Italiano dropdown-ico

Manuale per l’uso Arrow Plastic HM108-A

32 pagine 0.85 mb
Scarica

Vai alla pagina of 32

Summary
  • Arrow Plastic HM108-A - page 1

    * Size rounded off to the nearest foot BUILDING DIMENSIONS CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES WHEN HANDLING METAL PARTS. 709291207 Model No. EN108-A HM108-A MN10 ...

  • Arrow Plastic HM108-A - page 2

    2 Owner's Manual Bef ore beginning constr uction, check local b uilding codes regarding f ootings, location and other requirements. Study and understand this owner's manual. Impor tant inf or mation and helpful tips will make y our constr uction easier and more enjo ya ble . Assembly Instructions: Instructions are supplied in this manual ...

  • Arrow Plastic HM108-A - page 3

    3 Selecting and Preparing Y our Site: Bef ore assemb ly , y ou will want to decide on a location f or your b uilding. The best location is a le v el area with good drainage. •Allow enough working space for ease of moving parts into position during assembly. Be sure there will be enough space at entrance for doors to open fully and enough space ar ...

  • Arrow Plastic HM108-A - page 4

    4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your build- ing. •Practice caution with the tools b ...

  • Arrow Plastic HM108-A - page 5

    Finish: F or long lasting finish, per iodically clean and wax the e xter ior surf ace. T ouch- up scratches as soon as you notice them on your unit. Immediately clean the area with a wire br ush; wash it and apply touch-up paint per manuf acturer's recommendation. Roof: K eep roof clear of leav es and snow with long handled, soft-bristled broo ...

  • Arrow Plastic HM108-A - page 6

    ACCESSORIES.... A6 WEB 6 * Some drilling required to fit buildings without mid-wall bracing. Model No. SS404 • Makes 8" to 12" (20-30cm) wide shelves in any length. • Brackets, braces, hardware included. Lumber is not included. Model No. SS900-A • Grey color • 3 shelves • Holds up to 85 lbs. (38kg) (even weight distribution) Hea ...

  • Arrow Plastic HM108-A - page 7

    THIS P AGE WA S LEFT BLANK INTENTIONALL Y 7 ...

  • Arrow Plastic HM108-A - page 8

    THIS P AGE WA S LEFT BLANK INTENTIONALL Y 8 ...

  • Arrow Plastic HM108-A - page 9

    The Foundation For Y our Building 9 FRONT (DOOR) FRONT (DOOR) Foundation A09 Note: Finished Slab dimensions, with lumber removed. OPTION 1: ARROW FLOOR FRAME KIT : (Order No. FB109-A or 68385-A) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one of the following: A. ...

  • Arrow Plastic HM108-A - page 10

    It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring Down The Building Anchoring A10 Arrow Anchoring Kit: (Model No. AK100 or 68383) Recommended for use with the concrete foundation. Contains: Corner gussets, perimeter clips, hardware, 1/4" masonary drill bit ...

  • Arrow Plastic HM108-A - page 11

    11 Remove from bag of screws and save for the last step 67293 Weather Stripping (1) 5971 Roof Beam Bracket (4) 66382 Lower Door Guide (4) 66183 Roof Trim Cap (2 right & 2 left) 66045 Handle (2) 66646 Washer (377) (10 sheets of 40) 65109 #8-32 Acorn Nut (4) (Packed with Screws) 67468 Peak Cap (2) (Arrow Logo) 65004 #8Ax5/16" Screw (328) 659 ...

  • Arrow Plastic HM108-A - page 12

    Parts List A12 12 Assembly P a r t P a r t Quantity Check K ey No . Number Description i n C a rto n List 1 3719 Door Handle Brace 2 2 9364 W all P anel (Side) 4 3 9372 F ront W all P anel 2 4 9365 F ront W all Channel 2 5 5986 Rear W all Angle 2 6 6000 Right Gable 2 7 6001 Left Gable 2 8 10497 Horizontal Door Brace 4 9 9355 V e r tical Door Brace ...

  • Arrow Plastic HM108-A - page 13

    13 Assembly by Key No. A13 1 1 2 2 2 2 3 3 4 4 5 5 6 6 7 7 8 8 8 8 9 9 10 11 12 12 12 12 12 12 13 13 14 14 15 16 17 17 17 17 18 18 19 19 20 20 21 21 22 22 23 24 24 24 24 24 24 24 24 25 25 26 26 26 26 27 27 27 27 28 29 30 30 31 31 32 32 32 32 33 33 33 33 11 ...

