Stoelting 4231Gの取扱説明書

43ページ 1.27 mb
ダウンロード

ページに移動 of 43

Summary
  • Stoelting 4231G - page 1

    Model 4231G/H OWNER'S MANUAL Manual No. 513534 Apr . 2003, Rev . 3 ...

  • Stoelting 4231G - page 2

    ...

  • Stoelting 4231G - page 3

    Need Part s or Service? We stock the parts you need.  Our Technicians are factory trained and are certified in the Stoelting Technicare program. Model No.: _______________________ Serial No.: _______________________ Purchase Date: ____________________ Start-Up Date:____________________ CALL Distributor: _________________________ Phone No.: _____ ...

  • Stoelting 4231G - page 4

    ...

  • Stoelting 4231G - page 5

    STOELTING OWNER'S MANUAL FOR MODEL 4231G STOELTING FLOOR GRAVITY FREEZER SOFT-SERVE This manual provides basic information about the freezer. Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail. We reserve the right to make changes at any time without notice to ...

  • Stoelting 4231G - page 6

    ...

  • Stoelting 4231G - page 7

    T ABLE OF CONTENTS Section Description Page 1 INTRODUCTION ................................................................................................. 1 1.1 Description ........................................................................................................... 1 1.2 Specifications .............................................. ...

  • Stoelting 4231G - page 8

    LIST OF ILLUSTRA TIONS Figure Description Page 1 Model 4231G Freezer ....................................................................................................... 1 2 Specifications ................................................................................................................ .... 1 3 Warning and Label Locations ........ ...

  • Stoelting 4231G - page 9

    1 1.1 DESCRIPTION The Stoelting® 4231G freezer is gravity fed. The freezer is equipped with fully automatic controls to provide a uniform product. The freezer is designed to operate with almost any type of commercial soft serve or non- dairy mixes available, including ice milk, ice cream, yogurt, and frozen dietary desserts. This manual is designe ...

  • Stoelting 4231G - page 10

    2 1.2 SPECIFICATIONS MODEL 4231G FLOOR MODEL GRAVITY FREEZER DIMENSIONS Freezer: 25.90” (65.81 cm) wide x 30.20” (76.7 cm) deep x 60.80” (154.4 cm) high Crated: 38.00” (96.5 cm) wide x 64.00” (162.5 cm) deep x 70.00” (178.0 cm) high WEIGHT Freezer: 640 lbs. (291 kg) Crated: 815 lbs. (370 kg) ELECTRICAL Refer to the nameplate located on ...

  • Stoelting 4231G - page 11

    3 2.1 SAFETY PRECAUTIONS SECTION 2 INST ALLA TION INSTRUCTIONS Figure 3. Warning Label Locations Do not attempt to operate the freezer until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. Take notice of all warning labels on the freezer (Fig. 3). The labels have been put there to ...

  • Stoelting 4231G - page 12

    4 2.2 SHIPMENT AND TRANSIT The freezer has been assembled, operated and inspected at the factory. Upon arrival at the final destination, the freezer must be checked for any damage that may have occurred during transit. With the method of packaging used, the freezer should arrive in excellent condition. THE CARRIER IS RESPONSIBLE FOR ALL DAMAGE IN T ...

  • Stoelting 4231G - page 13

    5 C . Accurate leveling is necessary for correct drainage of freezer barrel to insure correct over-run and flow . Place a spirit level on top of the freezer at each corner to check for level condition (Fig. 5). If adjustment is necessary , level the freezer by turning the casters in or out (Fig. 6). Figure 6. Caster Adjustment Figure 7. Connecting ...

  • Stoelting 4231G - page 14

    6 ...

  • Stoelting 4231G - page 15

    7 SECTION 3 INITIAL SET -UP AND OPERA TION 3.1 OPERATOR’S SAFETY PRECAUTIONS SAFE OPERATION IS NO ACCIDENT; Observe these rules: A. Know the freezer . Read and understand the Operating Instructions. B. Notice all warning labels on the freezer . C. W ear proper clothing. Avoid loose fitting garment s, and remove watches, rings or jewelry , which c ...

