-
JVC RX-7040B - page 1
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. LVT1170-001B [J] RX-7040B/RX-7042S A UDIO/VIDEO CONTR OL RECEIVER INSTR UCTIONS Cover_2_7040[J] 04.1.21, 15:54 1 ...
-
JVC RX-7040B - page 2
G-1 CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. ATTENTION Afin d’éviter tout risque d’électrocution, d’incendie, etc.: 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil. 2. Ne pas exposer l’ ...
-
JVC RX-7040B - page 3
1 T able of Contents Basic Settings ........................................... 21 Quick Speaker Setup ................................................................ 21 Basic Setting Items ................................................................... 22 Basic Procedure ........................................................................ ...
-
JVC RX-7040B - page 4
2 Intr oduction W e would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference. Featur es CC (Compensative Compression) conver ter CC Con verter eliminates jitter and ripples, ...
-
JVC RX-7040B - page 5
3 Par ts Identification See pages in parentheses for details. 1 DIMMER button (18, 40) 2 Standby/On buttons (13, 40 – 43) A UDIO, DVD , CA TV/DBS , VCR , TV 3 Source selection b uttons (13 – 15, 19, 20, 36, 40 – 43) D VD MUL TI, D VD, CD*, T APE/CDR*, TV/DBS, VCR, FM/AM* * When you press one of these source selection buttons on the remote con ...
-
JVC RX-7040B - page 6
4 Front Panel Press down on PUSH-OPEN. How to open the front door See pages in parentheses for details. 1 ST ANDBY/ON button and ST ANDBY lamp (13) 2 SPEAKERS ON/OFF 1/2 buttons (15) 3 SURR OUND button (32, 33, 40) 4 Remote sensor 5 Display window (F or details, see “Display window” on the next page.) 6 Source selection b uttons (13 – 15, 17, ...
-
JVC RX-7040B - page 7
5 See pages in parentheses for details. 1 DU AL indicator (31) 2 AN ALOG indicator (16) 3 DIGIT AL A UTO indicator (16) 4 96/24 indicator (31) 5 MUL TI indicator (36) 6 NEO:6 indicator (31) 7 TUNED indicator (19) 8 PR O LOGIC indicator (30) PR O LOGIC II indicator (31) 9 STEREO indicator (19, 20) 0 A UTO MUTING indicator (20) - VIR TU AL SB (Surrou ...
-
JVC RX-7040B - page 8
6 Getting Star ted This section explains how to connect audio/video components and speakers to the receiver , and how to connect the power supply . Checking the Supplied Accessories Check to be sure you hav e all of the following items, which are supplied with the receiv er . The number in the parentheses indicates quantity of the pieces supplied. ...
-
JVC RX-7040B - page 9
7 Connecting the Speakers and Subwoofer Y ou can connect the following speakers: • T wo pairs of front speak ers. • One pair of surround speak ers. • One surround back speaker or one pair of sur round back speakers. • One center speak er. • One po wered subwoofer . CA UTION: • Use only the speakers of the SPEAKER IMPED ANCE indicated by ...
-
JVC RX-7040B - page 10
8 Placing speakers Fr ont speaker s (L/R) and center speak er (C) • Place these speak ers at the same height from the floor, a t or near ear le vel. • Array across the front of the vie wing area. Surround speak ers (LS/RS) and surround back speakers (SB) • Place these speak ers at a position which is 60 cm to 90 cm (2 ft to 3 ft) higher than ...
-
JVC RX-7040B - page 11
9 Connecting Audio/V ideo Components When connecting individual components, refer also to the manuals supplied with them. Analog connections If your audio components hav e digital audio output terminal, connecting them using the digital cords explained in “Digital Connections” (see page 12). By using this terminal, you can get better sound qual ...
-
JVC RX-7040B - page 12
10 V ideo component connections Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack. • If your video components ha ve S-video (Y/C-separation) and/or component video (Y , P B , P R ) terminals, connect them using an S- video ca ...
-
JVC RX-7040B - page 13
11 DVD player T o enjoy Dolby Digital and DTS multi-channel software (including Dual Mono software), connect the D VD player through the digital or analog discrete (D VD MUL TI) terminals. • When you connect a D VD player with stereo output jacks: Å To component video output ı To S-video output Ç To composite video output Î To left/right fron ...
-
JVC RX-7040B - page 14
12 Digital connections This receiv er is equipped with four DIGIT AL IN terminals—one digital coaxial terminal and three digital optical terminals—and one DIGIT AL OUT (optical) terminal on the rear . IMPORT ANT: • When connecting a D VD pla yer , VCR, digital TV broadcast tuner , or DBS tuner using the digital ter minals , you also need to c ...
