Italiano dropdown-ico

Manuale per l’uso Franklin 5870206300

28 pagine 2.11 mb
Scarica

Vai alla pagina of 28

Summary
  • Franklin 5870206300 - page 1

    Constant Pr essur e W ater System S ub D rive 300 Installation Manual ...

  • Franklin 5870206300 - page 2

    2 Contents Description and Features ................................................................................ 4 Included Items .................................................................................................. 5 How It W orks ..................................................................................................... ...

  • Franklin 5870206300 - page 3

    3 T able 1: SubDrive Models Model Name Part Number Use with Motor Series SubDrive300 5870206300 (NEMA 4) 234 317 xxxx (5.0 Hp) ...

  • Franklin 5870206300 - page 4

    4 Description and Featur es The Franklin Electric SubDrive300 is a dependable residential and light commercial water system contr oller that uses advanced electronics to enhance the performance of standard submersible pumps. When used with the speci fi ed Franklin Electric motor (see T able 1), the SubDrive eliminates pressur e cycling associated ...

  • Franklin 5870206300 - page 5

    5 Included Items A. Controller Unit B. Strain Relief Fittings C. Pressur e Shut-off Sensor and Boot D. Pr essure Sensor and Boot Franklin Ele ctri c is n ow o f fer ing an int rod uct ory warran ty exte nsion on S ubDriv e 75, Sub Driv e 150 and M onoDr ive. The ex ten ded war ran ty i s f ree, bu t the Su bDriv e/M ono - Driv e must be registered ...

  • Franklin 5870206300 - page 6

    6 How It W orks The Franklin Electric SubDrive300 is designed to be part of a system that consists of only four components: A. Standard Pump and Franklin Electric Motor . B. SubDrive Controller . C. Small Pressur e T ank (for tank size, see T able 3). D. Franklin Electric Pressure Sensor (pr ovided). E. Franklin Electric Pressur e Shut-Off Sensor ( ...

  • Franklin 5870206300 - page 7

    7 Motor Soft Start Normally , when there is a demand for water , the SubDrive300 will be operating to accurately maintain system pressur e. Whenever the SubDrive300 detects that water is being used, the controller always “ramps up” the motor speed while gradually increasing voltage, r esulting in a cooler motor and lower start-up current compar ...

  • Franklin 5870206300 - page 8

    8 Pump Sizing The SubDrive300 is con fi gur ed at the factory for use with 3 Hp pumps that are mounted to 5 Hp Franklin Electric thr ee-phase motors. In general, the SubDrive300 will enhance the performance of a 3 Hp pump to a similar or better performance than a conventional 5 Hp pump of the same fl owrating (pump series). T o select the proper ...

  • Franklin 5870206300 - page 9

    9 Underload Sensitivity for Shallow W ells The SubDrive300 controller is con fi gured at the factory to ensur e detection of Underload faults in a wide variety of pumping applications. In rare cases (as with certain pumps in shallow wells) this trip level may result in nuisance faults. If the pump is installed in a shallow well, activate the contr ...

  • Franklin 5870206300 - page 10

    10 ▲ WARNING ! Serious or fatal electrical shock may result fr om failure to connect the ground terminal to the motor , SubDrive controller , metal plumbing, or other metal near the motor or cable, using wire no smaller than motor cable wir es. T o minimize risk of electrical shock, disconnect power before working on or around the SubDrive300 sys ...

  • Franklin 5870206300 - page 11

    11 Contr oller Location Selection The SubDrive controller is intended for operation in ambient temperatur es up to 125°F (51°C) at 230 V AC input. The following r ecommendations will help in selection of the proper location of the SubDrive unit: 1. A tank tee is recommended for mounting the tank, pr essure sensor , pressur e gauge, and pressur e ...

  • Franklin 5870206300 - page 12

    12 4. For indoor or outdoor installations. 5. The SubDrive300 should only be mounted with the wiring end oriented downward. The contr oller should not be placed in direct sunlight or other locations subject to direct rain or snow . 6. The mounting location should have access to 230 V AC electrical supply and to the submersible motor wiring. T o avo ...

  • Franklin 5870206300 - page 13

    13 Cir cuit Breaker and Wir e Sizing The minimum circuit br eaker size and maximum allowable wire lengths for connection of motor to the SubDrive300 are given in the following table: A 10-foot section of cable is provided with the SubDrive300 to connect the pressur e sensors. NOTE: • Maximum allowable wire lengths ar e measured between the contro ...

  • Franklin 5870206300 - page 14

    14 Pow er Supply Fr om Circuit Breaker* Quick Refer ence Guid e P/N 587 020 6300 P u Fr a El e M o PRESSURE SENSOR SHUT-OFF INT FAN INV FAN PFC FAN NO NO COM RELAY SW2 SW1 O N Congur a 1 OFF ON Outp u From P ower Sourc e L1 L2 (Input) * Note : T o avoid possible interference with other appliances, please refer to the enclosed installation guide ...

  • Franklin 5870206300 - page 15

    15 e SubDrive300 (not to scale) T ank Precharge Ination Valve Pressur e Gauge Pressur e Sensor T o Residence Pressure S witch Set Point (PSI) 25 30 35 40 45 55 60 65 70 75 80 Pressure T ank Pre-Charge (PSI) 18 21 25 28 32 35 39 42 46 49 53 56 Pressur e Setting Guide 50 (F actory set) Pressur e Relief V alve Discharge into drain rated for max pum ...

