Italiano dropdown-ico

Manuale per l’uso QSC ISIS 215SB

42 pagine 2.57 mb
Scarica

Vai alla pagina of 42

Summary
  • QSC ISIS 215SB - page 1

    1 User Manual TD-000105-00 rev .B *TD-000105-00* ISIS 215SB ISIS 215PCM 2 x 15” W eather-Resistant Subwoofer Cabinet with Speakon™ Input C onnec tor Integra ted, Self-Po wered—Self-Processed, Industrial S ystems 3000 W att P ow ered S ubwoofer and 3600 Wa t t , 2-channel “ T op Box ” amplifier , Computer Configurable DSP f or each Amplifi ...

  • QSC ISIS 215SB - page 2

    2 © Copyright 2002, QSC Audio Products, Inc. QSC® is a registered trademark of QSC Audio Products, Inc. “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office All trademarks are the property of their respective owners. Speakon™ is a registered trademark of Neutrik Inc., Lakewood, NJ IMPORT ANT SAFETY PRECAUTIONS &a ...

  • QSC ISIS 215SB - page 3

    3 INTRODUCTION General Overview ...........................................................................................4 T echnical Overview ........................................................................................6 Block Diagram.................................................................................................7 UNP ...

  • QSC ISIS 215SB - page 4

    4 INTRODUCTION- General Overview Introduction Thank you and congratulations on your purchase of the ISIS 215PCM Powered-System Control Module or 215SB Subwoofer . This product represents the state-of-the-art in all-weather , lightweight SR (sound reinforcement) loudspeaker systems. The “215” marks the introduction of QSC’ s ISIS loudspeaker s ...

  • QSC ISIS 215SB - page 5

    5 INTRODUCTION- General Overview T ransporting the 215PCM using integral wheels and handles. 215PCM Front A 16” length of “L-track” flying hardware is featured on all four corners of the cabinet. Pole cups are featured for either cabinet orientation. One, shown, on the shorter side, and two on the longer . 215PCM Rear Rubber feet are featured ...

  • QSC ISIS 215SB - page 6

    6 INTRODUCTION- T echnical Overview T echnical Overview: CH1 and CH2 Inputs are connected to the T op Box Processor and to the Mode Switch. In Combination Mode, the Mode Switch connects CH1 and CH2 Inputs to the Subwoofer Processor as well. In Discrete Mode, CH1 and CH2 Inputs are disconnected from the Subwoofer Processor , and Input 3 is used to f ...

  • QSC ISIS 215SB - page 7

    7 INTRODUCTION- Block Diagram ...

  • QSC ISIS 215SB - page 8

    8 The 215PCM is highly durable and is carefully packaged and crated. We recommend you inspect the unit carefully after removing it from the packaging, as occasionally there may be damage due to some unfortunate incident during shipment. Report any damage to the shipping carrier . W e recommend saving the carton and packing material. It is always a ...

  • QSC ISIS 215SB - page 9

    9 Install the Signal Manager software on the PC that will be used to configure the 215PCMs processors. See page 20. Put the 215PCM in a location that: • ....is close enough to the PC to connect the serial cable. •....has 120V , 30A service to power the 215PCM. •....has enough room to make connections or adjustments. Plug in the 215PCM. See pa ...

  • QSC ISIS 215SB - page 10

    10 Adjusting the Gain Settings of the Amplifiers PREP ARA TION FOR FIRST USE- Amplifier Gain Controls Ordinarily , the Gain controls of the amplifiers are left set at full gain. This is not recommended for first-time users of freely- configurable DSP . Freely configurable DSP , while being the most flexible and desirable, will do precisely what the ...

  • QSC ISIS 215SB - page 11

    11 The 215PCM requires 120 V olt, 30 Amp AC service. Attempting full power operation on lower rated circuits may overheat wirirng and cause breakers to switch off. Use only heavy-duty 12 or 10 ga. extension cords. The 215PCM requires a 120 V olt, 30 Amp connection to the AC mains. The power connectors used are to be NEMA L5-30, or equivalent. The s ...

