Actiontec electronic V.90の取扱説明書

33ページ 0.41 mb
ダウンロード

ページに移動 of 33

Summary
  • Actiontec electronic V.90 - page 1

    ...

  • Actiontec electronic V.90 - page 2

    2 T able of Contents Do This First ................................................................................................................. 3 For W indows 3.1X Installation .............................................................................. 3 For W indows 95/98 Installation ....................................................... ...

  • Actiontec electronic V.90 - page 3

    3 Do This First Please read the following tips carefully before attempting to install your new modem. For W INDOWS 3.1 I NST ALLA TION  Because W indows 3.1 and 3.1 1 are not Plug-N-Play operating systems, it is suggested that you do not rely on the Plug-N-Play capabilities of your com- puter to automatically configure the modem. Instead, manual ...

  • Actiontec electronic V.90 - page 4

    4 For W INDOWS 95/98 I NST ALLA TION  If you are replacing an existing modem in your computer system with this modem, be sure to remove all other modem drivers. Go to: Start-Settings- Control Panel and double-click on the System icon. Select the Device Man- ager tab. Double-click on the Modems icon in the device tree to show the modems installed ...

  • Actiontec electronic V.90 - page 5

    5  (Note: If you are using the default Play-N-Play jumper settings and not manu- ally configuring the COM Port and IRQ jumpers, the following step may be skipped. Refer back to this area only if Plug-N-Play cannot successfully con- figure your modem.) The modem will need one IRQ (interrupt) and one COM Port to function. T o check for any availab ...

  • Actiontec electronic V.90 - page 6

    6 Go to your system BIOS Setup routine and find the Plug-N-Play settings. These settings can be found within the Advanced , PNP/PCI Configuration , or Plug and Play Configuration sections depending on the BIOS Manufac- turer . Next, verify that one free IRQ has been set so that the ISA bus has access to it (some BIOS dont allow individual select ...

  • Actiontec electronic V.90 - page 7

    7 consult your computer  s user manual. Be sure to Save the settings befor e exiting the BIOS Setup. The computer will then reboot. Set your modem s jumpers to COM 2 - IRQ 3. (See Jumper Settings in the Installing the Mo- dem section for jumper setting diagrams.)  Y ou are now ready to install the modem. Proceed to the next section. Instal ...

  • Actiontec electronic V.90 - page 8

    8 Jumper Block JP2 is used to select the IRQ (interrupt request) settings for the modem. Figure 4: below details the possible selections. Figur e 4: JP2 IRQ (interrupt request) Options HARDW ARE INST ALLATION 1. T urn off the computer and all peripheral devices connected to it. 2. Unplug the computer power cord from the wall receptacle. 3. Remove t ...

  • Actiontec electronic V.90 - page 9

    9 5. Firmly , but gently , insert the modem into the available 16-bit expansion slot. Ensure that the card is seated properly before securing it with the screw re- moved in Step 4, as shown in the following diagram: Fig. 6: Installing The Modem 6. Put the chassis cover back on the computer . 7. Be sure that all power switches are in the OFF positio ...

  • Actiontec electronic V.90 - page 10

    10 CONNECTING DEVICES TO THE MODEM Fig.7: Connecting Devices On the rear panel of your modem are input jacks to connect devices to the modem. As shown in the diagram, there are jacks for connection to a phone and to a phone line . The connector labeled Line ( T elco ) is meant to be connected to a standard analog phone line. T o help reduce the loa ...

  • Actiontec electronic V.90 - page 11

    11 Step 5 Click OK to copy the W ave Device .INF file from the A: drive to the hard drive. Step 6 T o determine what COM port and IRQ is assigned to the modem in W in- dows 95, click on the Modems icon in Contr ol Panel and select the Diagnostic tab. Click on the COM Port icon and then on the Mor e Info button to view the modem properties. CONFIGU ...

  • Actiontec electronic V.90 - page 12

    12 diskette or CD-ROM into the appropriate drive. Click Next> . Step 3 W indows will show a screen asking  What do you want W indows to do? . Select:  sear ch for the best driver for your device.  Click Next> . Step 4 A search screen will display options to do your search. Put a check on Floppy disk drives and CD-ROM drive . ...

