8. Never tamper with the safety interlock syst em or other safety devices. Check the ir proper operation regu larly. 9. After striking a foreign ob ject, stop the engine, disconnect the spark plug wire(s) and ground against the engine. Thoroug hly inspect the machine for any damage. Repair the damage bef ore starting and operating. 10. Never atte ...

  • Cub Cadet LT1042 - page 7

    7 SECTION 2: SLOPE GAUGE 3IGHTANDHOLDTHISLEVELWITHAVERTICALTREE ORACORNEROFABUILDING ORAFENCEPOST &OLDALONGDOTTEDLINEREPRESENTSASLOPE  ...

  • Cub Cadet LT1042 - page 8

    8 SECTION 3: TRACTOR SET-UP Gas and Oil Fill-up The gasoline tank is located un der the fender and has a capacity of t hree and-a-h alf gallons. Un thread th e fuel cap by turn ing it count erclockwise. Use only c lean, fresh (under 30 days old), unleaded gasoline. Fill tank to no more than four inches below the top of the filler neck to allow spac ...

  • Cub Cadet LT1042 - page 9

    9 SECTION 4: KNOW YOUR LAWN TRACTOR Figure 1 NOTE: Any reference in this manual to t he RIGHT or LEFT si de of the tra ctor is observed from operat or’s position. A Systems Indicator M onitor/Hour Meter H PTO (Blade Enga ge) Knob B Throttle Control Lever I Brake Pedal C Choke Contro l J Drive Pedal D Parking Brake Le ver K Cruise Control Lever E ...

  • Cub Cadet LT1042 - page 10

    10 Thro tt l e C on t rol Le ver The throttle co ntrol lever is located on the left side of the tractor’s dash panel. This lever controls the spee d of the engine. When set in a given positio n, the throttle will maintain a uniform engine speed. IMPORT ANT: When operating th e tractor with the cu tting deck engaged, be certain that the throttle l ...

  • Cub Cadet LT1042 - page 11

    11 Systems Indicator Monitor / Hour Meter LCD Located in the center of the tra ctor’s cons ole, the systems indicator monitor reco rds, and displays on its LCD, hours of trac tor operati on whenever the ign ition key is rotated out of the STOP po sition. The Indicator Monitor will also remind the operator of maintenance intervals fo r changing th ...

  • Cub Cadet LT1042 - page 12

    12 SECTION 5: OPERATING YOUR LAWN TRACTOR Safety Interlock Switches This tractor is equipped with a safet y interlock system for the pr otection of the ope rator. If the interlock system should ever malfunction, do not operate the tractor . Contact you r Cub Cadet dealer. • The safety interlock syste m prevents the engine from cranking or starti ...

  • Cub Cadet LT1042 - page 13

    13 Setting the Gauge Wheels Select the height posit ion of the cutting deck by placing the deck lift lever in any of the six d ifferent cutting height notches on the ri ght fender. Adjust the deck wheels so th at they are between ¼-inch and ½-inch above the gr ound as follows. WARNING: Keep hands and feet away from the dischar ge opening of the c ...

  • Cub Cadet LT1042 - page 14

    14 Engaging the Pa rking Brake To engage the parking brake: • Fully depress the bra ke pedal and hold it while gently pushing the parking brake le ver downward. • Hold the parking brake lever down while removing your foot from the brake pedal. • Once engaged, t he parking brake lever and the brake pedal will lock in the “down” position. T ...

  • Cub Cadet LT1042 - page 15

    15 • Depress the br ake pedal to disengage the cruise control and stop the tractor. • Lightly depress th e drive pedal. To change the directi on of travel to reverse when operating with cruise control, depress the brake pedal to disengag e the cruise control an d bring the tractor to a complete stop. Then slo wly depress the rear portion of the ...

  • Cub Cadet LT1042 - page 16

    16 • For best result s it is recommended that the first two laps be cut with the discharge thrown towar ds the center. A fter the firs t two laps, reverse the directio n to throw th e discharge to the ou tside for the balance of cuttin g. This will give a bett er appearance to the lawn. • Do not cut the grass t oo short. Short grass invites wee ...

  • Cub Cadet LT1042 - page 17

    17 SECTION 6: MAKING ADJUSTMENTS WARNING: Ne v er attempt to make an y adjustments while the engine is running, e xcept where specified in th e operator’ s manual . Leveling the Deck NOTE: Check the tractor’ s tire pressure before performing any de ck leveling adjustments. Refer to Tires on page 25 for informati on regarding tire pressure. Fron ...

