Italiano dropdown-ico

Manuale per l’uso Weider 831.159730

32 pagine 1.5 mb
Scarica

Vai alla pagina of 32

Summary
  • Weider 831.159730 - page 1

    ® USER’S MANUAL Model No. 831.159730 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference. Serial Number Decal Patent Pending Visit our website at www .weid ...

  • Weider 831.159730 - page 2

    2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly . . . . . . . . . . . ...

  • Weider 831.159730 - page 3

    3 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 80 in. Depth: 55 in. Low Pulley Station Foot Plate Leg Lever Press Arms Backrest Curl Pad Butterfly Arms Ab Pulley Station Weight Stacks Leg Press Lever Thank you for selecting the innovative and versatile WEIDER ® PRO 9940 Home Gym. The WEIDER ® PRO 9940 offers a unique selection of weight stations d ...

  • Weider 831.159730 - page 4

    4 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual. Place the chart on the floor or work table and use it to quickly identify different parts as you open the pack- ...

  • Weider 831.159730 - page 5

    1. Before beginning, make sure that you have read and understood the information on page 4. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” See drawing 1a. Press a 2” Square Inner Cap (28) into each end of the Butterfly Base (4). Press two 2” Square Inner Caps (28) into the Weight Base (5). Insert four 5/16” x 2 1/2” Carriage ...

  • Weider 831.159730 - page 6

    3. Place the bracket on the lower end of the Butterfly Upright (1) over the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the Butterfly Base (4). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts. Do not tighten the Nylon Locknuts yet. 3 6 4. Press three 2” Square Inner Caps (28) into the Butterfly T op Frame (33). Press two 1” ...

  • Weider 831.159730 - page 7

    7. Press a 1” Square Inner Cap (98) into the small tube on the Press Upright (2). Place the bracket on the lower end of the Press Upright (2) over the indicated 5/16” x 2 1/2” Carriage Bolts (92) in the Press Base (6). Hand tighten two 5/16” Nylon Locknuts (64) onto the Bolts. Do not tighten the Nylon Locknuts yet. Place the bracket on the ...

  • Weider 831.159730 - page 8

    8 10. Lubricate the 3/8” x 3” Bolt (88). Attach the Leg Press Lever (83) to the Press Base (6) with the Bolt and a 3/8” Nylon Locknut (50). Do not overtighten the Nylon Locknut; the Leg Press Lever must pivot easily . 10 1 1. Place two Weight Bumpers (51) over the indicated holes in the Weight Base (5). Slide a W eight Guide (15) into each of ...

  • Weider 831.159730 - page 9

    9 14. Attach the Weight T op Frame (66) to the Press T op Frame (9) with one 3/8” x 2 3/4” Bolt (46), a Support Plate with 4” center holes (94), and a 3/8” Nylon Locknut (50). Slide a 3 1/2” Pulley (24) with a Cable T rap (25) onto a 3/8” x 4” Bolt (78). Insert the Bolt through the Support Plate (94) and hand tighten a 3/8” Nylon Lo ...

  • Weider 831.159730 - page 10

    15 15. Attach each of the four Weight Guides (15) to the Weight T op Frame (66) with a 3/8” x 3 3/4” Bolt (59), a 3/8” Flat W asher (48), and a 3/8” Nylon Locknut (50). Important: Go back and fully tighten all Nylon Locknuts used in steps 1 through 15. 10 16 48 59 59 15 48 15 50 50 17. Press a 1 3/4” Square Inner Cap (35) into the top of ...

  • Weider 831.159730 - page 11

    11 20. Locate and open the parts bag labeled “PULLEY BAG 2.” Remove one “V”-Pulley (27) from the bag. Leave the remaining pulleys in the bag for identification of the Pro Pulley . Wrap the Butterfly Cable (73) around a “V”-Pulley (27) in the direction shown. Attach the “V”-Pulley and a Large Cable T rap (32) to the bracket on the ba ...

  • Weider 831.159730 - page 12

    12 23. Attach the Butterfly Cable (73) to the bracket on the Right Butterfly Arm (1 1) with a 3/8” x 1” Bolt (84) and two 3/8” Nylon Jamnuts (63). Note: The loop on the Cable and the two Nylon Jamnuts must be mount- ed underneath the welded bracket. 23 84 11 63 73 Bracket 24. Identify the Ab Cable (74). It is approximately 224” long, and it ...