  • Actiontec electronic V.90 - page 13

    13 Step 1 Reboot the computer and log in to W indows NT 4.00. Step 2 Go to: Start-Settings-Control Panel and double-click on the Modems icon. At the Modems Pr operties dialog box, click Add . Step 3 An Install New Modem window should appear . Allow W indows NT to detect your modem. Click on the Next> button. Step 4 If a modem is found, W indows ...

  • Actiontec electronic V.90 - page 14

    14 Installing and Configuring Communications Software If your modem came with a communications software package, it is strongly rec- ommended that you use this software for your modem. It s default installation parameters have been specially configured to work with this modem. The Users Guide for this program can be found inside the modem packag ...

  • Actiontec electronic V.90 - page 15

    15 T r oubleshooting Most problems encountered during the W indows 95/98/NT installation process are a result of inadequate system resources. If you skipped some of the recom- mended preinstallation procedures outlined in the Do This First section, return to the beginning of that section and carefully follow all steps outlined for the operat- ing s ...

  • Actiontec electronic V.90 - page 16

    16 sour ces tab and read the Conflicting Device List . If a conflict is present, uncheck the box Use automatic settings and select a configuration that does not cause conflicts. Manually change the IRQ settings if needed (see your W indows 95 on-line help file for a more detailed discussion on changing these settings). Click on the OK button. ...

  • Actiontec electronic V.90 - page 17

    17 COM Ports, one LPT port, keyboard, and a mouse. Each of these de- vices require at least one IRQ (interrupt) in order to function. Some models of sound card require three interrupts. It is little wonder that when it comes time to install a modem, there is nothing left. The addition of special purpose peripherals (SCSI, Network cards, etc.) makes ...

  • Actiontec electronic V.90 - page 18

    18 Common Pr oblems : No Dialtone Error Make sure you have connected the phone cable into the right connector on the back of the modem. See Figure 7: Connecting Devices . Y ou may have too many devices connected to the phone line. Remove all other equipment. Y our modem may not recognize overseas dialtone. Use A TX0 to have the modem ignore (not lo ...

  • Actiontec electronic V.90 - page 19

    19 The number you are calling may not support V .90 protocols. Some ISP s ( I nternet S ervice P roviders) have special numbers that you must call to connect to V .90. Contact your service provider and ask if the number you are calling supports V .90 connections to their service. Check the maximum speed setting in the Modem Properties window . G ...

  • Actiontec electronic V.90 - page 20

    20 Appendix A: A T Command Set A T Commands A T commands are issued to the modem to control the modems operation and software configuration. A T commands can only be entered while the modem is in command mode. The format for entering A T commands is: TYPE: A TXn where X is the A T command, and n is the specific value for that command. PRESS: Ent ...

  • Actiontec electronic V.90 - page 21

    21 TYPE: A TSn?<enter> where n is the register number . T o modify the value of an S-register: TYPE: A TSn = r<enter> where n is the register number , and r is the new register value. Common A T Commands and S Registers The following are some common A T Commands. If you require a complete listing of the A T Command and S Register option ...

  • Actiontec electronic V.90 - page 22

    22 This command controls whether or not the characters entered from your computer keyboard are echoed back to your monitor while the modem is in command mode. E0: Disables echo to the computer . E1: Enables echo to the computer (default). Fn On-line Data Character Echo Command This command determines if the modem will echo data from the DTE. F0: On ...

  • Actiontec electronic V.90 - page 23

    23 Mn Monitor Speaker Mode This command turns the speaker on or off. M0: The speaker is off. M1: The speaker is on until the modem detects the carrier signal (default). M2: The speaker is always on when modem is off-hook. M3: The speaker is on until the carrier is detected, except while dialing. On Return On-line to Data Mode O0: Instructs the mode ...

  • Actiontec electronic V.90 - page 24

    24 V1: Displays result codes as text (default). Wn Result Code Option W0: CONNECT result code reports DTE (modem to computer) speed. W1: CONNECT result code reports DTE speed. W2: CONNECT result code reports DCE (modem to modem) speed. W3: CONNECT result code reports DTE speed and information on error cor- rection and data compression. W4: Reports ...

