-
Mercury SR-10K Mag-Stripe Access System - page 1
Doc. 10107-0007 Rev 1.04 Page 1 Mercury Security Corporation, © 2005 SR-10K SR-10K Mag-Stripe Access System Users Guide ...
-
Mercury SR-10K Mag-Stripe Access System - page 2
Doc. 10107-0007 Rev 1.04 Page 2 Mercury Security Corporation, © 2005 SR-10K Table of Contents Section Page Overview 3 Quick S tart and Configuration Planning 5 Programming Guide 6 Operating Mode S pecifications 10 Mode 1: Basic Access Control with Door Monitoring 10 Mode 2: Restricted Access Control with Door Monitoring 1 1 Mode 3: Access Control ...
-
Mercury SR-10K Mag-Stripe Access System - page 3
Doc. 10107-0007 Rev 1.04 Page 3 Mercury Security Corporation, © 2005 SR-10K Description The SR-10K is a complete stand-alone access controller , using either magnetic-stripe cards or cipher (keypad) codes for identifying valid users. The Card Reader with Keypad and the Interface Module are the SR-10K system's major components. Separating the ...
-
Mercury SR-10K Mag-Stripe Access System - page 4
Doc. 10107-0007 Rev 1.04 Page 4 Mercury Security Corporation, © 2005 SR-10K Cipher Codes The SR-10K supports up to 10 cipher codes. Each code is one to six digits in length - shorter codes are terminated with the '#' key . Cipher codes, like cards, are assigned a User Level, and like cards, may cause different output relay action dependi ...
-
Mercury SR-10K Mag-Stripe Access System - page 5
Doc. 10107-0007 Rev 1.04 Page 5 Mercury Security Corporation, © 2005 SR-10K Quick Start The factory default setting enables the SR-10K to be used immediately , without any further programming, using the 10 cards shipped with the unit. The database is set to Random Mode, and the cards are enrolled as Level 1 users in slots 01 through 10. Additional ...
-
Mercury SR-10K Mag-Stripe Access System - page 6
Doc. 10107-0007 Rev 1.04 Page 6 Mercury Security Corporation, © 2005 SR-10K SR-10K Programming Guide The COMMAND ENTR Y MODE is selected by passing a valid MASTER card through the reader . The intergral keypad allows direct data entry on the SR-10K. The "*" key is used to start a new command entry . The ' # ' key terminates fie ...
-
Mercury SR-10K Mag-Stripe Access System - page 7
Doc. 10107-0007 Rev 1.04 Page 7 Mercury Security Corporation, © 2005 SR-10K CIPHER CODES Related Commands (Commands 15 through 17) Up to 10 cipher codes may be defined (user slots 0 through 9). Each cipher code may be from 1 to 6 digits long. Cipher codes shorter than 6 digit s are terminated with the "#" key . Just like cards can produc ...
-
Mercury SR-10K Mag-Stripe Access System - page 8
Doc. 10107-0007 Rev 1.04 Page 8 Mercury Security Corporation, © 2005 SR-10K Command 33 - Set the Auxiliary Relay Pulse Time (Output K2) *3 3 - select Command 33 0-9 0-9 - select the pulse time for Output K2: 00 to 99 seconds (+1/2 second) Configuration Settings (Commands 31through 34) Command 32 - Set the Door Strike Relay Pulse Time (Output K1) * ...
-
Mercury SR-10K Mag-Stripe Access System - page 9
Doc. 10107-0007 Rev 1.04 Page 9 Mercury Security Corporation, © 2005 SR-10K Command 91 - Set a New MASTER Card *9 1 - select Command 91 1 or 2 - select which Master Card to change: 1 or 2 new card - read the card to set as the new Master Card Usage notes: 1 - The second Master Card slot is provided for administrative convenience in cases where the ...
-
Mercury SR-10K Mag-Stripe Access System - page 10
Doc. 10107-0007 Rev 1.04 Page 10 Mercury Security Corporation, © 2005 SR-10K Description Access Control with Door Monitoring provides for basic access control and door use annunciation. A downward read of all valid User Cards pulse Output K1, the strike control relay. The upward read of a Level 2 card toggles the strike control relay, in effect pe ...
