Manuale per l’uso Asus LS99

34 pagine 0.39 mb
Scarica

Vai alla pagina of 34

Summary
  • Asus LS99 - page 1

    Chapter 1 Introduction 1 1. Introduction The ASUS LS99 LAN/SCSI card can only be installed on a motherboard with an ASUS proprietary expansion slot. See 2.3 Installing the ASUS LAN/SCSI card for location of this slot. The ASUS LS99 LAN/SCSI card enables you to connect up to 30 SCSI devices— such as very large arrays of high-performance HDDs, exte ...

  • Asus LS99 - page 2

    2 Chapter 1 Introduction 1. Introduction 1.2 Product Features The ASUS LS99 LAN/SCSI card has two independent SCSI channels, each with a maximum throughput of 160 MBytes/sec. SCSI Channel A has two internal connectors (CHA-WIDE and SCSI-50). SCSI Channel B has one internal connector (CHB-WIDE) and one external connector (CHBEXTWIDE). ® Internal Na ...

  • Asus LS99 - page 3

    Chapter 2 Hardware Installation 3 2. HW Installation Discharge any static electricity build-up before handling your LAN/SCSI card by touching a grounded metal object (like the exposed metal parts on the back of your computer). Remove the ASUS LS99 Dual Channel LAN/SCSI card from the pack- ing and check that it is not damaged. CAUTION: Static charge ...

  • Asus LS99 - page 4

    4 Chapter 2 Hardware Installation 2. HW Installattion 2.2 LAN/SCSI card Settings 1) SCSI Contr oller Setting (SCSI_EN) This jumper allows you to enable/disable the SCSI controller function. The default setting is Enable . SCSI Controller Setting 123 123 Disable Enable SCSI_EN SCSI_EN LAN_EN ® LAN_EN 2) LAN Contr oller Setting (LAN_EN) (only on mod ...

  • Asus LS99 - page 5

    Chapter 2 Hardware Installation 5 2. HW Installation 2.3 Installing the ASUS LAN/SCSI card 1. Locate the ASUS proprietary expansion slot. 2. Remove the expansion slot cover on the back of the computer aligned with the ASUS proprietary expansion slot. Save the slot cover screw . 3 . Carefully insert the ASUSCONNECT edge connection of the ASUS LS99 L ...

  • Asus LS99 - page 6

    6 Chapter 2 Hardware Installation 2. HW Installattion 2.5 Setting Up SCSI Devices There are several things to do before you connect your SCSI devices to the ASUS LS99 LAN/SCSI card: • Check the SCSI IDs • Set the termination • Connect the power cables Since setup can vary from device to device, always refer to the device ’ s documentation f ...

  • Asus LS99 - page 7

    Chapter 2 Hardware Installation 7 2. HW Installation Determine the SCSI ID of each device on the SCSI bus. Note any duplications. Make any necessary changes to the SCSI IDs and record the IDs for future reference. The following table is provided as a place to keep this record. 2.5.2 SCSI ID Record SCSI ID SCSI Device Channel A SCSI Device Channel B ...

  • Asus LS99 - page 8

    8 Chapter 2 Hardware Installation 2. HW Installattion 2.6 Connecting Devices Y ou can connect a total of 30 SCSI devices to the ASUS LS99 LAN/SCSI card, with up to 15 devices on each SCSI channel. Before connecting devices, be sure to review 2.5 Setting Up SCSI Devices . 2.6.1 Connecting Internal Ultra160 and Ultra2 Devices A special 68-pin L VD ca ...

  • Asus LS99 - page 9

    Chapter 2 Hardware Installation 9 2. HW Installation 3. Plug additional internal Ultra160 and Ultra2 SCSI devices to the other cable connectors, starting with the connector at the terminated end of the cable. Make sure to match pin-1 on all connections. NOTE: Internal Ultra160 and Ultra2 SCSI devices come from the factory with termination disabled ...

  • Asus LS99 - page 10

    10 Chapter 2 Hardware Installation 2. HW Installattion 2.6.3 Connecting Ultra/Fast Narrow SCSI Devices If you have internal Ultra/Fast Narrow SCSI devices with standard 50-pin connectors, you can connect them to the 50-pin internal SE Narrow SCSI connector . Follow these steps to connect the devices: 1. Locate the provided 50-pin internal Ultra/Fas ...

  • Asus LS99 - page 11

    Chapter 2 Hardware Installation 11 2. HW Installation Follow these steps to connect external SCSI devices: 1. Connect one end of the external SCSI cable to the external Ultra160 connector . 2. Connect the other end of the cable to a SCSI connector on the back of an external device. Pin-1 must match on all connections. If you are installing only one ...