-
JVC RX-7040B - page 15
13 Basic Operations The following operations are commonly used when you play any sound sources. Operations hereafter will be explained using the b uttons on the front panel. Y ou can also use the buttons on the remote control for the same functions if they ha ve the same and similar names/marks. Selecting the Source to Play Press one of the sour ce ...
-
JVC RX-7040B - page 16
14 Signal indicators Speaker indicators On the front panel On the remote Speaker and signal indicators on the display By checking the following indicators, you can easily conf irm which speakers you are acti vating and which signals are coming into this receiv er . What speaker indicators light depends on the speak er setting (for details, see “ ...
-
JVC RX-7040B - page 17
15 Selecting the Front Speakers When you ha ve connected two pairs of the front speakers, you can select which to use. T o use the speakers connected to the FR ONT SPEAKERS 1 terminals, press SPEAKERS ON/OFF 1 so that the SPEAKERS 1 indicator lights up on the display . • Make sure that the SPEAKERS 2 indicator is not lit. T o use the speakers con ...
-
JVC RX-7040B - page 18
16 Setting the Dynamic Range Y ou can enjoy a powerful sound at night using Midnight Mode. Press MIDNIGHT MODE so that “ MID NIGHT : 1 ” or “ MID NIGHT : 2 ” appear on the display . The MIDNIGHT MODE indicator also lights up. MID NIGHT : 1 Select w hen you w ant to r educe the dynamic range a little. MID NIGHT : 2 Select w hen you w ant to ...
-
JVC RX-7040B - page 19
17 T ur ning Analog Direct On and Off Y ou can enjoy the sound closer to the original source by overriding the sound adjustments such as Midnight Mode (see page 16), Bass Boost (see page 18), Equalization pattern (see page 28), speaker output le vel adjustments (see page 28), and Surround and DSP modes (see pages 30 to 35). Y ou can only adjust the ...
-
JVC RX-7040B - page 20
18 The f ollowing basic operations are possible only using the remote contr ol. Reinforcing the Bass Y ou can boost the bass level. • Once you hav e made an adjustment, it is memorized for each source. Press B ASS BOOST to boost the bass level. The B. BOOST indicator lights up on the display . • Each time you press the button, Bass Boost turns ...
-
JVC RX-7040B - page 21
19 Receiving Radio Br oadcasts Y ou can browse through all the stations or use the preset function to go immediately to a par ticular station. AUT O MUTING TUNED STEREO LINEAR PCM L R ANALOG VOLUME SPEAKERS 1 AUT O MUTING TUNED STEREO LINEAR PCM L R ANALOG VOLUME SPEAKERS 1 AUT O MUTING TUNED STEREO LINEAR PCM L R ANALOG VOLUME SPEAKERS 1 AUT O MUT ...
-
JVC RX-7040B - page 22
20 T o tune in to a pr eset station On the front panel: 1. Press FM or AM to select the band . The last recei ved station of the selected band is tuned in. 2. Press FM/AM PRESET 5 or ∞ until you f ind the channel y ou want. • Pressing FM/AM PRESET 5 increases the number . • Pressing FM/AM PRESET ∞ decreases the number . On the remote contro ...
-
JVC RX-7040B - page 23
21 Quick Speaker Setup Quick Speaker Setup helps you to easily and quickly register the speaker size and speaker distance according to your listening room to create the best possible surround effect. • Y ou can also register each speaker ’ s infor mation manually . For details, see page 23. Bef ore you start, r emember ... There is a time limit ...
-
JVC RX-7040B - page 24
22 Speakers (channels) number and the size Y ou can find how eac h of the speaker size is defined according to the number of connected speakers (speaker channel “ CH ” number) you select. • Subwoofer is counted as 0.1 channel. The size of connected speakers CH L/R C LS/RS SB SUBWFR 2.0CH LARGE NONE NONE NONE NO 2.1CH SMALL NONE NONE NONE YES ...
-
JVC RX-7040B - page 25
23 Setting the speakers T o obtain the best possible surround effect from the Surround and DSP modes, register the setting about the speak er ar rangement after all connections are completed. • If you hav e used Quick Speaker Setup on page 21, this setting is not required. 7 Subwoofer setting —SUB WOOFER Select whether you ha ve connected a sub ...