  • Stoelting 4231G - page 16

    8 A. SPIGOT SWITCH When the spigot handle is opened the SPIGOT switch will start the auger drive motor and refrigeration systems. When the spigot handle is closed, the auger drive motor and compressor will remain on until the product in the barrel reaches the proper consistency . B. CLEAN-OFF-SERVE SWITCH The CLEAN-OFF-SERVE switch is a three-posit ...

  • Stoelting 4231G - page 17

    9 3.3 SANITIZING Sanitizing must be done after the freezer is clean and just before the hopper is filled with mix. Sanitizing the night before is not effective. However, you should always clean the freezer and parts after using it. W ARNING THE UNITED ST A TES DEP ARTMENT OF AGRICUL TURE AND THE FOOD AND DRUG ADMINISTRA TION REQUIRE THA T ALL CLEAN ...

  • Stoelting 4231G - page 18

    10 E. After five minutes, place the bucket under the spigots and open all three spigots to drain the sanitizing solution. When the solution has drained, place the CLEAN-OFF-SERVE switch in the OFF position. Allow the freezer barrel to drain completely (Fig. 14). Figure 14. Spigot Opened and Solution Draining 3.4 FREEZE DOWN AND OPERATION This secti ...

  • Stoelting 4231G - page 19

    11 I. The freezer is designed to dispense the product at a reasonable draw rate. If the freezer is overdrawn, the result is a soft product or a product the will not dispense at all. If this should occur , allow the freezer to run for approximately 30 seconds before dispensing additional product. After a while the operator will sense or feel the fre ...

  • Stoelting 4231G - page 20

    12 B . Place the CLEAN-OFF-SERVE rocker switch in the CLEAN position. Allow the mix to agitate in freezer barrel until the mix has become a liquid. C . Drain the liquid mix by opening the spigot. A bucket or container should be placed under the spigot to catch the liquid mix (Fig. 19). Figure 19. Draining Mix D . Place the CLEAN-OFF-SERVE switch in ...

  • Stoelting 4231G - page 21

    13 C . Remove rosette cap. Push the spigot body through the bottom of the front door and remove the spigot body (Fig. 22). Figure 21. Removing Front Door D . Remove the front auger supports and bearings (Fig. 23). Figure 22. Removing Spigot Figure 23. Removing Auger Supports E. Remove the auger assemblies from the freezer . Pull the augers out of t ...

  • Stoelting 4231G - page 22

    14 J . Remove drain trays. 3.9 CLEANING THE FREEZER PARTS Place all loose parts in a pan or container and take to the wash sink for cleaning. To clean freezer parts refer to the following steps: A. Place all p art s in warm mild detergent water and clean with brushes provided. Rinse all parts with clean hot water . CAUTION DO NOT DAMAGE P ARTS BY D ...

  • Stoelting 4231G - page 23

    15 CAUTION DO NOT PLACE THE MIX INLET REGULA T OR INT O THE HOPPER BEFORE INST ALLING THE AUGER. E. Install the two plastic flights onto rear of the auger and insert part way into freezer barrel. F . Install the remaining plastic flights, push the auger into the freezer barrel and rotate slowly until the auger engages the drive shaft. G. Install th ...

  • Stoelting 4231G - page 24

    16 NOTE Refer to Section 3.3 for sanitizing the assembled freezer before filling with mix. L. Install the drain trays (Fig. 30). CAUTION DRAIN TRA YS MUST BE IN PLACE BEFORE OPERA TING FREEZER TO PREVENT DAMAGE FROM POSSIBLE AUGER SEAL LEAKS. Figure 30. Drain Trays 3.12 ROUTINE CLEANING To remove spilled or dried mix for the freezer exterior, simpl ...

