日本語 dropdown-ico

Chamberlain SECURITY+ 3265M 1/2 HPの取扱説明書

36ページ 3.42 mb
ダウンロード

ページに移動 of 36

Summary
  • Chamberlain SECURITY+ 3265M 1/2 HP - page 1

    The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com GARAGE DOOR OPENER Models 3265M 1/2 HP 3265M-267 1/2 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 2

    2 Introduction 2-5 Safety symbol and signal word review . . . . . . . . . . . . . . . 2 Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . 3 Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Carton inventory ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 3

    3 To prevent damage to garage door and opener: • ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage. Preparing your garage door Before you begin: • Disable locks. • Remove any ropes connected to garage door. • Complete the following test to make ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 4

    4 ONE-PIECE DOOR WITHOUT TRACK ONE-PIECE DOOR WITH TRACK Planning Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may fi nd it helpful to refer back to this page and the accompanying illustrations as you proceed wit ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 5

    5 Your garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below. Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below. Carton Inventory Straight Door Arm Section Cu ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 6

    6 ASSEMBLY STEP 1 Attach the Rail to the Motor Unit To avoid installation diffi culties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Position rail at a 45˚ angle to opener so one hole in rail and motor unit line up. • Thread one of the washered bolts part way i ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 7

    7 INSTALLATION ASSEMBLY STEP 3 Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley. • To tighten the chain, turn outer nut in the direction shown (Figure 1). • When the chain is approximately 1/2" (13 mm) above the base of the rail at its midpoint, re-tighten the inner nut to secu ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 8

    8 INSTALLATION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door. 1. Close the door and mark the inside vertical centerline of the garage door. 2. Extend the line onto the header wall above the door. You can fasten the header bracket within 4 fe ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 9

    9 Garage Door - Finished Ceiling - The nail hole is for positioning only. You must use lag screws to mount the header bracket. Vertical Centerline of Garage Door Header Wall Vertical Centerline of Garage Door Lag Screws 5/16"-9x1-5/8" Header Bracket Door Spring 6" (15 cm) Maximum INSTALLATION STEP 2 Install the Header Bracket You can ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 10

    10 INSTALLATION STEP 4 Position the Opener Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid fl at is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 11

    11 INSTALLATION STEP 5 Hang the Opener Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On fi nished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 12

    12 KG 1 3 9 7 5 KG 1 3 9 7 5 To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is NOT connected BEFORE installing door control. • Connect ONLY to 24 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage door: • Install door control within sight of garage door, out of reach of c ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 13

    13 INSTALLATION STEP 7 Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. Light bulb size should be A19, standard neck only. The light will turn ON and rema ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 14

    14 INSTALLATION STEP 9 Electrical Requirements To avoid installation diffi culties, do not run the opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fi t into a grounding type outlet. If the plug doesn’t fi t into the outlet you have, con ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 15

    15 Facing the door from inside the garage INSTALLATION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR When properly connected and aligned, the sensor will detect an obsta ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 16

    16 INSTALLING THE BRACKETS Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the fl oor. They may be installed in one of three ways, as follows. Garage door track installation (preferred) (Figure 1): • Slip the ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 17

    17 MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5). • Finger tighten the wing nuts. ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 18

    18 ALIGNING THE SAFETY REVERSING SENSORS • Plug in the opener. The indicator lights in both the sending and receiving eyes will glow steadily if wiring connections and alignment are correct. The sending eye amber indicator light will glow regardless of alignment or obstruction. If the green indicator light in the receiving eye is off, dim, or fl ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 19

    19 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. INSTALLATION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 20

    20 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes. • Metal Doors: Drill 3/16" pilot holes ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 21

    21 INSTALLATION STEP 12 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 22

    22 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 5: IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm (Figure 5). • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to th ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 23

    23 ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. To operate the opener, press the Door Control push bar. Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not reverse ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 24

    24 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door. If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weathe ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 25

    25 ADJUSTMENT STEP 3 Test the Safety Reversal System TEST • With the door fully open, place a 1-1/2" (3.8 cm) board (or a 2x4 laid fl at) on the fl oor, centered under the garage door. • Operate the door in the down direction. The door must reverse on striking the obstruction. ADJUST • If the door stops on the obstruction, it is not tr ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 26

    26 OPERATION Using Your Garage Door Opener Your Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Your opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. If you purcha ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 27