-
JVC RX-7040B - page 26
24 Setting the speaker distance The distance from your listening point to the speakers is another important element to obtain the best possible sound of the Surround and DSP modes. Set the distance from your listening point to the speakers. By referring to the speaker distance setting, this unit automatically sets the delay time of the sound throug ...
-
JVC RX-7040B - page 27
25 Setting for easy and effective surr ound operations 7 Auto Sur round —AUTO SURROUND Auto Surround works when the unit detects the incoming digital signal. In other words, it works... • When you select the digital source (the source with digital input selected for it), and • When you change the input mode from analog to digital. Select “ ...
-
JVC RX-7040B - page 28
26 7 For the DBS tuner —VIDEO IN DBS Select one of the f ollowing: VIDEO DBS: CMPNT * 2 Select when connecting the DBS tuner to the component video input jacks. VIDEO DBS: S/C Select when connecting the DBS tuner to the composite video or S-video input jacks. Notes: • If you ha ve selected “ CMPNT ” f or the component video setting for the ...
-
JVC RX-7040B - page 29
27 Adjusting Sound Y ou can make sound adjustment to your preference after completing basic setting. Basic Adjustment Items On the follo wing pages, you can adjust the items listed below: • Y ou can adjust only the items applicable to the current sound mode. • If Analog Direct is in use, y ou cannot make any sound adjustments. Items T o do See ...
-
JVC RX-7040B - page 30
28 Adjusting the speaker output levels Y ou can adjust the speaker output lev els. • Once you hav e made an adjustment, it is memorized for each source. 7 Adjustable speakers Y ou can adjust the following speakers ’ output lev els within the range of – 10 dB to +10 dB ( “ 0 (dB) ” is the initial setting): SUBWFR L VL Select to adjust the ...
-
JVC RX-7040B - page 31
29 Y ou can also use the remote control for adjusting the speaker output lev el and center tone. T o adjust the speaker output le vel: 1. Press TEST to check if you can hear the sounds thr ough all the speakers at equal lev el. T est tone comes out of the speakers in the following order . • No test tone comes out of the speakers for which the spe ...
-
JVC RX-7040B - page 32
30 Using the Sur r ound Modes This unit activates a variety of Surround modes automatically . The basic settings and adjustments stored (see pages 21 to 29) are applied. Reproducing Theater Ambience In a movie theater , many speak ers are located on the walls to reproduce impressiv e multi-surround sounds, reaching you from all directions. W ith th ...
-
JVC RX-7040B - page 33
31 DTS 96/24 In recent years, there has been increasing interest in higher sampling rates both for recording and for reproducing at home. Higher sampling rates allow wider frequenc y range and greater bit de pths provide e xtended dynamic range. DTS 96/24 is a multi-channel digital signal format (fs 96 kHz/24 bits) introduced by Digital Theater Sys ...
-
JVC RX-7040B - page 34
32 Surr ound Modes Applicable to the V arious Softwar e A vailable Surround modes v ary depending on the speaker settings and the incoming signals. The table belo w shows the relation of the Surround modes and the incoming signals (with the surround back speakers and EX/ES setting). • The numbers inside the parentheses follo wing the incoming sig ...
-
JVC RX-7040B - page 35
33 Activating the Surr ound Modes A vailable Surround modes v ary depending on the speaker settings and the incoming signals. (See page 32.) Activa ting one of the Surround modes for a sour ce automatically recalls the memorized settings and adjustments (see pag es 21 to 29). Y ou can also use the buttons on the remote control for the same function ...
-
JVC RX-7040B - page 36
34 : Suitable for audio sources : Suitable for video sources Using the DSP Modes This unit activates a variety of DSP modes automatically . The basic settings and adjustments stored (see pages 21 to 29) are applied automatically . Early reflections Reflections from behind Direct sounds Reproducing the Sound Field The sound heard in a concert hall, ...
-
JVC RX-7040B - page 37
35 LINEAR PCM DIGIT AL L SUBWFR LS RS CR DIGIT AL AU TO VOLUME DSP SPEAKERS 1 All channel stereo mode This mode can reproduce a larger stereo sound f ield using all the connected (and acti vated) speakers. • If the surround speak ers are set to “ NONE, ” you cannot select “ ALL STEREO. ” Mono Film In order to reproduce a more acoustic sou ...
-
JVC RX-7040B - page 38
36 Using the DVD MUL TI Playback Mode This receiver provides the DVD MUL TI playback mode for reproducing the analog discrete output mode of the DVD player . Activating the DVD MUL TI Playback Mode 1. Press D VD MUL TI so tha t “ DV D ” appears on the display . The MUL TI indicator also lights up. Note: When you select D VD MUL TI as the source ...