  • Asus LS99 - page 12

    12 Chapter 2 Hardware Installation 2. HW Installattion 2.6.7 Connecting to the Network A connector is available (only on model with LAN) to allow connection to a Local Area Network (LAN) through a network hub. Fast Ethernet Port Connector (RJ45) ® ...

  • Asus LS99 - page 13

    Chapter 3 Configuring the ASUS LS99 13 3. Configuration 3 Configuring the ASUS LS99 3.1 Configuring the Motherboard BIOS T o access the motherboard BIOS setup program, press <Delete> during POST . Onboard LAN Boot ROM [Disabled] Leave on default setting. Configuration options: [Disabled] [Enabled] ONB SCSI BIOS First [No] Setting this field t ...

  • Asus LS99 - page 14

    14 Chapter 3 Configuring the ASUS LS99 3. Configuration 3.2 Configuring Using SCSI Select SCSI Select , which is included with the ASUS LS99 SCSI Card, enables you to change SCSI settings without opening the computer or handling the card. SCSI Select also enables you to low-level format or verify the disk media of your SCSI hard disk drives. The fo ...

  • Asus LS99 - page 15

    Chapter 3 Configuring the ASUS LS99 15 3. Configuration SCSI Select Options A vailable Settings Default Setting SCSI Bus Interface Definitions SCSI Controller ID 0-15 7 SCSI Controller Parity Enabled Disabled Disabled SCSI Controller T ermination: Ch. A 1 Enabled Enabled Disabled Ch. B Enabled Enabled Disabled Y T ype Connection (T ermination Disab ...

  • Asus LS99 - page 16

    16 Chapter 3 Configuring the ASUS LS99 3. Configuration 3.2.1 Starting SCSI Select Follow these steps to start SCSI Select: 1. T urn on or restart your computer . During the startup process, pay careful attention to the messages that appear on your screen. 2. When the following message appears on your screen, press the <Ctrl> + <A> keys ...

  • Asus LS99 - page 17

    Chapter 3 Configuring the ASUS LS99 17 3. Configuration Advanced Options Boot Device Configuration • Boot SCSI Controller — (Default: A First) Specifies which of the two SCSI channels the boot device is connected to (if the computer boots from a SCSI device). If you change this setting, the change automatically applies to both SCSI channels. ? ...

  • Asus LS99 - page 18

    18 Chapter 3 Configuring the ASUS LS99 3. Configuration The following options have no effect if the SCSI Card BIOS is disabled. (The SCSI Card BIOS is normally enabled by default.) • BIOS Multiple LUN Support — (Default: No) Leave this setting on No if the device does not have multiple Logical Unit Numbers (LUNs). When set to Ye s , the SCSI ca ...

  • Asus LS99 - page 19

    Chapter 3 Configuring the ASUS LS99 19 3. Configuration • SCSI Controller Int 13 Support — (Default: Enabled) Enables or disables the SCSI card BIOS. If you change this setting, the change automatically applies to both SCSI channels. • Leave on Enabled to enable the SCSI card BIOS and allow it to scan and initialize all SCSI devices. • Set ...

  • Asus LS99 - page 20

    20 Chapter 3 Configuring the ASUS LS99 3. Configuration 3.2.4 Using SCSI Disk Utilities T o access the SCSI disk utilities, follow these steps: 1. Select the SCSI Disk Utilities option from the menu that appears after starting SCSI Select .SCSI Select scans the SCSI bus (to determine the devices installed) and displays a list of all SCSI IDs and th ...

  • Asus LS99 - page 21

    Chapter 4 Installing SCSI Drivers 21 4. Driver Installation 4 Installing SCSI Drivers 4.1 Windows 95/98 T o install W indows 98 from your CD-ROM drive, you will need to update the W indows 95/98 startup disk that came with your W indows 98 CD. Y ou need to do this on a system that has DOS, W indows 95, or W indows 98 already installed. 1. Create a ...

  • Asus LS99 - page 22

    22 Chapter 4 Installing SCSI Drivers 4. Driver Installation 4.2 Windows NT The adpu160m.sys driver is not embedded on the W indows NT 4.0 installation disks (or CD-ROM) and must be added during W indows NT installation. Fresh Windows NT 4.0 Installation From Floppy Disk 1. Create the W indows NT driver disk. T o create the W indows NT driver disk: ...

  • Asus LS99 - page 23

    Chapter 5 T roubleshooting 23 5. T roubleshooting 5.1 T roubleshooting Checklist Most problems with using the ASUS LS99 SCSI Card result from errors in preparing and connecting devices on the SCSI bus. If you have problems, check these items first. NOTE: If you have problems with a specific SCSI device when other connected SCSI devices are working ...

  • Asus LS99 - page 24

    24 Chapter 5 T roubleshooting 5. T roubleshooting When I start W indows 95/98, the system locks up when the W indows logo is displayed. How can I get the system to start so that I can verify that the SCSI card is functioning normally? 1. Start or restart your computer . 2. (For W indows 95:) When the message “ Starting W indows 95 ” appears, pr ...