-
Mercury SR-10K Mag-Stripe Access System - page 11
Doc. 10107-0007 Rev 1.04 Page 11 Mercury Security Corporation, © 2005 SR-10K Description Restricted Access Control with Door Monitoring restricts Level 1 user access based on the status of Input I2 and provides door use annunciation on Output K2. Level 1 cards are accepted only if the Input I2 sees a closed contact. Level 2 or 3 cards are not depe ...
-
Mercury SR-10K Mag-Stripe Access System - page 12
Doc. 10107-0007 Rev 1.04 Page 12 Mercury Security Corporation, © 2005 SR-10K Operating Mode 03: Access Control and Alarm Panel Control Description The Access Control and Alarm Panel Control configuration provides for basic access control and gives some users the ability to send a pulse to arm and disarm alarm panels. Both a downward and an upward ...
-
Mercury SR-10K Mag-Stripe Access System - page 13
Doc. 10107-0007 Rev 1.04 Page 13 Mercury Security Corporation, © 2005 SR-10K Operating Mode 04: Restricted Access Control and Alarm Panel Control Description Restricted Access Control and Alarm Panel Control provides restricts Level 1 user access based on the status of Input I2 and it gives some users the ability to arm/disarm alarm panels. Level ...
-
Mercury SR-10K Mag-Stripe Access System - page 14
Doc. 10107-0007 Rev 1.04 Page 14 Mercury Security Corporation, © 2005 SR-10K Operating Mode 05: "Supervisor" Restricted Access Control Description This mode allows Level 2 cards to toggle Output K2, which, connected back to Input I2, restricts Level 1 users. In this mode, Level 1 cards are accepted only if Input I2 sees a closed contact. ...
-
Mercury SR-10K Mag-Stripe Access System - page 15
Doc. 10107-0007 Rev 1.04 Page 15 Mercury Security Corporation, © 2005 SR-10K Description Access Control with Door Bell Control operates just like Mode 1, with an additional feature for using Output K2 for annunciation. This mode was created for applications where Output K2 is configured to drive a door bell/ buzzer. A valid Level 1 user or a Reque ...
-
Mercury SR-10K Mag-Stripe Access System - page 16
Doc. 10107-0007 Rev 1.04 Page 16 Mercury Security Corporation, © 2005 SR-10K +− Installation Find a suitable location to anchor the reader mounting bracket. The mounting of the reader does not require a junction box. However, rigid conduit is required for outdoor application. A single gang junction box may used to provide transition to rigid con ...
-
Mercury SR-10K Mag-Stripe Access System - page 17
Doc. 10107-0007 Rev 1.04 Page 17 Mercury Security Corporation, © 2005 SR-10K Maintenance The SR-10K readers are designed to provide continuous service with minimal routine maintenance. However, contaminants (such as magnetic oxides from badges and dirt) tend to accumulate on the read head. Without regular cleaning, these contaminants will shorten ...
-
Mercury SR-10K Mag-Stripe Access System - page 18
Doc. 10107-0007 Rev 1.04 Page 18 Mercury Security Corporation, © 2005 SR-10K 1.4 [36] 2.9 [74] 3.25 [83] 2 X Ø0.1 8 [4.5] HOLES 2.0 [50] 5.5 [140] 1.3 [33] 3.3 [84] 2.6 [66 ] Reader and Interface Dimensions Reader to Interface Connection: Connect the Reader to the Interface Module using the straight 6-conductor modular cable. DO NOT use cross- ov ...
-
Mercury SR-10K Mag-Stripe Access System - page 19
Doc. 10107-0007 Rev 1.04 Page 19 Mercury Security Corporation, © 2005 SR-10K Addendum - Revision C This revision changed the door module to accommodate screw mounting instead of using snap track. The new module dimension is 4.25 x 2.75 inches. Connection to the card reader is also changed from modular jack to a screw terminals for more convenient ...
Hai una domanda su Mercury SR-10K Mag-Stripe Access System?
Utilizza il modulo sottostante
Se non hai risolto il problema con Mercury SR-10K Mag-Stripe Access System con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Mercury SR-10K Mag-Stripe Access System è probabile che voglia condividere il modo di risolverlo.