  • Stoelting 4231G - page 25

    17 SECTION 4 MAINTENANCE INSTRUCTIONS 4.1 PREVENTIVE MAINTENANCE It is recommended that a preventive maintenance schedule be followed to keep the freezer clean and operating properly. The following steps are suggested as a preventive maintenance guide. W ARNING NEVER A TTEMPT T O REP AIR OR PERFORM MAINTENANCE ON FREEZER UNTIL THE MAIN ELECTRICAL P ...

  • Stoelting 4231G - page 26

    18 C. MONTHL Y 1. Check drive belt for wear . 2. Check condenser for dirt. 4.2 FREEZE-UP If a freeze-up does occur, use the following steps to thaw the mix in the freezer barrel: CAUTION IF THE DRIVE BEL T SQUEALS WHEN THE CLEAN-OFF-SERVE SWITCH IS PLACED IN THE SERVE POSITION, OR WHEN THE SPIGOT IS OPENED TO DISPENSE PRODUCT , TURN THE CLEAN-OFF-S ...

  • Stoelting 4231G - page 27

    19 4.5 TROUBLESHOOTING W ARNING NEVER A TTEMPT TO REP AIR OR PERFORM MAINTENANCE ON FREEZER UNTIL THE MAIN ELECTRICAL POWER HAS BEEN DISCONNECTED. Problem Possible Cause Remedy Freezer does not run 1. Power to freezer is off. 1. Supply power to freezer 2. Fuse or circuit breaker is blown or tripped. 2. Replace or reset. (If condition continues See ...

  • Stoelting 4231G - page 28

    20 Low overrun 1. Mix inlet regulator (carburetor) missing. 1. Replace mix inlet regulator (carburetor). 2. Mix inlet regulator (carburetor) “O” Ring 2. Replace mix inlet regulator missing. (carburetor) “O” Ring. 3. Mix inlet regulator (carburetor) air tube 3. Clean with sanitizer brush. blocked. Front door leaks. 1. Front door knobs are lo ...

  • Stoelting 4231G - page 29

    21 SECTION 5 REPLACEMENT P ARTS 5.1 HOW TO ORDER PARTS To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information: A . Model number of equipment. B . Serial number of model, stamped on nameplate. Part Number Description 324014 Decal Black Arrow 324141 Decal Caution Rotating Blades 324509 D e ...

  • Stoelting 4231G - page 30

    22 ...

  • Stoelting 4231G - page 31

    23 Item Stoelting PN Qty Description 1 2177428 1 Door w/pins 2 3159696 2 Spigot, Outside 3 3158086 1 Spigot, Center 4 624598 4 O-Ring, 7/8 OD x 1/8 CS 5 624664 1 O-Ring 1-5/16 OD x 1-1/16 ID x 1/8 CS 6 625133 2 O- Ring 4.00" OD x .1875" CS 7 508135 As Reqd Lube, Petro-Gel 8 482019 4 Knob with 3/8-16 (Black) 9 624614 2 O-Ring, 1 OD x ¾ ID ...

  • Stoelting 4231G - page 32

    24 ...

  • Stoelting 4231G - page 33

    25 ...

  • Stoelting 4231G - page 34

    26 ...

  • Stoelting 4231G - page 35

    27 Item Stoelting PN Qty Description 1 152294 4 Belt V, 39.2 O.L. x 38.3 P.L. 2 282021-SV 2 Compressor (4231-18G, -38G) 2A 282020-SV 2 Compressor (4231-109G, -309G) 2B 282030 2 Compressor (4231-102G, -302G) 3 422156 2 Grommet Kit with sleeves 4 644371 8 Screw Cap 5/16-18 x 1-3/4 Hx 5 767211 8 Washer Flat 5/16, 7/8 x 3/8 x 14GA 6 522844 2 Motor, 2HP ...

  • Stoelting 4231G - page 36

    28 ...

