Italiano dropdown-ico

Manuale per l’uso Wybron pmn

25 pagine 0.25 mb
Scarica

Vai alla pagina of 25

Summary
  • Wybron pmn - page 1

    Power Supply User Manual ...

  • Wybron pmn - page 2

    2 19000 - 24 Way Coloram Power Supply (600 watts) 19012 - 12 Way Coloram Power Supply (300 watts) 19060 - 6 Way Coloram Power Supply (150 watts) Software versions: PS24 V3.0, PS12 V3.0, PS6 V3.0 Manual revision: March 30, 2001 CONTENTS Safety Information....................................................... 3 Introduction ......................... ...

  • Wybron pmn - page 3

    3 SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS This manual gives step-by-step instructions for preparation, setup and operation of The Coloram II Power Supply. There is a potential risk of fire, electric shock or injury to persons if the product is not used as instructed. This product is to be used in an in ...

  • Wybron pmn - page 4

    4 The Coloram II System The Coloram II System consists of one or more Color Changers or other components and a remote Power Supply. The DMX512 control signal from the lighting board is connected to the Power Supply and can continue on to more Coloram II Power Supplies or other DMX- controlled devices. The Power Supply sends both power and control s ...

  • Wybron pmn - page 5

    DMX CONSOLE DMX512 DMX Control console AC Power Goboram Gobo Changer Coloram II Color Changer To additional Color Changers or Gobo Changers Coloram II Power Supply To additional Coloram Power Supplies Buffered DMX512 To additional Color Changers or Gobo Changers To additional Color Changers or Gobo Changers Figure 1 Coloram II Color Changer 5 The C ...

  • Wybron pmn - page 6

    6 Power Supply The Power Supply converts the DMX512 signal level from the lighting console into Coloram I / Coloram II control signal which it then sends to each Color Changer along with 24 volts DC. The Power Supply features a DMX bypass relay to pass the DMX signal to the DMX output connector in the event of AC power loss. The Power Supply featur ...

  • Wybron pmn - page 7

    7 The Coloram II Power Supply menu This section describes the Power Supply menu. The following diagram is the eight character display and the three push buttons: /ENTER + _ DISPLAY The following diagram is an overall view of the Power Supply menu structure: XX UNITS SETUP OPTIONS SHUTDOWN SEND ? SEND ? POS ? XXX COMMANDS YES NO YES NO + - NORM LOW ...

  • Wybron pmn - page 8

    8 Menu Details The following is an explanation of functions and optional settings which are accessed via the various menus displayed. 1. POWER UP SCREENS When you connect the power supply to AC power, the following screens will appear on the display. 1. The INTRODUCTION screen will scroll through the software version and other information. 2. The R ...

  • Wybron pmn - page 9

    9 "Shut xxx" - Color changer reports a SHUTDOWN condition (will not respond to position commands because the voltage dropped below 15 VDC). "Drop xxx" - Color changer is disconnected and there is a loss of communication - it previously reported a status but is no longer doing so. "Motr xxx" - The color changer’s moto ...

  • Wybron pmn - page 10

    10 4. XX UNITS This is commonly referred to as the status menu. It displays the number of Color Changers, CXI’s and/or other Coloram components connected the power supply. Press [ - ] DMX 001 - Pressing [ /Enter ] allows you to select the DMX channel of the Color Changer or Gobo Changer which you wish to view the status of. Only channels with Col ...

  • Wybron pmn - page 11

    11 For The CXI color changer: CXI - Indicates there is a CXI color changer addressed to this channel. [ /Enter ] DCV 24.0 - This displays the DC voltage at the CXI. [ /Enter ] GLA 0% - This displays the % position of gel string A (farthest from the mounting plate). [ /Enter ] GLB 0% - This displays the % position of gel string B (nearest the mounti ...

  • Wybron pmn - page 12

    12 the gobo is spinning counter clock wise if the second control channel has a level of 00 - 49%. The display will tell you the gobo is spinning clock wise if the second control channel has a level of 51% - FL. When the third control channel has a level of FL and the second control channel has a level of 50%, the display will tell you the gobo is n ...

  • Wybron pmn - page 13

    13 DMXF OFF - DMX fan control channel. This enables or disables the lighting console fan speed control. This can be OFF (do not control the fans via a DMX channel), ONE (select one DMX channel to control all the color changer fans connected to that power supply) or BLK (select a BLOCK of DMX channels - one DMX channel for each channel of the power ...

  • Wybron pmn - page 14

    001 + - 048 14 If NO DMX signal is present, you will see the display (the first - changes to a + ) as follows: If an alert has been triggered with the presence of DMX signal, you will see the display (the second - changes to a + ) as follows: 001 - + 048 If an alert has been triggered without the presence of DMX signal, the display will look as fol ...

