Italiano dropdown-ico

Manuale per l’uso Aarrow Fires Becton Bunny

32 pagine 0.56 mb
Scarica

Vai alla pagina of 32

Summary
  • Aarrow Fires Becton Bunny - page 1

    Aarrow Fires Ltd The Fireworks Bridport Dorset, DT6 3BE Great Britain T el. (44) 01308 427234 Fax. (44) 01308 427441 www .aarrowfires.com The Becton MK 3 Range of Gas S toves Operating & Installation Manual PLEASE RET AIN THESE INSTRUCTIONS FOR FUTURE REFERENCE FOR USE IN COUNTRIES GB & IE Rev 1 1 Part No. AFS1 125 (Becton 7 MK 3 Gas S tove ...

  • Aarrow Fires Becton Bunny - page 2

    Congratulations on your choice of an Aarrow Stove. More than 20 years experience has been put into the development of our Becton Family to ensure ultimate performance and years of trouble free enjoyment. Every detail on the fire has been carefully engineered and designed which is why we are so confident in the reliability of our product that we off ...

  • Aarrow Fires Becton Bunny - page 3

    Page INTRODUCTION Safety Notices 4 General Information 4 Statutory Requirements 5 OPERA TING INSTRUCTIONS T echnical Data 6 Fire Dimensions 6 Fitting the Lining Panels 7 Arranging the Coals 8 Lighting & Controlling The Fire 9-10 INST ALLA TION Installing The Fire 1 1 Fitting The Feet 1 1 Flue System 1 1-13 Fire Location 13 Combustible Shelf Cle ...

  • Aarrow Fires Becton Bunny - page 4

    References in this manual to British Standards and Statutory Regulations and Requirements apply only to the United Kingdom. For Ireland the rules in force must be used. Before installation, check that the local distribution conditions, nature of the gas, pressure and the adjustment of the appliance are compatible. The manual is an important part of ...

  • Aarrow Fires Becton Bunny - page 5

    IMPOR T ANT NOTICES A qualified gas engineer must carry out the installation and servicing of this appliance in accordance with these instructions and in compliance with current Building Regulations. Such person must be a registered CORGI engineer . This appliance is designed to run on natural gas only . W arning - Only use the appliance with the s ...

  • Aarrow Fires Becton Bunny - page 6

    6 Becton Bunny & Becton 7 mk3 Gas stoves OPERA TING INSTRUCTIONS FIRE DIMENSIONS Category I 2H For use in GB and IE at a supply pressure of 20mbar TECHNICAL DA T A Becton Bunny Natural Gas Becton 7 Natural Gas Main Burner Injector Max. Heat Setting Heat Input (net) 3.7 kW 5.0 kW Gas Rate 0.391m 3 /hour 0.529m 3 /hour Cold Setting Pressure 1.5mb ...

  • Aarrow Fires Becton Bunny - page 7

    FITTING THE LINING P ANELS Becton 7 only . The lining panels supplied are to be installed into the fire before the coal matrix is fitted. Note: The lining panels are reversible (brick or plain pattern) Ensure the appliance is cold. W ith the fire door open, the glass retaining frame and the coal set removed, proceed as follows: Do not force the lin ...

  • Aarrow Fires Becton Bunny - page 8

    ARRANGING THE COALS Safety Notice - Please see SAFETY NOTICES ref. Coal set page 4. W arning: The coals and the coal matrices ar e fragile ensure they ar e handled carefully . Ensure location is corr ect. Do not force the matrix into position. If the coals and/or the coal matrices are damaged they must be r eplaced with genuine Aarrow r eplacement ...

  • Aarrow Fires Becton Bunny - page 9

    LIGHTING & CONTROLLING THE FIRE Under no circumstance must the fire be operated if the glass is cracked or broken. Open the gas control access door situated at the bottom of the appliance. Always use the control door HANDLE. S tep 1a. T o ignite the pilot push the control knob in, turn anti-clockwise towards the spark position and hold in for 1 ...

  • Aarrow Fires Becton Bunny - page 10

    Fig 5d Fig 5e S tep 3. T o turn the main burner off while keeping the pilot alight, rotate the operating knob back to the PILOT position. (Fig 5e) Fig 5f S tep 4 . T o extinguish the pilot, turn the control knob to the OFF position. (Fig 5f) Incorporated into the pilot assembly is a flame failure device designed to shut off the gas supply in the ev ...

  • Aarrow Fires Becton Bunny - page 11

    INST ALLING THE FIRE Y our CORGI qualified gas engineer should install the fir e in accor dance with the following r egulations and standar ds:- The Gas Safety (Installation and Use) Regulations 1998 (as amended). The Building Regulations for England and W ales 2000 r ef; Appr oved Document J 2002 edition (issued by the DTLR). The Building S tandar ...