    27 MANUAL DISCONNECT POSITION Using the Wall-Mounted Door Control THE MULTI-FUNCTION DOOR CONTROL Press the push button to open or close the door. Press again to reverse the door during the closing cycle or to stop the door while it's opening. Light feature Press the Light button to turn the opener light on or off. It will not control the open ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 28

    28 Care of Your Opener LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the fi rst year of operation. Pages 23 and 24 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully. Repeat the safety reverse ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 29

    29 Having a Problem? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • Verify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Insta ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 30

    30 Your garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will fl ash a number of times then pause signifying it has found a potential issue. Consult Diagnostic Chart below. Diagnostic Chart Symptom: One or both of the indicator lights on the safety reversing sensors do not glow steady. • I ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 31

    31 *3-Button Remotes If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. To Erase All Codes From Motor Unit Memory To deactivate any unwanted remote, fi rst ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 32

    32 LOCK L I GHT 1. Enter a four digit personal identifi cation number (PIN) of your choice on the keypad. Then press and hold enter. 2. While holding the ENTER button, press and hold the LIGHT button on the door control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the door control (all three buttons are held). 4 ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 33

    33 7 10 11 5 NOTICE U P CE ILIN G M OUNT O NL Y 8 6 1 4 3 2 LOCK LIGHT 9 12 2 3 5 6 7 12 11 9 8 1 4 10 1 3 4 5 2 1 2 3 4 5 6 6 REPAIR PARTS Rail Assembly Parts KEY PART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A4813 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 1707LM One-piece rail - 7' (2.1 m) 1708LM One-piece rail - 8&a ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 34

    34 Motor Unit Assembly Parts KEY PART NO. NO. DESCRIPTION 1 31D380 Sprocket cover 2 41C4220A Gear and sprocket assembly Complete with: Spring washer, thrust washer, retaining ring, bearing plate, roll pins (2), drive gear and worm gear, helical gear w/retainer and grease 3 41B4245 Line cord 4 41A5484-1 End panel w/all labels 5 4A1344 Light socket 6 ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 35

    35 CLOSED OPEN ACCESSORIES 374LM 370LM 395LM 41A5281 1702LM Remote Light Control: Enables homeowner to turn on a lamp, television or other appliance from their car with their garage door opener remote or from anywhere in their home with an additional LiftMaster Security ✚ ® remote. 4-Button Security ✚ ® Remote Control: Includes visor clip. 37 ...

  • Chamberlain SECURITY+ 3265M 1/2 HP - page 36

    36 © 2011, The Chamberlain Group, Inc. 114A4255B All Rights Reserved LIFTMASTER ONE-YEAR LIMITED WARRANTY LIFETIME MOTOR LIMITED WARRANTY The Chamberlain Group, Inc. (“Seller”) warrants to the fi rst retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defect in materials and/ ...

メーカー Chamberlain カテゴリー Garage Door Opener

Chamberlain SECURITY+ 3265M 1/2 HPのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SECURITY+ 3265M 1/2 HPの取扱説明書
- Chamberlainの製品カード
- パンフレット
- またはChamberlain SECURITY+ 3265M 1/2 HPの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Chamberlain SECURITY+ 3265M 1/2 HPの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Chamberlain SECURITY+ 3265M 1/2 HPの取り付け説明書、サービスマニュアル、簡易説明書、またはChamberlain SECURITY+ 3265M 1/2 HPのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Chamberlain SECURITY+ 3265M 1/2 HPの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Chamberlain SECURITY+ 3265M 1/2 HPデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがChamberlain SECURITY+ 3265M 1/2 HPを使用するのを助ける技術的文書のことです。説明書は通常、全てのChamberlain SECURITY+ 3265M 1/2 HPユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Chamberlainの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Chamberlain SECURITY+ 3265M 1/2 HPの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははChamberlain SECURITY+ 3265M 1/2 HPの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Chamberlain SECURITY+ 3265M 1/2 HPに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Chamberlain SECURITY+ 3265M 1/2 HPデバイスの基本機能を使うにあたってのヒント。 Chamberlain SECURITY+ 3265M 1/2 HPのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Chamberlain SECURITY+ 3265M 1/2 HPに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるChamberlain SECURITY+ 3265M 1/2 HPのメーカー/サービスへの連絡先に関する情報。

Chamberlain SECURITY+ 3265M 1/2 HPについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもChamberlain SECURITY+ 3265M 1/2 HPの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがChamberlain SECURITY+ 3265M 1/2 HPで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)