日本語 dropdown-ico

Yard Machines 41AD-280G000の取扱説明書

22ページ 0.84 mb
ダウンロード

ページに移動 of 22

Summary
  • Yard Machines 41AD-280G000 - page 1

    Operator’ s Manual Curved Shaft, 2-Cycle T rimmer Model 41AD-280G000 IMPORT ANT : Read safety rules and instructions carefully befor e operating equipment. W arning: This unit is equipped with an inter nal combustion engine and should not be used on or near any unimproved for est- covered, brush-cover ed or grass-covered land unless the engine’ ...

  • Yard Machines 41AD-280G000 - page 2

    2 T ABLE OF CONTENTS Content Page Important Safe Operation Practices .................................................................... 3-5 Assembling Y our T rimmer .................................................................................... 6 Know Y our T rimmer ........................................................................... ...

  • Yard Machines 41AD-280G000 - page 3

    3 SECTION 1: IMPOR T ANT SAFE OPERA TION PRACTICES This Symbol Points Out Important Safety Information Which, If Not Followed, Could Endanger The Personal Safety And/or Property Of Y ourself And Others. Read And Follow All Instructions In This Manual Before Attempting T o Operate Y our T rimmer . Failure T o Comply With These Instructions May Resul ...

  • Yard Machines 41AD-280G000 - page 4

    4 • This unit does not have a clutch. The cutting attachment continues to rotate when the engine is idling. T o prevent injury , have the unit adjusted by an authorized service technician. • Adjust the D-Handle to your size to provide the best grip. • Be sure the cutting attachment is not in contact with anything before starting the unit. • ...

  • Yard Machines 41AD-280G000 - page 5

    5 • PRIMER BULB Push primer bulb, fully and slowly , 5 to 7 times. • UNLEADED FUEL Always use clean, fresh unleaded fuel. • OIL Refer to operator's manual for the proper type of oil. • THROWN OBJECTS CAN CAUSE SEVERE INJUR Y Do not operate unit without proper attachments and guar ds in place. • ON/OFF STOP CONTROL ON / ST ART / RUN ? ...

  • Yard Machines 41AD-280G000 - page 6

    6 Figure 4 Installing and Adjusting the D-Handle NOTE: The bolt, washer and wing nut need to be removed from the D-handle before installing. 1. Push the D-handle down onto the shaft housing so that the handle slants towards the shaft grip. The squared bolt hole in the handle is to the right. See Figure 1. 2. Insert the shoulder bolt into the square ...

  • Yard Machines 41AD-280G000 - page 7

    7 Figure 5 SECTION 3: KNOW Y OUR TRIMMER Primer Bulb Choke Control Air Filter/ Muffler Cover Spark Plug Muffler On/Off Stop Control STOP/OFF (O) ST ART/ON (I) Throttle Control Read this operator’ s manual and safety rules befor e operating your trimmer . Compare illustrations in Figure 5 with your trimmer to familiarize yourself with the location ...

  • Yard Machines 41AD-280G000 - page 8

    8 SECTION 4: OPERA TING Y OUR TRIMMER Oil and Gas Mixing Instructions Old and/or improperly mixed fuel ar e the main reasons for the unit not running pr operly . Be sur e to use fresh, clean unleaded fuel. Follow the instructions carefully for the pr oper fuel/oil mixture. Definition of Blended Fuels T oday's fuels are often a blend of gasolin ...

  • Yard Machines 41AD-280G000 - page 9

    9 Choke Control Full Choke Position (A) Primer Bulb Starting Engine WARNING: A void accidental starting. Be in the starting position when pulling the starter rope. See Figur e 9. The operator and unit must be in a stable position while starting to avoid serious personal injury . WARNING: Operate this unit only in a well ventilated area outdoors. Ca ...

  • Yard Machines 41AD-280G000 - page 10

    Each time the head is bumped, about 1 inch (25.4 mm) of trimming line is released. A blade in the cut- ting attachment shield will cut the line to the proper length if excess line is released. For best results, tap the Bump Head™ on bar e ground or har d soil. If line release is attempted in tall grass, the engine may stall. Always keep the trimm ...

  • Yard Machines 41AD-280G000 - page 11

    11 Figure 12 Decorativ e T rimming Decorative trimming is accomplished by removing all vegetation around tr ees, posts, fences, etc. Rotate the whole unit so that the cutting attachment is at a 30° angle to the ground. See Figur e 12. Tips for Best T rimming Results • Keep the cutting attachment parallel to the ground. • Do not force the cutti ...

  • Yard Machines 41AD-280G000 - page 12

    12 SECTION 5: MAKING ADJUSTMENTS Idle Speed Screw Figure 13 Engine Specifications Engine T ype … … … … … … …Air -Cooled, 2-Cycle Displacement … … … … … … … … … … … 31cc Idle Speed R.P .M. … … … … … 3,400- 4,400 rpm Operating R.P .M. … … … … … … 6,600-8,000 rpm Fuel/Oil Mixture Ratio. … … ...