-
JVC RX-7040B - page 39
37 COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC ’ s audio components through the remote sensor on the receiver . Automatic Source Selection When you press the play ( 3 ) button on a connected component or on its own remote control, the recei ver automatically turns on and changes the source to t ...
-
JVC RX-7040B - page 40
38 A V COMPU LINK Remote Contr ol System The A V COMPU LINK remote control system allows you to operate JVC ’ s video components (TV , VCR, and DVD player) through the receiver . This receiv er is equipped with the A V COMPU LINK-III, which adds a function to operate JVC ’ s video components through the video components terminals. T o use this ...
-
JVC RX-7040B - page 41
39 Connecting procedur e 1. If y ou hav e already plugged your VCR , D VD player , TV and this receiv er into the A C outlets, unplug their A C power cords f irst. 2. Connect y our VCR, D VD player , TV and this recei ver , using the cables with the monaural mini- plugs (not supplied). • See “ CONNECTIONS 1 ” on the previous pag e . 3. Connec ...
-
JVC RX-7040B - page 42
40 Operating JVC ’ s Audio/V ideo Components Y ou can operate JVC ’ s audio and video components with this receiver ’ s r emote control, since control signals for JVC ’ s components are preset in the remote control. CD player After pressing CD, you can perform the following operations on the CD player: 3 : Start playing. 4 : Return to the b ...
-
JVC RX-7040B - page 43
41 CD r ecorder After pressing T APE/CDR (or T APE/CDR CONT), you can perform the following operations on a CD recorder: 3 : Start playing. 4 : Return to the beginning of the current (or pre vious) track. ¢ : Skip to the beginning of the ne xt track. 7 : Stop playing and recording. 8 : Pause playing or recording. T o resume, press 3 . REC P A USE: ...
-
JVC RX-7040B - page 44
42 Operating Other Manufactur ers ’ V ideo Equipment This remote control supplied with the receiver can transmit control signals for other manufacturers ’ TVs, CA TV conver ters, DBS tuners, VCRs and DVD players. When operating the other manufacturers ’ components, refer also to the manuals supplied with them. • After replacing batteries fo ...
-
JVC RX-7040B - page 45
43 T o change the transmittable signals for operating another manufacturer ’ s DVD player 1. Press and hold D VD . 2 Press D VD. 3. Enter a manufactur er ’ s code using b uttons 1 – 9, and 0. See the list on page 44 to find the code. 4. Release D VD . 5. T ry to operate y our D VD player by pressing DV D . When your D VD player turns on or of ...
-
JVC RX-7040B - page 46
44 Manufacturer Codes JVC 01 * Hitachi 02 Kenwood 03, 04 Magnavox 05 Marantz 06 Mitsubishi 07 Onkyo 08, 09 Panasonic 10 Philips 06 Pioneer 11 Proscan 12 RCA 12 Samsung 13 Sony 14 Toshiba 05 Yamaha 15 Zenith 05, 16 Manufacturers ’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment. Man ...
-
JVC RX-7040B - page 47
45 T r oubleshooting Use this char t to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC ’ s ser vice center . SOLUTION Plug the power cord into an AC outlet. Check speaker wiring and reconnect if necessary. (See page 7.) Press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 correctly. (See page 15.) S ...
-
JVC RX-7040B - page 48
46 Specifications Amplifier Output Po wer At Stereo Operation Front Channel: 130 W per channel, min. RMS, dri ven into 8 Ω , 20 Hz to 20 kHz, with no mor e than 0.08% total harmonic distortion. At Surround Operation Front Channel: 130 W per channel, min. RMS, dri ven into 8 Ω at 1 kHz, with no more than 0.8% total harmonic distortion. Center Ch ...
-
JVC RX-7040B - page 49
THIS LIMITED W ARRANTY IS V ALID ONL Y IN THE FIFTY (50) UNITED ST A TES, THE DISTRICT OF COLUMBIA AND IN COMMONWEAL TH OF PUER TO RICO. WHA T WE WILL DO: If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner . Such repair and replacement services shall be rendered by JVC during norm ...
-
JVC RX-7040B - page 50
BT -51002-5 (0301) QUALITY SER VICE HOW TO LOCA TE YOUR JVC SER VICE CENTER Dear Customer , In order to receive the most satisfaction from your purchase,please read the instruction booklet before operating the unit.In the event that repairs are necessary , please call 1 (800)537-5722 for your nearest authorized servicer or visit our website at www ...