  • Weider 831.159730 - page 13

    13 26. Wrap the Ab Cable (74) around a 3 1/2” Pulley (24) in the direction shown. Attach the Pulley to the Small Pulley Bracket (22) with a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50). Make sure the Pulley Bracket is oriented as shown. 26 25. Remove both 3 1/2” Pulleys (24) from the pre-assem- bled Adjustable Pulley Plates (23). ...

  • Weider 831.159730 - page 14

    14 29. Wrap the Ab Cable (74) around a 4 1/2” Pulley (82) in the direction shown. Attach the Pulley inside the indi- cated bracket on the Weight T op Frame (66) with a 3/8” x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50). Make sure the threaded end of the Ab Cable is routed through the bracket, as shown. 28. Wrap the Ab Cable (74) around a ...

  • Weider 831.159730 - page 15

    15 31. Remove a Pro Pulley (26) from the bag labeled “PULLEY BAG 2”. Identify the Low Pulley Cable (75). It is approximately 143 1/2” long and it has a ball on one end and a loop on the other . Route the end with the loop through the slot in the cable guide on the Butterfly Base (4). Route the Low Pulley Cable (75) under a Pro Pulley (26) as ...

  • Weider 831.159730 - page 16

    16 35 75 46 48 48 63 35. Attach the loop on the end of the Low Pulley Cable (75) to the indicated hole in the Small Leg Lever (41) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat W ashers (48), and a 3/8” Nylon Jamnut (63). 36. Remove a Pro Pulley (26) from the bag labeled “PULLEY BAG 2”. Identify the Press Cable (72). It is approximately ...

  • Weider 831.159730 - page 17

    17 39. Important: Although the following steps are not difficult to perform, the correct routing of the cable is critical to the functioning of the home gym. Please make sure that you wrap the cable around the pulleys exactly as shown in each step. Route the Press Cable (72) through the opening in the Press Frame (8), and wrap the Cable around a 3 ...

  • Weider 831.159730 - page 18

    18 43. Wrap the Press Cable (72) around a 3 1/2” Pulley (24) in the direction shown. Attach the Pulley and a Cable T rap (25) to the indicated hole on the far side of the Leg Press Lever (83) with a 3/8” x 4 3/4” Bolt (60) and a 3/8” Nylon Jamnut (63). Note: Thread the Jamnut only two turns onto the Bolt; you will later attach another Pulle ...

  • Weider 831.159730 - page 19

    19 47. Route the threaded end of the Press Cable (72) around the 3 1/2” Pulley (24) that was mounted on the bracket on the Weight Base (5) in an earlier step. 47 24 5 72 48. Wrap the Press Cable (72) over a 4 1/2” Pulley (82) in the direction shown. Attach the Pulley inside the indicated bracket on the Weight T op Frame (66) with a 3/8” x 1 3 ...

  • Weider 831.159730 - page 20

    20 Seat Assembly 50. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach the Backrest (12) to the indicated holes in the Butterfly Upright (1) with two 1/4” x 2 1/2” Bolts (79) and two 1/4” Flat W ashers (71). 50 79 79 1 12 71 51. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the center hole in a Seat Plate (65). Atta ...

  • Weider 831.159730 - page 21

    21 Miscellaneous Assembly 52. Insert a 1/4” x 2 1/2” Carriage Bolt (45) through the center hole in a Seat Plate (65). Attach the Seat Plate to a Seat (13) with two 1/4” x 3/4” Bolts (49). Insert the 1/4” x 2 1/2” Carriage Bolt (45) into the indi- cated hole in the Butterfly Seat Frame (14) and secure it with a 1/4” Flat W asher (71) a ...

  • Weider 831.159730 - page 22

    22 56 56. Apply the WEIDER PRO 9940 decal in the location shown. Important: The warning decals shown below have been attached to the home gym in the locations shown. If a decal is missing or illegible, please call our customer hotline at the number on the front cover of this manual to order a replacement decal. Apply the new decal in the appropriat ...

  • Weider 831.159730 - page 23

    23 Cable Diagrams The Cable Diagrams below and on the next page show the proper routing of the Butterfly Cable (73), the Ab Cable (74), the Low Pulley Cable (75) and the Press Cable (72). The numbers show the correct route for each Cable. Make sure that the Cables are routed correctly , that the Pulleys move smoothly , and that the Cable T raps do ...

  • Weider 831.159730 - page 24

    24 14 2 1 5 15 13 6 9 3 7 11 4 8 10 12 Press Cable (72) ...