  • QSC ISIS 215SB - page 12

    12 T o Configure a Processor (215PCM only) Each Processor has a 9-pin “D-sub” connector labeled RS-232. The RS-232 connection is used to configure the Processor by connecting to the PC’ s COM port. Important points: – The 215PCM must be ON (powered up) in order to configure the Processors. – Each Processor is configured individually . – ...

  • QSC ISIS 215SB - page 13

    13 CONNECTIONS- Mode Switch and Signal Routing The position of the Mode Switch determines how the input signals are routed. Select your operating mode before making connections. If you are using the DataPorts for audio input, the Mode Switch has no effect. Refer to the diagram, below . COMBINA TION MODE– Use CH1 and CH2 Inputs OR Input 3 (mono). ...

  • QSC ISIS 215SB - page 14

    14 Audio Connections Audio inputs can be connected to the XLR inputs OR the DataPort connections (QSControl users). This section provides information on using the XLR Inputs, For DataPort information see page 17. CONNECTIONS- Audio Connections: XLR Inputs CH1 and CH2 INPUT - In Combination Mode, use these for 2-channel inputs. For mono input, use I ...

  • QSC ISIS 215SB - page 15

    15 XLR Connections The XLR inputs are electronically balanced. T o maintain the benefits of balanced, pro-audio connections, make all connections to the 215PCM using balanced, high-quality cable and connectors. If balanced inputs are not available, use a unbalanced-to-balanced converter , such as a “DI” box or proper audio transformer . Unbalan ...

  • QSC ISIS 215SB - page 16

    16 CONNECTIONS- Post Processor Outputs Post Processor Outputs Each processor has two post-processor outputs. They are labeled CH1 OUTPUT and CH2 OUTPUT . The audio present at these outputs is processed and the signal is the same as at the OUT1 and OUT2 blocks in the Signal Manager software. See Block Diagram, page 7, for details. These are electron ...

  • QSC ISIS 215SB - page 17

    17 CONNECTIONS- DataPort (QSControl users only) When using the DataPort connections for audio inputs, do not use the XLR audio inputs. Any signals present on both connections will be summed, producing unexpected results. It is OK to use the XLRs for audio input if the DataPort connection is used only for control and monitoring. Use only QSC Audio D ...

  • QSC ISIS 215SB - page 18

    18 CONNECTIONS- Output to T op Boxes (Speakons™) Output to T op Boxes At the right side of the rear panel are the output connections to the top box speakers. Note the color coding scheme of the text labels for each Speakon connector . The color coding corresponds with the colors of the Mode Switch labels (Combination Mode or Discrete Mode). The u ...

  • QSC ISIS 215SB - page 19

    19 USE- Cooling Air Inlet and Exhaust V ents The 215PCM contains two forced-air cooled QSC Powerlight 2-series amplifiers. They are mounted within the back portion of the enclosure. The amplifi- ers rely upon an unobstructed air flow in and out of the respective vents, shown below . Keep these air vents free of obstructions and dust buildup. Be cer ...

  • QSC ISIS 215SB - page 20

    20 USE- AC Power Switch and LED Indicators LED Indicators Each Processor has two LED indicators, PWR and SIGNAL. The indicators are located on the rear panel of the 215PCM. PWR- When the 215PCM is connected to a properly rated and working AC supply circuit and is turned on, the blue PWR LED on each of the Processors will illuminate. When the system ...

  • QSC ISIS 215SB - page 21

    21 IMPORT ANT USER CAUTION USE- LED Indicators (continued) and Important User Caution The 215PCM has been equipped with a very powerful internal amplifier . The amplifier power is several times greater than the long-term power capacity of the drivers. This allows the full capacity of the speakers to be used without reaching the clipping point of th ...