  • Franklin 5870206300 - page 16

    16 Pr essure T ank The SubDrive needs only a small pressur e tank to maintain constant pressur e (see table below for recommended tank size). For pumps rated 12 gpm or more, a slightly lar ger tank is r ecommended for optimum pressur e regulation. The SubDrive can also use an existing tank with a much lar ger capacity . T able 3: Minimum Pressur e ...

  • Franklin 5870206300 - page 17

    17 Installation Pr ocedure 1. Disconnect electrical power at the main breaker . 2. Drain the system (if applicable). 3. Install the pressur e sensor and pressur e shut-off sensor at the pressur e tank tee downstream of the pr essure tank (the pr essure tank should be between the pressur e sensor and the pump). The sensors have a ¼-18 National Pipe ...

  • Franklin 5870206300 - page 18

    18 Wiring Connections 1. V erify that the power has been shut off at the main breaker . 2. V erify that the dedicated branch circuit for the SubDrive300 is equipped with a properly-sized cir cuit breaker . Refer to T able 2 (Page 13) for minimum breaker size. 3. Use the appropriate strain r elief or conduit connectors. T ype B liquid tight fi ttin ...

  • Franklin 5870206300 - page 19

    19 6. Feed the 230 V AC power leads thr ough the bottom left side of the SubDrive300 controller and connect them to the terminals marked L1, L2, and GND (Figure 3). A 10-foot section of pr essure sensor cable is pr ovided with the controller , but it is possible to use similar 22 AWG wire for distances up to 100 feet from the pr essure sensor . A 1 ...

  • Franklin 5870206300 - page 20

    20 10A. Connect the other end of the pressure sensor cable with the two spade terminals to the pressur e sensor . The connections are interchangeable (Figur e 4A). 10B. Connect the other end of the pr essure sensor cable with the two ¼" quick connect terminals to the pressur e shut-off sensor . The connections are inter changeable (Figure 4B) ...

  • Franklin 5870206300 - page 21

    21 Start-Up and Operation Apply power to the controller . A steady green light indicates that the SubDrive300 has power but the pump is not running. The green light will fl ash continuously when the pump is running. Leaky Systems Leaky water systems might keep the controller running due to the accurate pressur e sensing capability of the pressur e ...

  • Franklin 5870206300 - page 22

    22 NOTES: (A) Operating temperature is speci fi ed at full output power when installed as described in Controller Location Selection on Page 11. (B) Refer to Page 23 for detailed mounting dimensions. (C) If a pump other than the default rating is used, refer to Page 8 for drive con fi guration. Input from Power Source (single-phase) V oltage 190- ...

  • Franklin 5870206300 - page 23

    23 Mounting Dimensions 14.75” 12.00” 15.34” 8.75” 4.75” ...

  • Franklin 5870206300 - page 24

    24 Diagnostic Fault Codes Should an application or system problem occur , built-in diagnostics will protect the system. The r ed “F AUL T” light on the front of the SubDrive300 controller will fl ash a given number of times to indicate the nature of the fault. In some cases, the system will shut itself off until corr ective action has been tak ...

  • Franklin 5870206300 - page 25

    25 System T roubleshooting Guide Symptom Possible Cause Corrective Action W ater fl ow rate is not as high as expected. Motor is running backwards. V erify motor connections. See Figure 2 in the “Wiring Connections” section. T emperature in the controller is too high. If the controller’ s heat exchanger becomes too hot, the controller will r ...

  • Franklin 5870206300 - page 26

    26 Underload Smart Reset If a motor Underload fault condition occurs, the most likely cause is an overpumped or dry well. T o allow the well to recover , the SubDrive300 controller will wait 30 seconds to 5 minutes, determined by duration of the previous run time, befor e restarting the motor . For example, the fi rst time the fault occurs, the co ...

  • Franklin 5870206300 - page 27

    TOLL-FREE HELP FROM A FRIEND Franklin Electric Submersible Service Hotline 800-348-2420 ...

  • Franklin 5870206300 - page 28

    400 E. Spring Street Bluffton, IN 46714 Tel: 260-824-2900 Fax: 260-824-2909 www.franklin-electric.com M1491 11.05 225286101 Rev. 1 ...

Fabbricante Franklin Categoria Water Pump

I documenti che otteniamo dal fabbricante del dispositivoFranklin 5870206300 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Franklin
- manuali per l’uso 5870206300
- schede prodotto Franklin
- opuscoli
- o etichette energetiche Franklin 5870206300
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Franklin 5870206300.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Franklin 5870206300, manuali di manutenzione, brevi manuali o manuali utente Franklin 5870206300. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Franklin 5870206300.

Manuali per l’uso simili

Manuale completo del dispositivo Franklin 5870206300, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Franklin 5870206300 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Franklin 5870206300.

Il manuale per l’uso completo Franklin, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Franklin 5870206300 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Franklin 5870206300, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Franklin 5870206300 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Franklin 5870206300 - che ci dovrebbe aiutare nei primi passi durante l'uso Franklin 5870206300
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Franklin 5870206300
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Franklin 5870206300 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Franklin 5870206300?

Utilizza il modulo sottostante

Se non hai risolto il problema con Franklin 5870206300 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Franklin 5870206300 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)