  • Aarrow Fires Becton Bunny - page 12

    The Becton gas stove is designed so that the flue can be fitted to either the top or the rear of the appliance. Fit the flue spigot and blanking plate for either top or rear flue outlet in accordance with figure 6a or 6b (below). Lock the blanking plate in place by rotating anti- clockwise and tighten by tapping gently with a block of wood and mall ...

  • Aarrow Fires Becton Bunny - page 13

    Fig. 7b. Fig. 7c FIRE LOCA TION The appliance must not be installed in a room or space, which contains a bath or shower . This fire is designed for use with either top or rear flue outlets and must be mounted on a hearth with a minimum of 12mm non-combustible material thickness. There must be a minimum of 200mm clearance from the sides of the fire ...

  • Aarrow Fires Becton Bunny - page 14

    The minimum height from the extreme top surface of the fire to the underside of a shelf or other projection made of wood or any other combustible material is shown on graph 1. Graph 1.Combustible Shelf Clearances The recommended minimum height from the extreme top surface of the fire to the underside of a non combustible shelf is 100mm. 14 Becton B ...

  • Aarrow Fires Becton Bunny - page 15

    HEAR TH REQUIREMENTS T o comply with current Building Regulations the fire must stand on a fireproof hearth, which has an upper fireproof layer of 12mm non-combustible material. If the rear of the fire is to be pushed up against a surface it must be of a non-combustible material. The hearth must protrude at least 25mm in front of the glass window a ...

  • Aarrow Fires Becton Bunny - page 16

    FIRE TESTING Flame failur e device testing S tep 1 Ignite the appliance in accordance with page 9 and run for 60 seconds. S tep 2 T urn the appliance off to extinguish the pilot, listen for a snap at the control valve. This should occur within 60 seconds of the pilot flame being extinguished. The snap sound will be the magnet disengaging, and thus ...

  • Aarrow Fires Becton Bunny - page 17

    Becton Bunny & Becton 7 mk3 Gas stoves 17 INST ALLA TION CHECK LIST CHECKLIST Hearths, Fir eplaces, Flues and chimneys This checklist is to ensure hearths, fireplaces, flues and chimneys are satisfactory , and to show what you have done to comply with the requirements of The Building Regulations 2000 Approved Document J 2002. 1. Building addres ...

  • Aarrow Fires Becton Bunny - page 18

    DET AIL OF PILOT ASSEMBL Y It is strongly recommended to leave the pilot on permanently . This will keep the fire and its components, including the ceramic coal set in a warmer state and assist ignition to the burner . This in turn will reduce condensation in the chimney and any associated flue problems. The pilot can be viewed through the L/H & ...

  • Aarrow Fires Becton Bunny - page 19

    Becton Bunny & Becton 7 mk3 Gas stoves 19 SER VICING DOOR TRIM Becton Fire doors are fitted with a brushed steel finish trim as standard. The trim is secured using 3 off tabs and located in the slot section of the trim and secured with 3 off nuts. (See Fig. 1 1a below .) Fig. 1 1a Location of the 3 off tabs Note! T o fit a tracery the trim must ...

  • Aarrow Fires Becton Bunny - page 20

    BURNER ASSEMBL Y T o remove the burner assembly proceed as follows; Ensure the appliance is cold. S tep 1 T urn off the gas supply at the gas service cock. S tep 2 Disconnect the supply inlet pipe at the rear of the fire. S tep 3 Open door and remove the glass frame and glass gasket assembly . S tep 4 Remove the coal set and fire box linings. S tep ...

  • Aarrow Fires Becton Bunny - page 21

    ANNUAL SER VICE THIS GAS APPLIANCE MUST BE SERVICED EVERY TWEL VE MONTHS BY A QUALIFIED GAS ENGINEER. See "SAFETY NOTICES" ref coal set page 4. Ensure the appliance is cold. S tep 1 Isolate the gas supply to the fire using the gas cock supplied at installation. S tep 2 Open the fire door , (Held closed using a magnet). S tep 3 Remove the ...

  • Aarrow Fires Becton Bunny - page 22

    22 Becton Bunny & Becton 7 mk3 Gas stoves SER VICING Is the gas supply turned on? Does the pilot ignite? Ye s Does the pilot stay alight? Ye s Does the main burner light? Ye s Fire satisfactory No Is their air in the system? Ye s Is the main injector blocked? Ye s Clean and replace as necessary Is the supply pressure correct? No Is the thermoco ...

  • Aarrow Fires Becton Bunny - page 23

    GENERAL COMPONENTS Spare parts can be obtained by contacting the original supplier of the fir e or Aarr ow Fires. Fire Body Ancillary Components. Only use genuine Aarrow parts. ACCESSORIES AND OPTIONS Paint- Matching aerosol paint to tone in any connecting flues, pipes or surrounding metalwork T racery or T rim - Note: When fitted one replaces the ...

