-
Cisco MGX 8260 - page 1
CHAPTER 5-1 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 5 Connecting the Cables This chapter describes ho w to connect the interface cables, po wer the system, and check the status LEDs on circuit cards to make sure you ha ve installed e v erything properly . Cisco MGX 8260 conf igurations will require some type of cable management plan ...
-
Cisco MGX 8260 - page 2
5-2 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting the BITS Cable Connecting the BITS Cable A wiring diagram for a BITS cable is provided in Appendix A, “Cable and Connector Reference. ” To connect the BITS cable, follow these steps: Step 1 If your system uses a Building Integrated T iming Sour ...
-
Cisco MGX 8260 - page 3
5-3 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting DS3 Coaxial Cables Step 2 Connect the other end of the cable to the Stratum timing standard in your facility . Step 3 If your system has a redundant SCC, repeat Step 1 and Step 2 for the adjacent SCC. Note Do not daisychain the BITS connection to t ...
-
Cisco MGX 8260 - page 4
5-4 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting DS3 Coaxial Cables Figur e 5-2 Connecting Nonr edundant DS3 Cables T o connect DS3 cables to redundant BSCs, follow these steps. Note Label each cable with identifying information suitable for tracking in the MGX 8260 conf iguration database. Step ...
-
Cisco MGX 8260 - page 5
5-5 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting T1 Cables via RJ-21 Connectors Figur e 5-3 Connecting Redundant DS3 Cables Connecting T1 Cables via RJ-21 Connectors DS1 trunks consist of two pairs of tip and ring wires—one pair for transmit signals and one pair for receiv e signals. Prefabrica ...
-
Cisco MGX 8260 - page 6
5-6 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting T1 Cables via RJ-21 Connectors Step 5 T ighten the scre ws at the top and bottom of the recei ve 50-pin connector . Step 6 Repeat Step 1 through Step 5 for other NSC back cards. Figur e 5-4 Connecting T1 Cables PWR B -48VDC B RTN B PWR A -48VDC A R ...
-
Cisco MGX 8260 - page 7
5-7 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting E1 Cables via RJ-48 Connectors Connecting E1 Cables via RJ-48 Connectors Each E1 trunk consists of two pairs of tip and ring wires—one pair for transmit and one pair for recei ve. A 4-wire cable terminated with RJ-48 connectors connects the trunk ...
-
Cisco MGX 8260 - page 8
5-8 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting E1 Cables via RJ-48 Connectors Figur e 5-5 Connecting E1 Cables PWR B PWR A -48VDC A RTN A BITS CONSOLE AUX ALARM MGMT 12 RX TX 6 RX TX 1 RX TX 2 RX TX 3 RX TX 4 RX TX 5 RX TX 6 RX TX 1 RX TX 2 RX TX 3 RX TX 4 RX TX 5 RX TX 6 RX TX 1 RX TX 2 RX TX ...
-
Cisco MGX 8260 - page 9
5-9 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting Fast Ethernet Cables Connecting Fast Ethernet Cables This procedure applies to systems that use Fast Ethernet interf aces on the SCC back card for V oIP applications. Refer to Appendix A, “Cable and Connector Reference, ” for a cable wiring dia ...
-
Cisco MGX 8260 - page 10
5-10 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting OC-3 Cables Connecting OC-3 Cables Note This procedure applies to MGX 8260 nodes conf igured with SCC OC-3 back cards for f iber interf ace to Cisco MGX 8850 A TM switches. If your MGX 8260 node uses SCCs with Fast Ethernet back cards, skip this s ...
-
Cisco MGX 8260 - page 11
5-11 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting OC-3 Cables Figur e 5-7 Connecting OC-3 Cables PWR B PWR A -48VDC A RTN A BITS CONSOLE AUX ALARM MGMT 12 BITS CONSOLE AUX ALARM MGMT 12 RX TX 6 RX TX 1 RX TX 2 RX TX 3 RX TX 4 RX TX 5 RX TX 6 RX TX 1 RX TX 2 RX TX 3 RX TX 4 RX TX 5 RX TX 6 RX TX 1 ...
-
Cisco MGX 8260 - page 12
5-12 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting a Console Cable Connecting a Console Cable T o connect management console cables: Step 1 Connect an EIA/TIA-232 serial cable with a DB-9 connector to the SCC console connector . (See Figure 5-8 .) Use a cable with null modem wiring, rather than a ...
-
Cisco MGX 8260 - page 13
5-13 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting Management Cables Connecting Management Cables An SCC back card includes two Ethernet ports for remote management. Each port is assigned its o wn IP address. T o connect a 10BASE-T cable for MGX 8260 node management o ver a LAN: Step 1 Connect an ...
-
Cisco MGX 8260 - page 14
5-14 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Connecting Visual and Audible Alarms Connecting Visual and Audible Alarms T o connect alarm relay contacts, follow these steps: Step 1 Prepare a custom, multiple-conductor alarm cable for visual or audio alarms in your facility . T erminate this cable in a D ...
-
Cisco MGX 8260 - page 15
5-15 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Applying DC Power Step 5 Connect two return cables, one to each MGX 8260 R TN terminal for power circuit A. Connect the other ends to the R TN terminals at power source A. Step 6 Connect two supply cables, one to each –48V terminal for po wer circuit A. Co ...
-
Cisco MGX 8260 - page 16
5-16 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Applying DC Power Figur e 5-1 1 MGX 8260 Rear View of P ower Connections 31644 PWR B -48VDC B RTN B PWR A -48VDC A RTN A PWR A -48VDC A R TN A Silkscreened on chassis T o protective g round P o wer input terminals F eed A P o wer input terminals F eed B ...
-
Cisco MGX 8260 - page 17
5-17 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Applying DC Power Figur e 5-12 Installing the P o wer T er minal Cover PWR A -48VDC A R TN A PWR B -48VDC B R TN B 33385 ...
-
Cisco MGX 8260 - page 18
5-18 Cisco MGX 8260 Hardware Installation Guide 78-10966-02 Chapter 5 Connecting the Cables Verifying LED States Verifying LED States Immediately after po wer up, perform the following steps: Step 1 V erify that the PWR A indicator on each SCC is illuminated. (See Figure 5-13 .) Figur e 5-13 P o wer LEDs Step 2 If the chassis has been wired for pow ...
Hai una domanda su Cisco MGX 8260?
Utilizza il modulo sottostante
Se non hai risolto il problema con Cisco MGX 8260 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco MGX 8260 è probabile che voglia condividere il modo di risolverlo.