-
Chicago Electric 94866 - page 1
ELECTRIC BLO WER/V A CUUM Model 94866 ASSEMBL Y AND OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.com Cop yright © 2006 by Harbor F reight T ools ® . All rights reser v ed. No por tion of this manual or an y ar twork contained herein ma y be reproduced in any shape or f or ...
-
Chicago Electric 94866 - page 2
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety warnings and precautions, assembl y , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep y our in v oice with this manual. Write the in v oice number on the inside of the front co ver . Keep this manual and in v o ...
-
Chicago Electric 94866 - page 3
ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding pr ong or modify the plug in any wa y . Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the ...
-
Chicago Electric 94866 - page 4
12. A v oid accidental starting. Be sure the P ower Switch is off bef ore plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Remove adjusting ke ys or wrenches bef ore turning the power tool on. A wrench or a key that is left attached to a rotating part ...
-
Chicago Electric 94866 - page 5
23. T ool service must be perf ormed only b y qualified repair personnel. Ser vice or maintenance perf or med b y unqualified personnel could result in a r isk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthoriz ...
-
Chicago Electric 94866 - page 6
9. Alwa ys turn off the Blower/V acuum and unplug the unit from its electrical outlet be f ore perf orming any maintenance or changing accessories. 10. Do not use the Blow er/V acuum with an y openings bloc ked. K eep free of dir t, dust, leav es, and an ything that ma y reduce air flow or hinder motor operation. 11. Do not use the Blower/V acuum t ...
-
Chicago Electric 94866 - page 7
GROUNDING W ARNING! GROUNDED T OOLS: T OOLS WITH THREE PRONG PLUGS 1 . T ools mar k ed with “Grounding Required” ha v e a three wire cord and three prong grounding plug. The plug must be connected to a proper ly g rounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carr y electr ...
-
Chicago Electric 94866 - page 8
EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of p ...
-
Chicago Electric 94866 - page 9
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable f or outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using i ...
-
Chicago Electric 94866 - page 10
UNP A CKING When unpacking, chec k to make sure all the par ts sho wn on the P ar ts List on page 14 are included. If any par ts are missing or broken, please call Harbor F reight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y INSTR UCTIONS 1. CA UTION! Alwa ys make sure the P ower Switch (4) of the Blo wer/V ...
-
Chicago Electric 94866 - page 11
SKU 94866 For technical questions, please call 1-800-444-3353 P A G E 1 1 T o Assemb le The V acuum Unit: 1. Remov e the Protection Cov er (7) b y tur ning it countercloc kwise. (See Figure F .) 2. Inser t the V acuum Pipe Center Piece (8) onto the Housing (14). Then, tur n the V acuum Pipe Center Piece clockwise to loc k it in position. (See Figur ...
-
Chicago Electric 94866 - page 12
SKU 94866 For technical questions, please call 1-800-444-3353 P A G E 1 2 mov e the unit slowly and e v enly . (See Figure G.) T o Operate The V acuum: 1. Make sure to remo v e the Protection Co v er (7). Also, mak e sure the V acuum Bag (11) is properly connected to the unit and its Shoulder Strap is properly adjusted. (See Figure F . 2. Plug the ...
-
Chicago Electric 94866 - page 13
INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Make sure the P ower Switch (4) of the Blo wer/V acuum is in its “OFF” position and the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 2. Before eac h use: Inspect the gener al condition of the Blo wer/V acuum. Check f or misa ...
-
Chicago Electric 94866 - page 14
P ARTS LIST AND ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and sho wn for illustr ation purposes only , and are not av ailable individually as replacement parts. SKU 94866 For technical questions, please call 1-800-444-3353 P A G E 1 4 7 2 3 4 5 13 1 12 6 10 11 8 9 13 14 14 P a rt # D e scription Q ty. P a rt # D e scription Q ty. 1 Upper Han ...
-
Chicago Electric 94866 - page 15
W ARRANTY SKU 94866 For technical questions, please call 1-800-444-3353 P AGE 1 5 Harbor Freight T ools Co . makes e ve r y effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from def ects in materials and w or kmanship f or the pe r iod of ninety da ys fro ...
Chicago Electric 94866についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもChicago Electric 94866の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがChicago Electric 94866で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。