-
JVC RX-7040B - page 51
EN 0104MWMMDWJEIN © 2004 VICTOR COMPANY OF JAPAN, LIMITED VICTOR COMPANY OF JAPAN, LIMITED RX-7040B/RX-7042S AUDIO/VIDEO CONTROL RECEIVER Cover_2_7040[J] 04.1.21, 15:54 2 ...
-
JVC RX-7040B - page 52
LVT1170-002A [C] RX-7040B/RX-7042S INSTR UCTIONS MANUEL D’INSTRUCTIONS A UDIO/VIDEO CONTR OL RECEIVER RECEPTEUR DE COMMANDE A UDIO/VIDEO English Fran ç ais Cover_7040[C] 04.2.12, 19:00 1 ...
-
JVC RX-7040B - page 53
G-1 CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. ATTENTION Afin d’éviter tout risque d’électrocution, d’incendie, etc.: 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil. 2. Ne pas exposer l’ ...
-
JVC RX-7040B - page 54
1 English T able of Contents Basic Settings ........................................... 21 Quick Speaker Setup ................................................................ 21 Basic Setting Items ................................................................... 22 Basic Procedure ................................................................ ...
-
JVC RX-7040B - page 55
2 English Intr oduction W e would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference. Featur es CC (Compression Compensative) conver ter CC Con verter eliminates jitter and ...
-
JVC RX-7040B - page 56
3 English Par ts Identification See pages in parentheses for details. 1 DIMMER button (18, 40) 2 Standby/On buttons (13, 40 – 43) A UDIO, DVD , CA TV/DBS , VCR , TV 3 Source selection b uttons (13 – 15, 19, 20, 36, 40 – 43) D VD MUL TI, D VD, CD*, T APE/CDR*, TV/DBS, VCR, FM/AM* * When you press one of these source selection buttons on the re ...
-
JVC RX-7040B - page 57
4 English Front Panel Press down on PUSH-OPEN. How to open the front door See pages in parentheses for details. 1 ST ANDBY/ON button and ST ANDBY lamp (13) 2 SPEAKERS ON/OFF 1/2 buttons (15) 3 SURR OUND button (32, 33) 4 Remote sensor 5 Display window (F or details, see “Display window” on the next page.) 6 Source selection b uttons (13 – 15, ...
-
JVC RX-7040B - page 58
5 English See pages in parentheses for details. 1 DU AL indicator (31) 2 AN ALOG indicator (16) 3 DIGIT AL A UTO indicator (16) 4 96/24 indicator (31) 5 MUL TI indicator (36) 6 NEO:6 indicator (31) 7 TUNED indicator (19) 8 PR O LOGIC indicator (30) PR O LOGIC II indicator (31) 9 STEREO indicator (19, 20) 0 A UTO MUTING indicator (20) - VIR TU AL SB ...
-
JVC RX-7040B - page 59
6 English Getting Star ted This section explains how to connect audio/video components and speakers to the receiver , and how to connect the power supply . Checking the Supplied Accessories Check to be sure you hav e all of the following items, which are supplied with the receiv er . The number in the parentheses indicates quantity of the pieces su ...
-
JVC RX-7040B - page 60
7 English Connecting the Speakers and Subwoofer Y ou can connect the following speakers: • T wo pairs of front speak ers. • One pair of surround speakers. • One surround back speaker or one pair of surround back speakers. • One center speaker . • One powered subwoofer . CA UTION: • Use only the speakers of the SPEAKER IMPED ANCE indicat ...
-
JVC RX-7040B - page 61
8 English Placing speakers Fr ont speaker s (L/R) and center speak er (C) • Place these speakers at the same height from the floor , at or near ear le vel. • Array across the front of the viewing area. Surround speak ers (LS/RS) and surround back speakers (SB) • Place these speakers at a position which is 60 cm to 90 cm higher than the listen ...
-
JVC RX-7040B - page 62
9 English Connecting Audio/V ideo Components When connecting individual components, refer also to the manuals supplied with them. Analog connections If your audio components hav e digital audio output terminal, connecting them using the digital cords explained in “Digital Connections” (see page 12). By using this terminal, you can get better so ...
-
JVC RX-7040B - page 63
10 English V ideo component connections Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack. • If your video components have S-video (Y/C-separation) and/or component video (Y , P B , P R ) terminals, connect them using an S- v ...
-
JVC RX-7040B - page 64
11 English DVD player T o enjoy Dolby Digital and DTS multi-channel software (including Dual Mono software), connect the D VD player through the digital or analog discrete (D VD MUL TI) terminals. • When you connect a D VD player with stereo output jacks: Å To component video output ı To S-video output Ç To composite video output Î To left/ri ...