  • Cub Cadet LT1042 - page 18

    18 P arking Brake Adjustment WARNING: Never attempt to a djust the brakes while the engin e is running. Always disengage PTO, stop eng ine and remove ke y to prevent uninten ded starting. If the tractor does not co me to a complete stop when the brake peda l is completely depres sed, or if the tractor’s rear wheels can roll with the pa rking brak ...

  • Cub Cadet LT1042 - page 19

    19 SECTION 7: MAINTAINING YOUR LAWN TRACTOR NOTE: Re fer to Maintenance Chart on page 30 for a reference of recommend ed maintenance intervals. WARNING: Before performing any maintenance or rep airs, disengage PTO, set parking brake, st op engine and remove key to prevent unint ended starti ng. Engine Maintenance, repa ir, or replacement of the emi ...

  • Cub Cadet LT1042 - page 20

    20 IMPORT ANT: The engine may overheat and/or damage may result if the oil level is below the ADD or over the FULL on the dipstick. • Reinstall the oil fill cap/dips tick securely onto the oil fill tube. IMPORT ANT: The oil fill cap/dip sti ck must be installed securely onto the tube at all ti mes when the engine is operating . Severe engine dama ...

  • Cub Cadet LT1042 - page 21

    21 • Slowly pour oil into the fill tube. Fill th e crankcase until the oil level reaches the full ( F ) ma rk on the dipstick (Refer to Figure 14 on Page 19). • Reinstall the oil fill cap/dips tick securely into the oil fill tube. IMPORT ANT: The oil fill cap/dipstick must b e installed securely onto the tube at all ti mes when the engine is op ...

  • Cub Cadet LT1042 - page 22

    22 • Check the gap using a fee ler gauge and adjust, if necessary, by carefully bending th e ground electrode. See Figu re 15. Set the spark plug gap to .76 mm (0.030 in.). Figure 15 • Reinstall the spark plug into the cylin der head. Torque the spark plug to 38.0 /43.4 N·m (28/32 ft. lb. ). • Place the spark plug wire boot over the spark pl ...

  • Cub Cadet LT1042 - page 23

    23 Lubrication WARNING: Before lubricatin g, repa iring, or inspecti ng, always disengage PTO , set parking brake, st op engine and remove key to prevent unint ended starti ng. Engine Refer to Engine on pag e 19 for in struction rega rding all engine-related lub rication. Front Wheels Each of the front wheel axles and rims is equipped with a grease ...

  • Cub Cadet LT1042 - page 24

    24 • Make sure fuel is reachin g the carburetor. Check the fuel lines and fuel pu mp for restrictio ns or faulty components, repla ce as necessary. • Make sure t he air cleaner eleme nt is clean and all air cleaner elem ent component s are secure. If, after checking the ite ms listed above, the engine is hard to start, runs roughly, or stalls a ...

  • Cub Cadet LT1042 - page 25

    25 SECTION 8: SERVICE Tire s WARNING: Never exceed the maxim um inflation pressure sh own on the sidewall of the tire. The recommende d operating tire pressur e is approximately 1 0 psi for the rear tires a nd 14 psi for the front tires. Refer to th e tire sidewa ll for exact t ire manufa cturer’s recommended or maximum psi. Do no t overinflate. ...

  • Cub Cadet LT1042 - page 26

    26 Battery The battery is sealed and is maintenance-free. Acid levels cannot be checked and f luid can not be added. • Always keep the battery ca bles and terminals clean and free o f corrosive build-up. • After cleaning the bat tery and terminals, apply a light coat of petroleum jelly or grease to both terminals • Always keep the rubber boot ...

  • Cub Cadet LT1042 - page 27

    27 Hydrostatic T ransmission Keep the area around the transmission cooling fan free of grass and debris at all ti mes. The hydrostatic transmission is sealed at the factory and is maintenance fr ee. The fluid lev el cannot be checked and on most models , cannot be changed. IMPORT ANT: Several tracto r components and pa rts (pedals, seat, fe nder, f ...

  • Cub Cadet LT1042 - page 28

    28 46-inch Decks • Carefully grasp the idle r pulley and pivot it toward the tractor’s left side to relieve t ension on the belt. See Figure 24. Figure 2 4 • With belt tension relieved, car efully remove the belt from a round the left-hand spindle pulley . 50-inch Decks • To ease in removing the belt in later steps, loosen, but do not remov ...

  • Cub Cadet LT1042 - page 29

    29 L T1042 L T1050 L T1045 & L T1046 ...

  • Cub Cadet LT1042 - page 30

    30 SECTION 9: OFF-SEASON STORAGE Clean and lubricate the tr actor as instructed in Section 7: MAINTAINING YOUR LAWN TRACTOR on page 19 of this manual before sto ring for an extended period . Engine If the engine will be out of service for tw o months or more, use the followin g storage procedure: • Clean the exterior surfac es of the engine. • ...