  • Yard Machines 41AD-280G000 - page 13

    13 WARNING: T o avoid serious personal injury , always tur n the unit off, allow it to cool and disconnect the spark plug before you clean or perform any maintenance on it. T rouble Shooting Refer to the trouble shooting chart for mor e informa- tion. Engine IMPORT ANT : Never run your engine without air cleaner completely assembled. Air Filter Mai ...

  • Yard Machines 41AD-280G000 - page 14

    14 8. Place the air filter/muffler cover over the back of the carburetor and muf fler . NOTE: The choke control must be in the P ARTIAL choke position (B) to install the air filter/muffler cover . See Figure 14. 9. Insert the four (4) screws into the holes in the air filter/muffler cover and tighten. See Figur e 14. Use a flat blade or # T20 T orx ...

  • Yard Machines 41AD-280G000 - page 15

    15 Figure 19 Figure 22 Figure 23 Figure 24 Figure 20 Figure 21 Single Line Installation Go T o Step 8 for SplitLine™ Installation 6. T ake approximately 25 feet (7.6 m) of new trim- ming line, loop it into two equal lengths. Insert each end of the line through one of the two holes in the inner reel. Pull the line thr ough the inner reel so that t ...

  • Yard Machines 41AD-280G000 - page 16

    16 SECTION 7: OFF SEASON STORAGE If the unit will be stored for an extended time, 1. Drain all fuel from the fuel tank into a container . Do not use fuel that has been stored for mor e than 60 days. Dispose of the old fuel in accordance to local r egulations. 2. Start the engine and allow it to run until it stalls. This ensures that all fuel has be ...

  • Yard Machines 41AD-280G000 - page 17

    17 SECTION 8: TROUBLE SHOOTING GUIDE ENGINE WILL NOT ST ART ENGINE WILL NOT IDLE ENGINE WILL NOT ACCELERA TE ENGINE LACKS POWER OR ST ALLS WHEN UNDER LOAD CUTTING A TT ACHMENT WILL NOT ADV ANCE LINE On/Off Stop Contr ol in the STOP position Empty fuel tank Primer bulb wasn't pressed enough Engine flooded Old or improperly mixed fuel Fouled spa ...

  • Yard Machines 41AD-280G000 - page 18

    18 SECTION 9: P AR TS LIST FOR MODEL 41AD-280G000 42 1 2 3 8 10 12 3 4 5 7 6 11 13 15 16 47 48 43 14 22 49 20 17 18 19 21 26 27 28 31 32 30 33 34 36 37 38 35 25 32 39 40 46 41 44 42 45 24 29 23 9 ...

  • Yard Machines 41AD-280G000 - page 19

    19 1 182059 Air Cleaner/Muffler Cover Assembly (includes 2 & 42) 2 180350 Air Cleaner Filter 3 181345 Carburetor Mounting Scr ew Assembly 4 180226 W avey W asher 5 182160 Choke Lever Assembly (includes 6) 6 182161 Choke Knob and Screw 7 182162 Choke Lever and Plate (includes 5) 8 182062 Carburetor Assembly W/Limiter Caps (includes 9 & 21) 9 ...

  • Yard Machines 41AD-280G000 - page 20

    20 MODEL 41AD-280G000 10 8 13 9 17 16 18 19 15 11 12 14 1 1 5 6 7 4 3 2 ...

  • Yard Machines 41AD-280G000 - page 21

    21 1 182093 Throttle Housing and T rigger Assembly (includes 2 & 3) 2 610314 Throttle T rigger Spring 3 180975 Throttle T rigger 4 182068 Throttle Cable Assembly 5 145819 D-Handle Assembly 6 181587 D-Handle Hardwar e 7 181893 Drive Shaft Housing Assembly 8 153597 Lower Clamp Assembly 9 682064 Flexible Drive Shaft 10 180531 Shield Mounting Screw ...

  • Yard Machines 41AD-280G000 - page 22

    MANUF ACTURER’S LIMITED W ARRANTY FOR: No implied warranty , including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty , whether written or oral, except as mentioned above, given b ...

メーカー Yard Machines カテゴリー Trimmer

Yard Machines 41AD-280G000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 41AD-280G000の取扱説明書
- Yard Machinesの製品カード
- パンフレット
- またはYard Machines 41AD-280G000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Yard Machines 41AD-280G000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Yard Machines 41AD-280G000の取り付け説明書、サービスマニュアル、簡易説明書、またはYard Machines 41AD-280G000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Yard Machines 41AD-280G000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Yard Machines 41AD-280G000デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがYard Machines 41AD-280G000を使用するのを助ける技術的文書のことです。説明書は通常、全てのYard Machines 41AD-280G000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Yard Machinesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Yard Machines 41AD-280G000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははYard Machines 41AD-280G000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Yard Machines 41AD-280G000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Yard Machines 41AD-280G000デバイスの基本機能を使うにあたってのヒント。 Yard Machines 41AD-280G000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Yard Machines 41AD-280G000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるYard Machines 41AD-280G000のメーカー/サービスへの連絡先に関する情報。

Yard Machines 41AD-280G000についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもYard Machines 41AD-280G000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがYard Machines 41AD-280G000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)