  • Aarrow Fires Becton Bunny - page 24

    24 Becton Bunny & Becton 7 mk3 Gas stoves NOTES ...

  • Aarrow Fires Becton Bunny - page 25

    Becton Bunny & Becton 7 mk3 Gas stoves 25 NOTES ...

  • Aarrow Fires Becton Bunny - page 26

    26 Becton Bunny & Becton 7 mk3 Gas stoves SP ARE P AR TS 1. Becton 7 mk3 Coal Set - AFGS1075 AFGS1074 - AFGS089 AFGS089 AFGS090 AFGS090 AFGS091A AFGS091 AFGS1073 AFGS1073 AFS047 AFS047 1a. Becton Bunny mk3 Coal Set 2. Co-pilot assembly 3. Elbow Injector 4. Gas Control V alve 5. Magnetic Catch for mk3 Gas Fires. 6. Hinge Kit T o Fit Either Door ...

  • Aarrow Fires Becton Bunny - page 27

    Becton Bunny & Becton 7 mk3 Gas stoves 27 SP ARE P AR TS AFGS1085 AFGS1085 AFGS1076 AFGS1077 AFGS080 AFGS080 AFS094A AFS095 AFGS1078 AFGS1079 AFGS1080 AFGS1081 7. Control Door Handle Assembly 8. Burner & Fixing 9. Pipe Set Complete W ith Connectors 10. Decorative Door Surround (T rim) 1 1. Fire Door Assembly complete with Magnet Lock and T ...

  • Aarrow Fires Becton Bunny - page 28

    28 Becton Bunny & Becton 7 MK3 Gas stoves SP ARE P AR TS - AFGS1072 AFGS093 AFGS093 15. Becton 7 mk3 Lining Kit 16. Large Ceramic Panel Part Description V isual Aid (not to scale) Bunny mk3 Part No. Becton 7 mk3 Part No. AFGS094 AFGS094 17. Medium Ceramic Panel 18. Small Ceramic Panel AFGS1084 AFGS1084 AFGS025 AFGS025 AFS1 125 AFS1 125 19. Gas ...

  • Aarrow Fires Becton Bunny - page 29

    GUARANTEE Once again we would like to thank you for buying a Becton fire. When you buy an Aarrow Fir e, you are not only buying a first class appliance - you are buying a commitment from us to look after you and your appliance. The Becton Gas Stoves come with a Lifetime Guarantee against splitting or cracking of the main body . The main body being ...

  • Aarrow Fires Becton Bunny - page 30

    Should you have any questions about your Becton Gas Stove that is not covered in this manual please con- tact your Aarrow retailer . Please keep all repair receipts safely . Please ensure you have this manual available when an engineer visits as they will complete the service record chart. 30 Becton Bunny & Becton 7 mk3 Gas stoves SER VICE RECO ...

  • Aarrow Fires Becton Bunny - page 31

    Lifetime Guarantee For your peace of mind Aarrow Fires gives a Lifetime Guarantee against manufacturing defects of the main body* of its Becton range of fires. Additionally , all other parts are covered by a one year no quibble replacement guarantee. This guarantee covers replacement of the item only and does not extend to any other costs, includin ...

  • Aarrow Fires Becton Bunny - page 32

    FINAL F ACT OR Y CHECK LIST BK027 Model.................................. Serial No............................. I’ve checked it and it’ s O.K. Assembled by ............................. Checked by ................................ Date of Purchase.................................... Name and address of supplier ................................. ...

Fabbricante Aarrow Fires Categoria Indoor Fireplace

I documenti che otteniamo dal fabbricante del dispositivoAarrow Fires Becton Bunny possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Aarrow Fires
- manuali per l’uso Becton Bunny
- schede prodotto Aarrow Fires
- opuscoli
- o etichette energetiche Aarrow Fires Becton Bunny
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Aarrow Fires Becton Bunny.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Aarrow Fires Becton Bunny, manuali di manutenzione, brevi manuali o manuali utente Aarrow Fires Becton Bunny. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Aarrow Fires Becton Bunny.

Manuali per l’uso simili

Manuale completo del dispositivo Aarrow Fires Becton Bunny, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Aarrow Fires Becton Bunny dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Aarrow Fires Becton Bunny.

Il manuale per l’uso completo Aarrow Fires, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Aarrow Fires Becton Bunny - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Aarrow Fires Becton Bunny, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Aarrow Fires Becton Bunny che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Aarrow Fires Becton Bunny - che ci dovrebbe aiutare nei primi passi durante l'uso Aarrow Fires Becton Bunny
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Aarrow Fires Becton Bunny
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Aarrow Fires Becton Bunny in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Aarrow Fires Becton Bunny?

Utilizza il modulo sottostante

Se non hai risolto il problema con Aarrow Fires Becton Bunny con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Aarrow Fires Becton Bunny è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)