  • Arrow Plastic HM108-A - page 14

    The front floor frame is made up of three pieces. The side floor frames and the rear floor frame are made up of two pieces. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show the proper overall length for the sides, rear and front. Proceed as follows: 1 Place the front fl ...

  • Arrow Plastic HM108-A - page 15

    S tep 2 A15 15 ● P ar ts Needed F or ● Frame Assemblies The main frame pieces reinforce the walls. These pieces will later be in- stalled in the center and at the top edge of the side walls and the rear wall. Proceed as follows: 1 Overlap the rear wall channel pieces as shown in the figure and fasten the two pieces together with one bolt in the ...

  • Arrow Plastic HM108-A - page 16

    16 The roof beams join the two gables and support the roof panels. The main roof beam is made up of four pieces overlapped back to back at the cen- ter. The left and right roof beam as- semblies are made up of two pieces. Hint: These pieces are force-fitted, so you may have to press hard to join them together. 1 Place the end of one roof beam insid ...

  • Arrow Plastic HM108-A - page 17

    17 NOTE: Door Track Splice (painted part) S tep 4 A17 ● P ar ts Needed F or ● Door T rack Assembly ● ● ● ● ● 6403 Door Track Splice (1) ● ● ● ● ● 9366 Door Track (2) 66769 STEP 3 118 1/8" 3m STEP 4 END VIEW STEP 1 9366 STEP 2 6403 9366 Long Leg on Top Short Leg on Bottom 9366 9366 6403 66769 118 1/8" 3m 118 1/8&quo ...

  • Arrow Plastic HM108-A - page 18

    ● ● ● ● ● Front Floor Assembly (1) ● ● ● ● ● Side Floor Assembly (2) ● ● ● ● ● Rear Floor Assembly (1) ● P ar ts Needed F or ● Floor Frame S tep 5 A18 The floor frame must be square and level or holes will not align. 18 1 Assemble the four corners of the floor frame using two screws at each corner as shown. At the ...

  • Arrow Plastic HM108-A - page 19

    1 Position a corner panel at the corner of the floor frame as shown. The widest part of each corner panel must be placed along the side of the building for all four corners. Fasten the corner panel to the floor frame with one screw. Support the corner panel with a step ladder until a wall panel is attached. 2 Attach the front wall panels to the fro ...

  • Arrow Plastic HM108-A - page 20

    The main frame pieces give rigidity to the side walls and provide a surface for attaching the gables which sup- port the roof. 1 Fasten the rear wall angle as- sembly across the inside top of the rear wall using screws. 2 Fasten the rear wall channel as- sembly across the middle of the rear wall using screws. 3 Fasten the side wall angles across th ...

  • Arrow Plastic HM108-A - page 21

    S tep 8 A21 ● P ar ts Needed F or ● W all Panels ● ● ● ● ● 9364 Wall Panel (4) ● ● ● ● ● 8995 Wall Panel (4) The wall panels come in two widths. Each wall panel has a crimped rib on one side. The crimped rib should go under the rib of the panel that follows it. 1 Locate all of the wall panels and set each one alongside the b ...

  • Arrow Plastic HM108-A - page 22

    ● ● ● ● ● 9900 Door Jamb (2) ● ● ● ● ● 9365 Front Wall Channel (2) ● P ar ts Needed F or ● Front Channel/Door Jamb S tep 9 A22 The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs. 1 Fasten the front wall channels in their positions between the end of the side wall ...

  • Arrow Plastic HM108-A - page 23

    23 The gables go on top of the front and rear walls to support the roof beams. NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. 1 Attach the four roof beam brackets to the gables using two bolts, washers and nuts. NOTE Mounting leg of bracket must face toward center of gable a ...

  • Arrow Plastic HM108-A - page 24

    ● P ar ts Needed F or ● Gables/Braces S tep 1 1 A24 ● ● ● ● ● Left Gable Assemblies (2) ● ● ● ● ● Right Gable Assemblies (2) ● ● ● ● ● 6635 Gable Brace (2) 24 1 Lift and fasten a right and left gable, under angle at corner, to the door track and rear wall angle with screws. Hint: On the rear gable, use a bolt and n ...