  • Weider 831.159730 - page 25

    25 Adjusting the Leg Press Plate T o adjust the position of the Leg Press Plate (55), pull out the Lock Pin (91) and slide the Adjustment T ube (90) backwards or forwards in the bracket on the Leg Press Lever (83). Line up one of the adjustment holes in the Adjustment T ube with the hole in the bracket and re-insert the Lock Pin. 91 83 90 55 Attach ...

  • Weider 831.159730 - page 26

    26 Slack can be removed form the Press Cable (72) by moving one or both of the “V”-Pulleys (27) on the Press Cable. One “V”-Pulley (27) is attached to the small tube on the Press Upright (2). There are three free holes in the small tube, and you can move the “V”-Pulley to any one of them to tighten the cables. Start by moving the “V? ...

  • Weider 831.159730 - page 27

    27 The threaded ends on the Press Cable (72) and the Ab Cable (74) that are attached to the weight stacks can also be used to tighten the cables. T o tighten the Ab Cable (74), remove the “U”-Bracket (97) from the Short Weight Tube (17) by removing the 5/16” x 1 3/4” Bolt (96) and the 5/16” Nylon Locknut (64). T ighten the 1/4” Nylon Lo ...

  • Weider 831.159730 - page 28

    3/4" Round Inner Cap (43) 1” Retainer Ring (31) 1" Round Outer Cap (38) 1" Square Inner Cap (98) 1 3/4" Square Inner Cap (35) 1" Round Inner Cap (76) 1" Round Inner Cap (86) 2" Square Inner Cap (28) ...

  • Weider 831.159730 - page 29

    3/8" Nylon Locknut (50) 3/8" Nylon Jamnut (63) 3/8" x 3 1/2" Bolt (56) 5/16" Nylon Locknut (64) 3/8" x 4 3/4" Bolt (60) 1” T ap Screw (80) 3/8" x 2 3/4" Bolt (46) 3/8" x 2" Bolt (54) 1/4" Flat W asher (71) 5/16" x 1 3/4" Bolt (96) 3/8" Flat W asher (48) 1/4" x 3/4&quo ...

  • Weider 831.159730 - page 30

    Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part List—Model No. 831.159730 R0800A Key No. Qty . Description Key No. Qty . Description 1 1 Butterfly Upright 2 1 Press Upright 3 1 Support Frame 4 1 Butterfly Base 5 1 Weight Base 6 1 Press Base 7 1 Press Seat Frame 8 1 Press Frame 9 1 Press T ...

  • Weider 831.159730 - page 31

    46 57 57 59 59 24 50 24 46 78 56 60 59 87 62 52 50 87 64 64 25 63 24 89 92 92 95 64 64 30 30 43 51 89 80 25 24 54 62 63 50 24 25 50 88 24 60 63 25 24 92 92 101 102 89 87 64 71 79 68 50 24 57 22 57 50 24 67 58 81 69 50 24 47 74 65 49 45 71 79 71 79 12 71 79 99 64 27 32 62 48 50 64 92 97 21 19 89 28 28 28 28 76 28 64 32 27 98 68 39 39 61 63 75 72 84 ...

  • Weider 831.159730 - page 32

    Part No. 158051 R0800A Printed in Canada © 1999 Sears, Roebuck and Co. SEARS, ROEBUCK AND CO., HOFFMAN EST A TES, IL 60179 Model No. 831.159730 QUESTIONS? If you find that: • you need help assembling or operating the WEIDER ® PRO 9940 Home Gym • a part is missing • or you need to schedule repair service call our toll-free HELPLINE 1-800-736 ...

Fabbricante Weider Categoria Home Gym

I documenti che otteniamo dal fabbricante del dispositivoWeider 831.159730 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Weider
- manuali per l’uso 831.159730
- schede prodotto Weider
- opuscoli
- o etichette energetiche Weider 831.159730
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Weider 831.159730.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Weider 831.159730, manuali di manutenzione, brevi manuali o manuali utente Weider 831.159730. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Weider 831.159730.

Manuali per l’uso simili

Manuale completo del dispositivo Weider 831.159730, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Weider 831.159730 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Weider 831.159730.

Il manuale per l’uso completo Weider, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Weider 831.159730 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Weider 831.159730, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Weider 831.159730 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Weider 831.159730 - che ci dovrebbe aiutare nei primi passi durante l'uso Weider 831.159730
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Weider 831.159730
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Weider 831.159730 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Weider 831.159730?

Utilizza il modulo sottostante

Se non hai risolto il problema con Weider 831.159730 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Weider 831.159730 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)