-
JVC RX-7040B - page 65
12 English Digital connections This receiv er is equipped with four DIGIT AL IN terminals—one digital coaxial terminal and three digital optical terminals—and one DIGIT AL OUT (optical) terminal on the rear . IMPORT ANT: • When connecting a D VD pla yer , VCR, digital TV broadcast tuner , or DBS tuner using the digital ter minals , you also n ...
-
JVC RX-7040B - page 66
13 English Basic Operations The following operations are commonly used when you play any sound sources. Operations hereafter will be explained using the b uttons on the front panel. Y ou can also use the buttons on the remote control for the same functions if they ha ve the same and similar names/marks. Selecting the Source to Play Press one of the ...
-
JVC RX-7040B - page 67
14 English Selecting different sour ces for picture and sound While watching pictures from a video source, you can listen to sound of an audio source. • Once you hav e selected a video source, pictures of the selected source are sent to the TV until you select another video source. Press one of the audio sour ce selection buttons while viewing th ...
-
JVC RX-7040B - page 68
15 English Selecting the Front Speakers When you ha ve connected two pairs of the front speakers, you can select which to use. T o use the speakers connected to the FR ONT SPEAKERS 1 terminals, press SPEAKERS ON/OFF 1 so that the SPEAKERS 1 indicator lights up on the display . • Make sure that the SPEAKERS 2 indicator is not lit. T o use the spea ...
-
JVC RX-7040B - page 69
16 English Setting the Dynamic Range Y ou can enjoy a powerful sound at night using Midnight Mode. Press MIDNIGHT MODE so that “ MID NIGHT : 1 ” or “ MID NIGHT : 2 ” appear on the display . The MIDNIGHT MODE indicator also lights up. MID NIGHT : 1 Select w hen you w ant to r educe the dynamic range a little. MID NIGHT : 2 Select w hen you w ...
-
JVC RX-7040B - page 70
17 English T ur ning Analog Direct On and Off Y ou can enjoy the sound closer to the original source by overriding the sound adjustments such as Midnight Mode (see page 16), Bass Boost (see page 18), Equalization pattern (see page 28), speaker output le vel adjustments (see page 28), and Surround and DSP modes (see pages 30 to 35). Y ou can only ad ...
-
JVC RX-7040B - page 71
18 English The f ollowing basic operations are possible only using the remote contr ol. Reinforcing the Bass Y ou can boost the bass level. • Once you hav e made an adjustment, it is memorized for each source. Press B ASS BOOST to boost the bass level. The B. BOOST indicator lights up on the display . • Each time you press the button, Bass Boos ...
-
JVC RX-7040B - page 72
19 English Receiving Radio Br oadcasts Y ou can browse through all the stations or use the preset function to go immediately to a par ticular station. AUT O MUTING TUNED STEREO LINEAR PCM L R ANALOG VOLUME SPEAKERS 1 AUT O MUTING TUNED STEREO LINEAR PCM L R ANALOG VOLUME SPEAKERS 1 AUT O MUTING TUNED STEREO LINEAR PCM L R ANALOG VOLUME SPEAKERS 1 A ...
-
JVC RX-7040B - page 73
20 English T o tune in to a pr eset station On the front panel: 1. Press FM or AM to select the band . The last recei ved station of the selected band is tuned in. 2. Press FM/AM PRESET 5 or ∞ until you f ind the channel y ou want. • Pressing FM/AM PRESET 5 increases the number . • Pressing FM/AM PRESET ∞ decreases the number . On the remot ...
-
JVC RX-7040B - page 74
21 English Quick Speaker Setup Quick Speaker Setup helps you to easily and quickly register the speaker size and speaker distance according to your listening room to create the best possible surround effect. • Y ou can also register each speaker ’ s infor mation manually . For details, see page 23. Bef ore you start, r emember ... There is a ti ...
-
JVC RX-7040B - page 75
22 English Speakers (channels) number and the size Y ou can find how eac h of the speaker size is defined according to the number of connected speakers (speaker channel “ CH ” number) you select. • Subwoofer is counted as 0.1 channel. The size of connected speakers CH L/R C LS/RS SB SUBWFR 2.0CH LARGE NONE NONE NONE NO 2.1CH SMALL NONE NONE N ...
