-
Bunn TU3Q - page 1
TU3Q Q U IC K BR E W OPERA TING & SERVICE MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www .bunnomatic.com 10288.0000N 03/04 ©1988 Bunn-O-Matic Corporation ...
-
Bunn TU3Q - page 2
Page 2 CONTENTS User Notices .................................................................... 3 Electrical & Plumbing Requirements ............................... 4 Initial Set-Up .................................................................... 5 Auto Sweetener Set-Up .................................................... 5 Adjusting Brew ...
-
Bunn TU3Q - page 3
Page 3 00831.0000F 3/98 ©1988 BUNN-O-MA TIC CORPORATION READ THE ENTIRE OPERA TING MANU AL BEFORE BUYING OR USING THIS PR ODUCT THIS APPLIANCE IS HEA TED WHENEVER CONNECTED T O A POWER SOURCE F AILURE TO COMPL Y RISKS EQUIPMENT D AMAGE, FIRE, OR SHOCK HAZARD Fill water tank before turning -on thermostat or connecting appliance to power sour ce . U ...
-
Bunn TU3Q - page 4
Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power sour ce until specified in Initial Set-Up. 120V model brewers require 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. "A" model brewers require 2-wire, grounded service rated 230 volts ac, 10 amp, single phase, 50 Hz. "B& ...
-
Bunn TU3Q - page 5
Page 5 10288 031604 1. Remove the shipping cap from the bulkhead fitting on the rear of the brewer . 2. Attach the flare fitting from the short piece of tubing on the strainer/flow control (supplied) to the water inlet fitting at the rear of the brewer . 3. Flush the water line and securely attach it to the flare fitting on the strainer/flow contro ...
-
Bunn TU3Q - page 6
Page 6 AUTO SWEETENER SET -UP (cont.) product for at least 4 minutes without shutting off. Some pump systems shut off after a few minutes of continu- ous running. 4. Plug brewer into the power sour ce. 5. Place an empty reservoir under the dilution nozzle of the brewer . 6. Close the adjustment valve on the rear of the brewer fully (clockwise), the ...
-
Bunn TU3Q - page 7
Page 7 10288 031604 OPERA TING CONTROLS A. ON/OFF Switch ON - Placing the switch in the left position allows the start switch to activate a timed brew cycle for three gallons of tea. OFF - Placing the switch in the right position stops the brew cycle. Stopping a brew cycle after it has been started will not stop the flow of water into the funnel un ...
-
Bunn TU3Q - page 8
Page 8 TEA BREWING 1. Begin each brew cycle with a clean empty brew funnel and server . (Be sure the server lid doesn’t interfere with the flow of dilution water .) 2. Insert a BUNN® filter into the funnel. 3. Pour the packet of loose fresh tea leaves into the filter . Approximately three to five ounces is recommended for three gallons of bevera ...
-
Bunn TU3Q - page 9
Page 9 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Ser vice Department. • Inspection, testing, and repair of electrical equipment should be performed only ...
-
Bunn TU3Q - page 10
Page 10 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY Brew cycle will not start (cont.) W ater is not hot Dilution cycle will not start Inconsistent beverage level in dispenser 6. Brew Timer 7. Brew Solenoid Valve 1. Limit Thermostat CAUTION - Do not eliminate or by- pass limit thermostat or thermal cut-off. Use only BOM replacement part #2 ...
-
Bunn TU3Q - page 11
Page 11 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY Consistently high or low beverage level in the dispenser Spitting or excessive steaming Drip-out time too long Sweetener is not working 1. External Strainer/Flow Control (.750 GPM) 1. Lime Build-up CAUTION - T ank and tank compo- nents should be delimed regularly depending on local water ...
-
Bunn TU3Q - page 12
Page 12 TROUBLESHOOTING (cont.) PROBLEM Dripping from sprayhead W ater flows into tank continuously (ON/OFF Switch "ON") (UNSWEET/OFF/SWEET Switch in "UNSWEET" or "SWEET" position) W ater flows into tank continuously (ON/OFF Switch "OFF") (UNSWEET/OFF/SWEET Switch in "UNSWEET" or "SWEET" p ...
-
Bunn TU3Q - page 13
Page 13 TROUBLESHOOTING (cont.) PROBLEM W eak beverage (cont.) Dry tea leaves remain in the funnel Brewer is making unusual noises PROBABLE CAUSE 4. Funnel Loading 5. Water T emperature 6. Low Brew Water V olume 1. Funnel Loading 1. Solenoid(s) 2. Plumbing Lines 3. W ater Supply 4. T ank Heater REMEDY The BUNN® paper filter must be centered in the ...
-
Bunn TU3Q - page 14
Page 14 SERVICE This section provides procedures for testing and replacing various major components used in this brewer should service become necessar y . Refer to T roubleshooting for assistance in determining the cause of any problem. WARNING - Inspection, testing, and repair of electri- cal equipment should be per formed only by qualified servic ...
-
Bunn TU3Q - page 15
Page 15 SERVICE (cont.) BREW SOLENOID V AL VE FIG. 2 BREW SOLENOID V AL VE P2087.40 Location: Viewing the brewer from the top, the brew sole- noid valve is mounted on the right side of the brewer. Test Procedures: 1. Disconnect the brewer from the power sour ce. 2. Disconnect the white/violet and white/green wires from the solenoid valve. With the ...