  • Arrow Plastic HM108-A - page 25

    25 S tep 12 A25 ● P ar ts Needed F or ● Roof Beams ● ● ● ● ● Main Roof Beam (1) ● ● ● ● ● Single Roof Beam (2) 1 Spread the two halves of the main roof beam and fasten the roof beam to the gable brace of the front gable. 2 Fasten the other end of the main roof beam to the gable brace of the rear gable. 3 Fasten the single ro ...

  • Arrow Plastic HM108-A - page 26

    26 S tep 13 A26 ● P ar ts Needed F or ● Right Roof Panel ● ● ● ● ● 8468 Right Roof Panel (1) Installing the roof panels is best done with a step ladder. Begin installing roof panels at the back right corner of the building. Each screw and bolt in the roof requires a washer. NOTE Measure the building diagonally again and make adjustmen ...

  • Arrow Plastic HM108-A - page 27

    1 Install a left roof panel at the left rear and right front corner of the roof. Install a right roof panel at the left front corner of the roof. 3 Install 2 narrow and 2 wide roof panels in the sequence and posi- tions shown on previous page. Do not fasten the lower end of the panels to the side wall angles at this time. Continue weather stripping ...

  • Arrow Plastic HM108-A - page 28

    28 S tep 15 A28 ● P ar ts Needed F or ● Ridge Caps & Panels ● ● ● ● ● 8840 Ridge Cap (1) ● ● ● ● ● 7483 Roof Panel (2) ● ● ● ● ● 8486 Ridge Cap (1) 1 Install the first ridge cap on the completed roof section using bolts and nuts. Fasten roof panel overlaps not used for ridge cap. Cover the head of bolt with the ...

  • Arrow Plastic HM108-A - page 29

    1 Attach the right and left side roof trim to the lower end of the roof pan- els on each side of the building using screws at each panel overlap. NOTE A single screw fastens both trim pieces at the overlap. 2 Using your thumb and index fin- ger, overbend the bottom flange of the roof panel rib at the corner inward enough so the right and left roof ...

  • Arrow Plastic HM108-A - page 30

    30 ● ● ● ● ● 3719 Door Handle Brace (2) ● ● ● ● ● 10489 Right and Left Doors (2) ● ● ● ● ● 10497 Horizontal Door Brace (4) ● ● ● ● ● 9355 Vertical Door Brace (2) ● P ar ts Needed F or ● Door Assembly S tep 17 A30 The steps on this page tell how to assemble the right door. You will perform exactly the same ...

  • Arrow Plastic HM108-A - page 31

    31 S tep 18 A31 ● P ar ts Needed F or ● Door Installation & Adjustment ● ● ● ● ● Right Door Assembly (1) ● ● ● ● ● Left Door Assembly (1) 1 From inside the building, put the bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the front frame track. 2 Position the top of ...

  • Arrow Plastic HM108-A - page 32

    SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protec ...

Fabbricante Arrow Plastic Categoria Outdoor Storage

I documenti che otteniamo dal fabbricante del dispositivoArrow Plastic HM108-A possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Arrow Plastic
- manuali per l’uso HM108-A
- schede prodotto Arrow Plastic
- opuscoli
- o etichette energetiche Arrow Plastic HM108-A
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Arrow Plastic HM108-A.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Arrow Plastic HM108-A, manuali di manutenzione, brevi manuali o manuali utente Arrow Plastic HM108-A. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Arrow Plastic HM108-A.

Manuali per l’uso simili

Manuale completo del dispositivo Arrow Plastic HM108-A, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Arrow Plastic HM108-A dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Arrow Plastic HM108-A.

Il manuale per l’uso completo Arrow Plastic, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Arrow Plastic HM108-A - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Arrow Plastic HM108-A, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Arrow Plastic HM108-A che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Arrow Plastic HM108-A - che ci dovrebbe aiutare nei primi passi durante l'uso Arrow Plastic HM108-A
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Arrow Plastic HM108-A
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Arrow Plastic HM108-A in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Arrow Plastic HM108-A?

Utilizza il modulo sottostante

Se non hai risolto il problema con Arrow Plastic HM108-A con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Arrow Plastic HM108-A è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)