  • QSC ISIS 215SB - page 22

    22 PROCESSOR USE- Software Installation and System Requirements 1. Insert the QSC Signal Manager CD into your drive (typically drive “D:”). If your computer has AUTORUN enabled, the installation will start automatically after several seconds. If it does not, then proceed to step 2, below . Otherwise, skip to step 3. 2. Select Run from the Windo ...

  • QSC ISIS 215SB - page 23

    23 PROCESSOR USE: General Guidelines and Preset Description NOTE! The factory setting for all eight Preset memories is wire- through. Signals are passed from input to output without any processing. Each Processor must be configured as desired by the user . Y ou may select configurations from the sample files (*.cfg) within Signal Manager or create ...

  • QSC ISIS 215SB - page 24

    24 Each Processor must be loaded with your desired signal processing configu- ration using the Signal Manager program before use. T est all new configura- tions for expected behavior at low power levels to avoid inadvertently damaging speaker systems. Each Processor has eight Preset memories numbered 1 through 8. Presets are DSP configurations save ...

  • QSC ISIS 215SB - page 25

    25 Processor Use: Configuring the Processors (Discrete 2.1) How the Processors are configured is dependant on the system setup and desired results. For example, a discrete 2.1 system requires a different signal chain than a mono 3-way stack. Decide how your system will be set up before starting to configure the Processors. The following are example ...

  • QSC ISIS 215SB - page 26

    26 Example 1- Discrete 2.1 (continued) The Subwoofer Processor is next. In Discrete Mode, the Subwoofer Processor’ s input signal comes from the Input 3 XLR. Input 3 is routed to the Subwoofer Processor’ s IN1 block (see example, below). The IN2 block is not placed when operating in Discrete Mode. An example of a typical Subwoofer configuration ...

  • QSC ISIS 215SB - page 27

    27 Processor Use: Configuring the Processors (3-way Mono Stack) Example 2- Active 3-way Mono Stack In a 3-way configuration, the T op Box amplifier’ s two channels are used for low- and high-frequencies and the subwoofer handles bass. The Processors perform the required crossover and time delay functions. This T op Box configuration has time dela ...

  • QSC ISIS 215SB - page 28

    28 TROUBLESHOOTING The 215PCM “cuts-out” when I really crank it up (intermittent operation)- • Make sure the AC power source is rated for 120V , 30 Amps. Do not use 20 or 15 Amp AC supply circuits for the 215PCM! Use only 12 or 10 gauge heavy-duty extension cords. • If the AC power source is “sagging” (or drooping) under heavy load, the ...

  • QSC ISIS 215SB - page 29

    29 TROUBLESHOOTING Unable to “talk” to processor from Signal Manager software (OFFLINE status indicated)- • Check that the serial cable is a normal serial data cable. Null-modem type cables will not work. • Make sure that the serial cable is properly connected on both ends and that the retaining screws are snug (finger tight). • V erify A ...

  • QSC ISIS 215SB - page 30

    30 TROUBLESHOOTING I am using the 215PCM setup for biamp operation, but my mid- and high-frequency sound seems to be gone- • Make sure the Mode Switch is in the correct position for your intended application. • Be sure you are using only the upper Speakon for 4-wire biamp connection. • If using 2-wire Speakon cables to connect to your biamp c ...

  • QSC ISIS 215SB - page 31

    31 Specifications- ISIS 215SB SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Dimensions ...

  • QSC ISIS 215SB - page 32

    32 Specifications- ISIS 215SB Acoustic Performance SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE ...

  • QSC ISIS 215SB - page 33

    33 Specifications- ISIS 215SB 215SB Specifications Frequency Range Recommended Bandpass: 35- 150 Hz (±3 dB) Frequency Response: 36- 360 Hz (-3dB) Usable Frequency Range: 29- 440 Hz (-10 dB) Maximum Output Calculated Peak Output 1 : 141 dB SPL Measured Continuous Output 2 : 131 dB SPL Continuous Noise Exposure Level 3 : 122 dBA Impedance: 4 ohms (n ...