  • Actiontec electronic V.90 - page 25

    25 &F Load Factory Settings This command loads the configuration stored and programmed at the factory . This operation replaces all of the command options and the S-register settings in the active configuration with factory values. &F: Recall factory setting as active configuration. (default) &Gn V .22bis Guard T one Control This comman ...

  • Actiontec electronic V.90 - page 26

    26 &S1: DSR comes on when establishing a connection and when carrier is lost. &Vn V iew Active Configuration and Stor ed Profile This command is used to display the active profiles. &V0: V iew stored profile 0. &V1: V iew stored profile 1. &V3: V iew relay and general-purpose input-output status. &Wn Store Curr ent Configura ...

  • Actiontec electronic V.90 - page 27

    27 %G0: Disabled. %G1: Enabled. -Cn Data Calling T one Data Calling T one is a tone of certain frequency and cadence as specified in V .25 which allows remote Data/F AX/V oice discrimination. The frequency is 1300 Hz with a cadence of .5 s on and 2 s off. -CO: Disabled. -C1: Enabled. (default) -C2: Enable V .8 and 1300 Hz calling tone. +MS=m Modula ...

  • Actiontec electronic V.90 - page 28

    28 <min rate> This entry specifies the lowest data transfer rate which the modem may establish a connection. <max rate> This parameter specifies the highest speed at which the modem may establish a connection. S0 Number of Rings to Auto-answer The modem automatically goes off-hook and initiates a data mode-answer mode handshake after de ...

  • Actiontec electronic V.90 - page 29

    29 Range: 0-127 Default: 8 S6 W ait Befor e Blind Dialing The value of S6 specifies the amount of time that must elapse after the modem goes off-hook before the modem starts dialing the telephone number . The modem waits for at least 2 seconds before dialing even if the register is set for a value less than two. Range: 2-255 Default: 2 S7 W ait for ...

  • Actiontec electronic V.90 - page 30

    30 Default: 50 (1 second) S25 Detect DTR Change S25 defines the minimum amount of time that DTR has to remain of f before the modem performs the function specified by the &Dn command. A change in DTR that persists for a shorter time than that specified will be ignored by the modem. Range: 1-255 1/100 of a second Default: 5 (1/20 of a second) S3 ...

  • Actiontec electronic V.90 - page 31

    31 Appendix B: Communications Regulations FCC REGULA TIONS The following statements are provided in accordance with the Federal Communi- cations Commission (FCC) regulations. Please read these statements carefully before installing your modem. FCC P ART 68 REQUIREMENTS This equipment complies with Part 68 of the FCC Rules. On the bottom of this equ ...

  • Actiontec electronic V.90 - page 32

    32 DECLARA TION of CONFORMITY This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. This equipment generates, uses and can radiate radio frequency e ...

  • Actiontec electronic V.90 - page 33

    33 CANADIAN DEP AR TMENT OF COMMUNICA TIONS (CDOC): Requirements for End Users: Notice: The Canadian Department of Communications label identifies certified equipment. This certification means the equip- ment meets certain telecommunications network requirements. The Department does not guarantee the equipment will operate to the user  s satisfa ...

メーカー Actiontec electronic カテゴリー Fax Machine

Actiontec electronic V.90のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- V.90の取扱説明書
- Actiontec electronicの製品カード
- パンフレット
- またはActiontec electronic V.90の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Actiontec electronic V.90の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Actiontec electronic V.90の取り付け説明書、サービスマニュアル、簡易説明書、またはActiontec electronic V.90のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Actiontec electronic V.90の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Actiontec electronic V.90デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがActiontec electronic V.90を使用するのを助ける技術的文書のことです。説明書は通常、全てのActiontec electronic V.90ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Actiontec electronicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Actiontec electronic V.90の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははActiontec electronic V.90の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Actiontec electronic V.90に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Actiontec electronic V.90デバイスの基本機能を使うにあたってのヒント。 Actiontec electronic V.90のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Actiontec electronic V.90に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるActiontec electronic V.90のメーカー/サービスへの連絡先に関する情報。

Actiontec electronic V.90についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもActiontec electronic V.90の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがActiontec electronic V.90で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)