  • Wybron pmn - page 15

    15 Pos - This allows you to move the gelstring or gobo carrier independently from the lighting console. [ /Enter ] Fan - This allows you to change the fan speed independently from the lighting console. [ /Enter ] Mtr - This allows you to limit the top speed at which the motor will run. This applies to Coloram II. Installing / Connecting The Coloram ...

  • Wybron pmn - page 16

    16 3. Connect the Power Supply to AC power Plug the AC cord into a non-dimmed power circuit. The power supply automatically accommodates 100 - 132 VAC (50/60 Hz) or 170 - 240 VAC (50/60 Hz). Power at the Coloram II Power Supply is indicated by the red display which can be viewed from the stage. Power is also indicated on the bottom of each Color Ch ...

  • Wybron pmn - page 17

    17 The block of channels varies with the power supply model. For the 24 way power supply, the block is 48 channels. For the 12 way it is 24 channels and for the 6 way it is 12 channels. Set the Power Supply starting DMX channel by using the SETUP menu. If talkback is enabled on the power supply, the starting power supply channels are limited to 1, ...

  • Wybron pmn - page 18

    Figure 8 Coloram Power Supply Coloram cable 1 2 3 4 Coloram II Color Changer 100’ 20’ 20’ 20’ 18 To help understand this issue, think of it as water pressure (voltage) in a hose (cable) where you have multiple water sprinkler heads (color changers). If the hose (cable) is too long or you have too many sprinkler heads (color changers), the w ...

  • Wybron pmn - page 19

    Figure 6 90 - 250 VAC 50 / 60 HZ 4 AMP SLO - BLO AT 115 VAC 2 AMP SLO - BLO AT 230 VAC 12 WAY POWER SUPPLY 19012 Figure 10 19 Power Supply hanger brackets The Coloram II Power Supplies are shipped with hanger brackets to allow pipe or truss mounting. Follow these steps to install the hanger bracket. 1. Disconnect AC power from the Power Supply. 2. ...

  • Wybron pmn - page 20

    Figure 11 20 Power Supply rack mounting The Coloram II Power Supply rack mount accessory can be used with up to two Coloram II Power Supplies and allows them to be mounted into a 19 inch rack. Follow these steps to install the Power Supply into the rack mounting tray. 1. Disconnect AC power from the Power Supply. 2. Place the rack mount tray right ...

  • Wybron pmn - page 21

    21 Equipment Compatibility The following is a chart of compatibility and capacity of the various models of Coloram power supply and the companion components. Max # of Power Supply Model Output Channels Max # of Max # of Max # of Max # of Description Number Power Available CXI (2) Coloram (3) Eclipse (4) Goboram (5) 6 way 19060 150 watts 12 3 6 6 4 ...

  • Wybron pmn - page 22

    22 DMX512 control cable The DMX control cable from the lighting board to the Power Supply is a five conductor cable with 5-pin XLR connectors on each end. The wiring pin out is specified by the USITT DMX512 / 1990 standard. XLR Pin # Function 1 Common 2 Data - 3 Data + 4 Talkback - 5 Talkback + Specifications The Coloram II Power Supply Connectors: ...

  • Wybron pmn - page 23

    23 Software Version Changes The changes for power supply software version 3.0 from previous software versions are summarized below. 1. Added menus tree items to display data specific to CXI color changer. 2. The fan control DMX channel can be selected to be one channel or be a block of channels for individual color changer fan speed control (this b ...

  • Wybron pmn - page 24

    24 The Coloram II System cable 7042-3 ............... 3’ power/signal cable 7042-5 ............... 5’ power/signal cable 7042-10 ............. 10’ power/signal cable 7042-15 ............. 15’ power/signal cable 7042-25 ............. 25’ power/signal cable 7042-50 ............. 50’ power/signal cable 7042-75 ............. 75’ power/sig ...

  • Wybron pmn - page 25

    particular purpose and of other obligations and liabilities on our part. The owner acknowledges that no other representations were made to him or relied upon him with respect to the quality and function of the goods sold. This written warranty is intended as a complete and exclusive statement of the terms thereof. Prior dealings or trade usage shal ...

Fabbricante Wybron Categoria Power Supply

I documenti che otteniamo dal fabbricante del dispositivoWybron pmn possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Wybron
- manuali per l’uso pmn
- schede prodotto Wybron
- opuscoli
- o etichette energetiche Wybron pmn
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Wybron pmn.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Wybron pmn, manuali di manutenzione, brevi manuali o manuali utente Wybron pmn. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Wybron pmn.

Manuali per l’uso simili

Manuale completo del dispositivo Wybron pmn, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Wybron pmn dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Wybron pmn.

Il manuale per l’uso completo Wybron, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Wybron pmn - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Wybron pmn, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Wybron pmn che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Wybron pmn - che ci dovrebbe aiutare nei primi passi durante l'uso Wybron pmn
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Wybron pmn
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Wybron pmn in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Wybron pmn?

Utilizza il modulo sottostante

Se non hai risolto il problema con Wybron pmn con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Wybron pmn è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)