  • Cub Cadet LT1042 - page 31

    31 SECTION 11: MAINTENANCE LOG Please keep a record of the maintenance performed on your tractor. Date Hour Meter Maintenance P erfo rmed by ...

  • Cub Cadet LT1042 - page 32

    32 SECTION 12: TROUBLESHOOTING T r ouble P ossibl e Cause(s) Corrective Actio n Engine fails to start PT O/Blade Engage knob engaged . P arking brake not engaged. Spark pl ug wire(s) disconnected. Throttle control le v er not in correct star ting positio n. Chok e not activ ated Fuel tank empty , or stale fuel. Bloc ked fuel line. F aulty spark pl ...

  • Cub Cadet LT1042 - page 33

    33 SECTION 13: ATTACHMENTS & ACCESSORIES The following attach ments and accessories are compa tible for Series 1000 Lawn Tra ctors . See your Cub Cadet dealer or the retailer from which yo u purchased your trac tor for informat ion regarding price and availability. NOTE: Cub Cadet Series 1000 lawn tractors are NOT d esigned for use with any typ ...

  • Cub Cadet LT1042 - page 34

    34 SECTION 14: REPLACEMENT PARTS NOTE: Download a complete Cub Cadet Series 1000 Parts Manua l free of charge at www.cubcad et.com or phone (800) 80 0-7310 to purchase a Parts Manual ( Form No. 769-10578F). L T1042 L T1045 L T1046 L T1050 Champion Spar k Plug(s) RC12YC RC12YC RC12YC RC12YC Ko h l er Air Filter (P ape r Element) 20-083-0 2-S 20-083- ...

  • Cub Cadet LT1042 - page 35

    35 SECTION 15: SPECIFICATIONS* * Cub Cadet reserves the right to change product spec ifications, design, and standard equipment wi thout notice and without incurring oblig ation ** Kohler’s horsepower ratings exceed Society of Automo tive Engineers Small Engine Test Code J1940. Actual engine horsepower is lower an d a ffected by, but not limited ...

  • Cub Cadet LT1042 - page 36

    36 CALIFORNIA EMISSION CONTROL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The California Air Resources Board and Cub Cadet LLC are pleased to ex plain the evaporative emission co ntrol system warrant y on your 2006 lawn mower . In California, new lawn mower must be designed, built and equip ped to meet the Stat e’ s stringent a ...

  • Cub Cadet LT1042 - page 37

    K OHLER CO . FEDERAL AND CALI FORNIA EMISSION CONTROL SYSTEMS LIMITED W ARRANTY UTILITY AND LA WN AND GARDEN ENGINES The U.S. Environmental Protection Agency (EP A) , the California Air Resources Board (CARB), and K ohler Co. are pleased to explain the Federal and California Emission Control Systems Warr anty on your small off-road equipment engine ...

  • Cub Cadet LT1042 - page 38

    IMPORT ANT: T o o btai n warra nt y coverag e owner mu st pre sent an or ig inal proof of p urch ase an d app lic abl e mainte nanc e rec ord s to the s er vi cing d ealer. Please s ee the o perator ’s manual for info rmat ion on re quired m ainten ance a nd s erv ic e in te rv al s . The limited w arranty set forth below is giv en by Cub Ca det ...

  • Cub Cadet LT1042 - page 39

    39 ...

  • Cub Cadet LT1042 - page 40

    CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 ...

Fabbricante Cub Cadet Categoria Lawn Mower

I documenti che otteniamo dal fabbricante del dispositivoCub Cadet LT1042 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cub Cadet
- manuali per l’uso LT1042
- schede prodotto Cub Cadet
- opuscoli
- o etichette energetiche Cub Cadet LT1042
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cub Cadet LT1042.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cub Cadet LT1042, manuali di manutenzione, brevi manuali o manuali utente Cub Cadet LT1042. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cub Cadet LT1042.

Manuali per l’uso simili

Manuale completo del dispositivo Cub Cadet LT1042, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cub Cadet LT1042 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cub Cadet LT1042.

Il manuale per l’uso completo Cub Cadet, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cub Cadet LT1042 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cub Cadet LT1042, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cub Cadet LT1042 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cub Cadet LT1042 - che ci dovrebbe aiutare nei primi passi durante l'uso Cub Cadet LT1042
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cub Cadet LT1042
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cub Cadet LT1042 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cub Cadet LT1042?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cub Cadet LT1042 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cub Cadet LT1042 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)