-
Patton electronic 2172A - page 1
USER MANUAL MODEL 2172A CopperLINK™ High Speed Ethernet Extender SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2172A-UM Rev . A Revised 4/8/10 An ISO-9001Cer tified Company This is a Class A device and is intended for use in a light industrial (commercial) environment only . It is not intended nor approved for use in a ...
-
Patton electronic 2172A - page 2
2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Regulatory Information ................................................................. 4 EMC Directive:.............................................................................. 4 Low-Voltage Direcive (Safety): ......................... ...
-
Patton electronic 2172A - page 3
3 D Distance Chart, Based on 24 AWG (0.5 MM) .......................... 19 ...
-
Patton electronic 2172A - page 4
4 1.0 WARRANTY INFORMATION P atton Electronics warrants all Model 2172A components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment. This warranty is limited to def ects in w orkmanship or materials, and does not cov er customer damage, ab use or ...
-
Patton electronic 2172A - page 5
5 of P ar t 15 of FCC rules, which are designed to provide reasonab le pro- tection from such interf erence in a commercial installation. Howe ver , there is no guarantee that interf erence will not occur in a par ticular instal- lation. If the de vice does cause interf erence to radio or tele vision recep- tion, which can be determined by disconne ...
-
Patton electronic 2172A - page 6
6 1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualified service person- nel. • Do not open the device when the power cord is con- nected. For systems without a power switch and without an external power adapter , line voltages are present within the device when ...
-
Patton electronic 2172A - page 7
7 In accordance with the requirements of council direc- tive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you sepa- rate this product from other waste and scrap and deliver to the WEEE collection system in your country for recy- cling. This device is NOT intended nor approved for connec- tion to the ...
-
Patton electronic 2172A - page 8
8 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor . If any questions or prob lems ar ise during installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007 ...
-
Patton electronic 2172A - page 9
9 Figure 1. T ypical application The pair of 2172A models work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application. 3.0 INSTALLATION T o install the 2172A Ethernet Extender , do the follo wing: 1. Connect the line interf ace between the units (ref er to section 3.1, “C ...
-
Patton electronic 2172A - page 10
10 Figure 2. Model 2172A standalone rear panel 3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 2172A suppor ts communication between two peer Ethernet LAN sites ov er a distance of up to 4,250 ft (1.3 km) over 24 A WG (0.5 mm) twisted-pair wire. Note Actual distance and link performance ma y vary depending on the environment and type/gauge ...
-
Patton electronic 2172A - page 11
11 1. T o function properly , the two Model 2172As m ust be connected together using twisted-pair , unconditioned, dr y , metal wire, between 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable . 2. The Model 2172A is equipped with an RJ-45 interf ace jack that can be used on the CopperL ...
-
Patton electronic 2172A - page 12
12 Figure 4. Model 2172A 10/100Base-T RJ-45 Connector Pinout. 3.3 CONNECTING POWER The Model 2172A does not hav e a power s witch, so it powers up as soon as it is plugged in. An e xternal AC or DC pow er supply is av ailable separately . This connec- tion is made via the barrel jack on the rear panel of the Model 2172A. No configuration is necess ...
-
Patton electronic 2172A - page 13
13 Figure 5. Removing protectiv e cov er Figure 6 on page 13 shows the orientation of the DIP switches in the On and Off positions. Figure 6. DIP switch orientation Power Link Ethernet C o p p e r L IN K ™ H i g h S p e e d E t h e r n e t E x t e n d e r 1234 ON Push toggle up for ON position Switch toggle Push toggle down for OFF position 1234 ...
-
Patton electronic 2172A - page 14
14 4.2 CONFIGURING DIP SWITCH S1 DIP s witch S1 is where you configure the CopperLINK line . The f ollowing tables describe the configuration f or the 2172A. 5.0 OPERATION Once the Model 2172As are properly installed, they should operate transparently . No user settings required. This section describes reading the LED status monitors. 5.1 POWER U ...
-
Patton electronic 2172A - page 15
15 5.2 FRONT PANEL LED STATUS MONITORS The Model 2172A f eatures six front panel LEDs that monitor power , the Ethernet signals, the CopperLINK connection, and the remote/local set- ting. Figure 7 shows the front panel location of each LED . T ab le 2 on page 15 describes the LED functions. Figure 7. Model 2172A front panel T able 2: F ront panel L ...
-
Patton electronic 2172A - page 16
16 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • T w o shielded RJ-45, 10/100Base-T , IEEE 802.3 Ethernet • CopperLINK Connection: Shielded RJ-45 A.2 TRANSMISSION LINE T w o-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE • Line Rate: 50/50 Mbps, upstream/downstream. Additional five line rates are a vailab ...
-
Patton electronic 2172A - page 17
17 APPENDIX B MODEL 2172A SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2172A/E CopperLINK Multi Rate 100 Mbps Ethernet Extender ; No power supply 2172A/E-2PK CopperLINK Multi Rate 100 Mbps Ethernet Extender Kit (2 units preset to local and remo ...
-
Patton electronic 2172A - page 18
18 APPENDIX C MODEL 2172A SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection ...
-
Patton electronic 2172A - page 19
19 APPENDIX D DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note The actual distance and link performance ma y vary depending on the environment and type/gauge of wire used. Note DS = downstream, US = upstream Line Rate Distance in feet (km) Throughput at Max Distance (bits per second) 4/1 4250 ft (1.3 km) 4,629,408 (DS) 1,175,328 (US) 15/2 3500 ft (1 ...
-
Patton electronic 2172A - page 20
20 Cop yright © 2010. P atton Electronics Company All Rights Reser ved. ...
Hai una domanda su Patton electronic 2172A?
Utilizza il modulo sottostante
Se non hai risolto il problema con Patton electronic 2172A con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Patton electronic 2172A è probabile che voglia condividere il modo di risolverlo.