-
JVC RX-7040B - page 76
23 English Setting the speakers T o obtain the best possible surround effect from the Surround and DSP modes, register the setting about the speak er ar rangement after all connections are completed. • If you hav e used Quick Speaker Setup on page 21, this setting is not required. 7 Subwoofer setting —SUB WOOFER Select whether you ha ve connect ...
-
JVC RX-7040B - page 77
24 English Setting the speaker distance The distance from your listening point to the speakers is another important element to obtain the best possible sound of the Surround and DSP modes. Set the distance from your listening point to the speakers. By referring to the speaker distance setting, this unit automatically sets the delay time of the soun ...
-
JVC RX-7040B - page 78
25 English Setting for easy and effective surr ound operations 7 Auto Sur round —AUTO SURROUND Auto Surround works when the unit detects the incoming digital signal. In other words, it works... • When you select the digital source (the source with digital input selected for it), and • When you change the input mode from analog to digital. Sel ...
-
JVC RX-7040B - page 79
26 English 7 For the DBS tuner —VIDEO IN DBS Select one of the f ollowing: VIDEO DBS: CMPNT * 2 Select when connecting the DBS tuner to the component video input jacks. VIDEO DBS: S/C Select when connecting the DBS tuner to the composite video or S-video input jacks. Notes: • If you ha ve selected “ CMPNT ” f or the component video setting ...
-
JVC RX-7040B - page 80
27 English Adjusting Sound Y ou can make sound adjustment to your preference after completing basic setting. Basic Adjustment Items On the follo wing pages, you can adjust the items listed below: • Y ou can adjust only the items applicable to the current sound mode. • If Analog Direct is in use, y ou cannot make any sound adjustments. Items T o ...
-
JVC RX-7040B - page 81
28 English Adjusting the speaker output levels Y ou can adjust the speaker output lev els. • Once you hav e made an adjustment, it is memorized for each source. 7 Adjustable speakers Y ou can adjust the following speakers’ output lev els within the range of –10 dB to +10 dB (“0 (dB)” is the initial setting): SUBWFR L VL Select to adjust t ...
-
JVC RX-7040B - page 82
29 English Y ou can also use the remote control for adjusting the speaker output lev el and center tone. T o adjust the speaker output le vel: 1. Press TEST to check if you can hear the sounds thr ough all the speakers at equal lev el. T est tone comes out of the speakers in the following order . • No test tone comes out of the speakers for which ...
-
JVC RX-7040B - page 83
30 English Using the Sur r ound Modes This unit activates a variety of Surround modes automatically . The basic settings and adjustments stored (see pages 21 to 29) are applied. Reproducing Theater Ambience In a movie theater , many speak ers are located on the walls to reproduce impressiv e multi-surround sounds, reaching you from all directions. ...
-
JVC RX-7040B - page 84
31 English DTS 96/24 In recent years, there has been increasing interest in higher sampling rates both for recording and for reproducing at home. Higher sampling rates allow wider frequenc y range and greater bit de pths provide e xtended dynamic range. DTS 96/24 is a multi-channel digital signal format (fs 96 kHz/24 bits) introduced by Digital The ...
-
JVC RX-7040B - page 85
32 English Surr ound Modes Applicable to the V arious Softwar e A vailable Surround modes v ary depending on the speaker settings and the incoming signals. The table belo w shows the relation of the Surround modes and the incoming signals (with the surround back speakers and EX/ES setting). • The numbers inside the parentheses follo wing the inco ...
-
JVC RX-7040B - page 86
33 English Activating the Surr ound Modes A vailable Surround modes v ary depending on the speaker settings and the incoming signals. (See page 32.) Activa ting one of the Surround modes for a sour ce automatically recalls the memorized settings and adjustments (see pa ges 21 to 29). Y ou can also use the buttons on the remote control for the same ...
-
JVC RX-7040B - page 87
34 English : Suitable for audio sources : Suitable for video sources Using the DSP Modes This unit activates a variety of DSP modes automatically . The basic settings and adjustments stored (see pages 21 to 29) are applied automatically . Early reflections Reflections from behind Direct sounds Reproducing the Sound Field The sound heard in a concer ...
-
JVC RX-7040B - page 88
35 English LINEAR PCM DIGIT AL L SUBWFR LS RS CR DIGIT AL AU TO VOLUME DSP SPEAKERS 1 All channel stereo mode This mode can reproduce a larger stereo sound f ield using all the connected (and acti vated) speakers. • If the surround speaker s are set to “ NONE, ” you cannot select “ ALL STEREO. ” Mono Film In order to reproduce a more acou ...