  • QSC ISIS 215SB - page 34

    34 Specifications- ISIS 215PCM SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Self-Powered Dimensions ...

  • QSC ISIS 215SB - page 35

    35 Specifications- ISIS 215PCM 215PCM System Specification Description 215 PCM: Comprised of the 215SB Subwoofer Cabinet with a “backpack” containing two QSC DSP-3 24-bit Signal Processors, 1 ruggedized QSC PL230 3000 Watt amplifier and 1 ruggedized QSC PL236 3600 Watt amplifier. All interconnections for the audio signals and AC power are compl ...

  • QSC ISIS 215SB - page 36

    36 A mplifier Specifications Output Power in watts Subwoofer Amplifier (PL230 type) 4 Ohms, 1 kHz, 1% THD 3000 Watts Top Box Amplifier (PL236 type) FTC: 8 Ohms per channel (20- 20 kHz., 0.03% THD) 725 Watts 4 Ohms per channel (20- 20 kHz., 0.05% THD) 1100 Watts EIA: 1 kHz @ 1% THD 8 Ohms per channel 800 Watts 4 Ohms per channel 1300 Watts 2 Ohms pe ...

  • QSC ISIS 215SB - page 37

    37 Specifications- ISIS 215PCM Processors Note: Specifications are subject to change without notice. Digital Signal Processor Specifications Type Freely configurable, custom DSP with software for PC. Computer connection needed only for set up. Signal Processing Two QSC DSP-3 Processors, 24 bit, 48 kHz., one for each amplifier Frequency response at ...

  • QSC ISIS 215SB - page 38

    38 APPENDIX- Contact Closure Wiring Details Contact Closure Feature The contact closure feature is used to trigger gain changes in the DSP . Any configuration that uses one or more switched gain objects (see Signal Manager software Help file ) can take advantage of this feature. The contact closure will trigger all switched gain objects at once. Al ...

  • QSC ISIS 215SB - page 39

    39 Pin Signal Description 1 DCD 2 T D 3 R D 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 Contact Closure RS-232 Pinout: The diagram below shows the pin assignments for the female RS-232 connector on the DSP-3 Processors featured in the 215PCM. *Note! Pin 9 is used for contact closure input. This pin is not normally used by RS-232 devices. Some laptop and deskto ...

  • QSC ISIS 215SB - page 40

    40 Disclaimer QSC Audio Products, Inc. is not liable for any damage to amplifiers, or any other equipment that is caused by negligence or improper installation and/or use of this speaker product. Product Warranty QSC Audio Products, Inc. (“QSC”) guarantees its products to be free from defective material and / or workmanship for a period o f thr ...

  • QSC ISIS 215SB - page 41

    41 ...

  • QSC ISIS 215SB - page 42

    42 QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office. ©2001 QSC Audio Products, Inc. ...

Fabbricante QSC Categoria Speaker

I documenti che otteniamo dal fabbricante del dispositivoQSC ISIS 215SB possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici QSC
- manuali per l’uso ISIS 215SB
- schede prodotto QSC
- opuscoli
- o etichette energetiche QSC ISIS 215SB
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso QSC ISIS 215SB.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione QSC ISIS 215SB, manuali di manutenzione, brevi manuali o manuali utente QSC ISIS 215SB. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto QSC ISIS 215SB.

Manuali per l’uso simili

Manuale completo del dispositivo QSC ISIS 215SB, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare QSC ISIS 215SB dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti QSC ISIS 215SB.

Il manuale per l’uso completo QSC, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale QSC ISIS 215SB - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice QSC ISIS 215SB, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per QSC ISIS 215SB che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo QSC ISIS 215SB - che ci dovrebbe aiutare nei primi passi durante l'uso QSC ISIS 215SB
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del QSC ISIS 215SB
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio QSC ISIS 215SB in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su QSC ISIS 215SB?

Utilizza il modulo sottostante

Se non hai risolto il problema con QSC ISIS 215SB con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con QSC ISIS 215SB è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)