-
Bunn TU3Q - page 16
Page 16 SERVICE (cont.) BREW TIMER (Early Models) FIG. 4 BREW TIMER P2088.50 Location: The brew timer is located in the hood. It consists of the dial plate and circuit board. T est Procedure: 1. Disconnect the brewer from the power source. 2. Remove the wires from terminals TL3, TL4, & TL5 of the timer and rotate the dial fully counter clock- w ...
-
Bunn TU3Q - page 17
Page 17 SERVICE (cont.) DIGIT AL BREW TIMER (Late Models) FIG. 6 DIGIT AL BREW TIMER P2200.50 Location: The timer is located inside the hood, on the left side. Test Procedure. NOTE: Do not remove or install wires while timer board is installed. Pressure applied to one side may cause damage to the board. 1. Disconnect the brewer from the power sourc ...
-
Bunn TU3Q - page 18
Page 18 SERVICE (cont.) TL1 - WHI to Power Cord (100V & 120V) or RED to Power Connector (230V) and WHI to On/Off Switch (100V & 120V) or RED to On/Off Switch (230V) TL2 - WHI/VIO to Brew Solenoid and WHI/VIO to On/Off Switch TL3 - WHI/ORN to Start Switch TL4 - WHI/GRN to Brew Solenoid TL5 - WHI/YEL to Start Switch FIG. 7 DIGIT AL TIMER WIRI ...
-
Bunn TU3Q - page 19
Page 19 SERVICE (cont.) CONTROL THERMOST A T FIG. 8 CONTROL THERMOST A T P2200.50 Location: The control thermostat is located inside hood on the right side. Test Procedures: 1. Disconnect the brewer from the power sour ce. 2. Locate the blue/black wire on the control thermo- stat. 3. With a voltmeter , check the voltage across the blue/ black wire ...
-
Bunn TU3Q - page 20
Page 20 SERVICE (cont.) LIMIT THERMOST A T FIG. 10 LIMIT THERMOST A T P2200.50 Location: The limit thermostat is located inside the hood on the tank lid. T est Procedure: 1. Disconnect the brewer from the power source and remove the black wire from the limit thermostat. 2. With a voltmeter , check the voltage across the black wire removed from the ...
-
Bunn TU3Q - page 21
Page 21 SERVICE (cont.) ON/OFF SWITCH FIG. 12 ON/OFF SWITCH P2092.40 Location: The ON/OFF switch is located in the front of the hood, above and to the left of the brew funnel. T est Procedure: 1. Disconnect the brewer from the power sour ce. 2. Remove the black and white/violet wires from the switch terminals. 3. With a voltmeter , check the voltag ...
-
Bunn TU3Q - page 22
Page 22 If continuity is present as described, reconnect the wires, the switch is operating properly . If continuity is not present as described, replace the switch. Removal and Replacement: 1. Remove the wires from the switch terminals. 2. Compress the clips inside the hood and gently push the switch through the opening. 3. Push the new switch int ...
-
Bunn TU3Q - page 23
Page 23 SERVICE (cont.) T ANK HEA TER FIG. 16 T ANK HEA TER Location: The tank heater is located inside the tank and se- cured to the tank lid. T est Procedures: 1. Disconnect the brewer from the power supply . 2. With a voltmeter , check the voltage across the black and white wires on 100 volt and 120 volt models or the black and red wires for 230 ...
-
Bunn TU3Q - page 24
Page 24 SERVICE (cont.) 10288 031604 Location: Viewing the brewer from the front, the sweetener solenoid is mounted on the left side of the solenoid mounting bracket which is secured to the bottom base housing. T est Procedure: 1. Disconnect the brewer from the power source. 2. With a voltmeter , check the voltage across the brown/white and white/v ...
-
Bunn TU3Q - page 25
Page 25 10288 031604 SERVICE (cont.) OFF/SELECTOR SWITCH (SWEETENER OPTION) FIG. 20 OFF/SELECTOR SWITCH P2845.40 Location: The OFF/SELECTOR switch is located in the front of the hood, above and to the left of the brew funnel. T est Procedure: 1. Disconnect the brewer from the power sour ce. 2. With a voltmeter , check the voltage across the black w ...
-
Bunn TU3Q - page 26
Page 26 10288 110503 SCHEMA TIC WIRING DIAGRAM TU3Q (OPTIONAL) READY INDICA TOR BLU/BLK BLK SW . & THERMOST A T LIMIT THERMOST A T L1 BLK BLU/BLK BLK GREEN TA N K HEA TER N WHI WHI WHI WHI SW2 "KEEP WARM HEA TER" SW1 BLK WHI/VIO WHI/VIO WHI WHI WHI/ORA WHI/GRN WHI/YEL SOL 1 2 3 4 5 BREW TIMER 10287.0000C 10/03 © 1993 BUNN-O-MA TIC CO ...
-
Bunn TU3Q - page 27
Page 27 10288 031604 LIMIT THERMOSTAT BLU/BLK TANK HEATER "KEEP WARM" HEATER START L1 N BLK WHI BLK BREW TIMER WHI WHI GREEN WHI/YEL WHI/ORA BLK WHI/GRN WHI/VIO WHI BRN/WHI WHI/VIO WHI WHI SCHEMATIC WIRING DIAGRAM TU3Q W/SWEETENER 120 VOLTS AC 2 WIRE SINGLE PHASE THERMOSTAT SOL 1 2 3 4 5 SOL WHI/GRN WHI/VIO BREW SWTNR UNSWEET/OFF/SWEET (O ...
Hai una domanda su Bunn TU3Q?
Utilizza il modulo sottostante
Se non hai risolto il problema con Bunn TU3Q con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Bunn TU3Q è probabile che voglia condividere il modo di risolverlo.