-
JVC RX-7040B - page 89
36 English Using the DVD MUL TI Playback Mode This receiver provides the DVD MUL TI playback mode for reproducing the analog discrete output mode of the DVD player . Activating the DVD MUL TI Playback Mode 1. Press D VD MUL TI so tha t “ DV D ” appears on the display . The MUL TI indicator also lights up. Note: When you select D VD MUL TI as th ...
-
JVC RX-7040B - page 90
37 English COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC ’ s audio components through the remote sensor on the receiver . Automatic Source Selection When you press the play ( 3 ) button on a connected component or on its own remote control, the recei ver automatically turns on and changes the sou ...
-
JVC RX-7040B - page 91
38 English A V COMPU LINK Remote Contr ol System The A V COMPU LINK remote control system allows you to operate JVC ’ s video components (TV , VCR, and DVD player) through the receiver . This receiv er is equipped with the A V COMPU LINK-III, which adds a function to operate JVC ’ s video components through the video components terminals. T o u ...
-
JVC RX-7040B - page 92
39 English Connecting procedur e 1. If y ou hav e already plugged your VCR , D VD player , TV and this receiv er into the A C outlets, unplug their A C power cords f irst. 2. Connect y our VCR, D VD player , TV and this recei ver , using the cables with the monaural mini- plugs (not supplied). • See “ CONNECTIONS 1 ” on the previous pag e . 3 ...
-
JVC RX-7040B - page 93
40 English Operating JVC ’ s Audio/V ideo Components Y ou can operate JVC ’ s audio and video components with this receiver ’ s r emote control, since control signals for JVC ’ s components are preset in the remote control. CD player After pressing CD, you can perform the following operations on the CD player: 3 : Start playing. 4 : Return ...
-
JVC RX-7040B - page 94
41 English CD r ecorder After pressing T APE/CDR (or T APE/CDR CONT), you can perform the following operations on a CD recorder: 3 : Start playing. 4 : Return to the beginning of the current (or pre vious) track. ¢ : Skip to the beginning of the ne xt track. 7 : Stop playing and recording. 8 : Pause playing or recording. T o resume, press 3 . REC ...
-
JVC RX-7040B - page 95
42 English Operating Other Manufactur ers ’ V ideo Equipment This remote control supplied with the receiver can transmit control signals for other manufacturers ’ TVs, CA TV conver ters, DBS tuners, VCRs and DVD players. When operating the other manufacturers ’ components, refer also to the manuals supplied with them. • After replacing batt ...
-
JVC RX-7040B - page 96
43 English T o change the transmittable signals for operating another manufacturer ’ s DVD player 1. Press and hold D VD . 2 Press D VD. 3. Enter a manufactur er ’ s code using b uttons 1 – 9, and 0. See the list on page 44 to find the code. 4. Release D VD . 5. T ry to operate y our D VD player by pressing DV D . When your D VD player turns ...
-
JVC RX-7040B - page 97
44 English Manufacturer Codes JVC 01 * Hitachi 02 Kenwood 03, 04 Magnavox 05 Marantz 06 Mitsubishi 07 Onkyo 08, 09 Panasonic 10 Philips 06 Pioneer 11 Proscan 12 RCA 12 Samsung 13 Sony 14 Toshiba 05 Yamaha 15 Zenith 05, 16 Manufacturers ’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipm ...
-
JVC RX-7040B - page 98
45 English T r oubleshooting Use this char t to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC ’ s ser vice center . SOLUTION Plug the power cord into an AC outlet. Check speaker wiring and reconnect if necessary. (See page 7.) Press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 correctly. (See pag ...
-
JVC RX-7040B - page 99
46 English Specifications Amplifier Output Po wer At Stereo Operation Front Channel: 130 W per channel, min. RMS, dri ven into 8 Ω , 20 Hz to 20 kHz, with no more than 0.08% total harmonic distortion. At Surround Operation Front Channel: 130 W per channel, min. RMS, dri ven into 8 Ω at 1 kHz, with no more than 0.8% total harmonic distortion. Ce ...
-
JVC RX-7040B - page 100
EN, FR 0204MWMMDWJEIN © 2004 VICTOR COMPANY OF JAPAN, LIMITED VICTOR COMPANY OF JAPAN, LIMITED RX-7040B/RX-7042S AUDIO/VIDEO CONTROL RECEIVER Cover_7040[C] 04.2.12, 19:00 2 ...
Hai una domanda su JVC RX-7040B?
Utilizza il modulo sottostante
Se non hai risolto il problema con JVC RX-7040B con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con JVC RX-7040B è probabile che voglia condividere il modo di risolverlo.