  • Asus LS99 - page 25

    Chapter 5 T roubleshooting 25 5. T roubleshooting An “X” inside a red circle appears with the ASUS LS99 SCSI card software driver in Device Manager . What does this mean? It means that the ASUS LS99 SCSI Card software driver is disabled and isn ’ t loading. T o enable the driver 1. Double-click the ASUS LS99 SCSI card software driver in Devic ...

  • Asus LS99 - page 26

    26 Chapter 5 T roubleshooting 5. T roubleshooting 6. The setting and the hardware using the setting are displayed. • If a specific resource is not listed, the resource is not used by a device. • If a resource is listed more than once,the resource is used by more than one device. • If a resource is used by an unknown device, the resource is us ...

  • Asus LS99 - page 27

    Appendix 27 Appendix A SCSI (pronounced “ scuzzy ” ) stands for Small Computer Systems Interface. SCSI is an industry standard computer interface for connecting SCSI devices (such as a hard disk drive, CD-ROM drive, or scanner) to a common SCSI bus. A SCSI bus is an electrical pathway that consists of a SCSI adapter card (such as the ASUS LS99 ...

  • Asus LS99 - page 28

    28 Appendix Appendix A • If you are booting your computer from a SCSI hard disk drive connected to the ASUS LS99 SCSI Card, the Boot SCSI ID setting in the SCSISelect utility must correspond to the SCSI ID of the device from which you are booting. By default, the Boot SCSI ID is set to 0. W e recommend that you do not change this setting. • In ...

  • Asus LS99 - page 29

    Appendix 29 Appendix A Using SCSI Devices Using SCSI Hard Disk Drives • If you connect a SCSI hard disk drive to the ASUS LS99 SCSI card that was previously connected to a dif ferent SCSI card, you must low-level format the drive before you can use it. Back up the data on the drive before you format it! (See 3.2.4 Using SCSI Disk Utilities for in ...

  • Asus LS99 - page 30

    30 Appendix Appendix A Maximum Cable Lengths The total length of cabling (internal and external) on the SCSI bus cannot exceed the maximum lengths listed in the following table. The third column lists the maximum number of SCSI devices you can connect to the SCSI card. Maximum Maximum Devices Cable Length Data Transfer Rate Supported 25 m (82.0 ft) ...

  • Asus LS99 - page 31

    Glossary 31 Glossary G Glossary Addr ess - A specific location in memory , designated either numerically or by a symbolic name. Asynchr onous Data T ransfer - A method of transmission which does not require a common clock, but separates fields of data by stop and start bits. It is slower than synchronous data transfer . BIOS - Basic Input/Output Sy ...

  • Asus LS99 - page 32

    32 Glossary Glossary EISA - Extended Industry Standard Architecture. An extension of the 16-bit ISA bus standard. It allows devices to perform 32-bit data transfers. External SCSI Device - A SCSI device installed outside the computer cabinet. These devices are connected in a continuous chain using specific types of shielded cables. Fast SCSI - A st ...

  • Asus LS99 - page 33

    Glossary 33 Glossary NVRAM - Non V olatile Random Access Memory . Actually an EEPROM (Electronically- Erasable Programmable Read Only Memory chip) used to store configuration information. See EEPROM. Operating System - A program that organizes the internal activities of the computer and its peripheral devices. An operating system performs basic tas ...

  • Asus LS99 - page 34

    34 Glossary Glossary SCSI ID - A way to uniquely identify each SCSI device on the SCSI bus. Each SCSI bus has eight available SCSI IDs numbered 0 through 7 (or 0 through 15 for W ide SCSI). The host adapter usually gets ID 7 giving it priority to control the bus. SDMS - SCSI Device Management System. An ASUS software product that manages SCSI syste ...

Fabbricante Asus Categoria Network Card

I documenti che otteniamo dal fabbricante del dispositivoAsus LS99 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Asus
- manuali per l’uso LS99
- schede prodotto Asus
- opuscoli
- o etichette energetiche Asus LS99
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Asus LS99.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Asus LS99, manuali di manutenzione, brevi manuali o manuali utente Asus LS99. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Asus LS99.

Manuali per l’uso simili

Manuale completo del dispositivo Asus LS99, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Asus LS99 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Asus LS99.

Il manuale per l’uso completo Asus, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Asus LS99 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Asus LS99, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Asus LS99 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Asus LS99 - che ci dovrebbe aiutare nei primi passi durante l'uso Asus LS99
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Asus LS99
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Asus LS99 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Asus LS99?

Utilizza il modulo sottostante

Se non hai risolto il problema con Asus LS99 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Asus LS99 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)