  • Stoelting 4231G - page 37

    29 Item Stoelting PN Qty Description 1 649109 4 Screw Tap 10-16 x 1/2 Ind. Hx 2 524091 2 Mount Adhesive Back 1 x 1 Plastic 3 647885 2 Screw Mach 1/4-20 x 1/2 Trs Hd 4 538922 2 Nut Speed 1/4-20 5 766964 6 Washer Shakeproof 1/4 Zinc 6 644195 4 Screw Cap 1/4-20 x 2 Hx Hd 7 1172773 4 Spacer, 1.47 Long 8 2158124-SV 1 Door Interlock Switch Assy 9 766949 ...

  • Stoelting 4231G - page 38

    30 12, 13, 14 7 8 10 11 8 10 11 4A 4A 6 1, 2A, 2B 16 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 . . . . . 1 1 1 1 1 . . . . . . . . . . , , , , , 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 12, 13, 14 12, 13, 14 12, 13, 14 3 15 9 9 6 1, 2A, 2B 15 3 16 7 7 7 7 7 7 7 7 7 7 7 , , , , , 7 7 7 7 7 . . . . . / / / / / 5 5 5 5 5 0 0 0 0 0 , , ...

  • Stoelting 4231G - page 39

    31 Item Stoelting PN Qty Description 1 282021-SV 2 Compressor (4231-18G, -38G) 2A 282020-SV 2 Compressor (4231-109G, -309G) 2B 282030 2 Compressor (4231-102G, -302G) 3 4172774 1 Hopper & Evaporator Assembly 4 284104 2 Condenser (W/C Only) 4A 284044 1 Condenser (A/C Only) 5 718686 2 Swit ch Pressure (W/C Only) 6 342008 2 Drier, Filter 7 762277 2 ...

  • Stoelting 4231G - page 40

    32 12, 13, 14 7 8 10 11 8 10 11 4 4 6 1, 2A, 2B 16 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 . . . . . 1 1 1 1 1 . . . . . , , , , , 3 3 3 3 3 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 12, 13, 14 12, 13, 14 12, 13, 14 3 15 9 9 6 1, 2A, 2B 15 3 16 7 7 7 7 7 7 7 7 7 7 7 , , , , , 7 7 7 7 7 . . . . . / / / / / 5 5 5 5 5 . . . . . , , , , , 2 2 2 ...

  • Stoelting 4231G - page 41

    33 Item Stoelting PN Qty Description 1 282021-SV 2 Compressor (4231-18G, -38G) 2A 282020-SV 2 Compressor (4231-109G, -309G) 2B 282030 2 Compressor (4231-102G, -302G) 3 4172774 1 Hopper & Evaporator Assembly 4 284104 2 Condenser (W/C Only) 4A 284044 1 Condenser (A/C Only) 5 718686 2 Switch Pressure (W/C Only) 6 342008 2 Drier, Filter 7 762277 2 ...

  • Stoelting 4231G - page 42

    ...

  • Stoelting 4231G - page 43

    W ARRANTY SOFT SER VE / SHAKE FREEZERS 1. Scope: Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors, speed reducers, auger and auger flights of Stoelting soft serve / shake freezers will be free from defects in materials and workmanship under normal use and proper maintenance a ...

メーカー Stoelting カテゴリー Freezer

Stoelting 4231Gのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 4231Gの取扱説明書
- Stoeltingの製品カード
- パンフレット
- またはStoelting 4231Gの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Stoelting 4231Gの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Stoelting 4231Gの取り付け説明書、サービスマニュアル、簡易説明書、またはStoelting 4231Gのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Stoelting 4231Gの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Stoelting 4231Gデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがStoelting 4231Gを使用するのを助ける技術的文書のことです。説明書は通常、全てのStoelting 4231Gユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Stoeltingの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Stoelting 4231Gの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははStoelting 4231Gの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Stoelting 4231Gに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Stoelting 4231Gデバイスの基本機能を使うにあたってのヒント。 Stoelting 4231Gのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Stoelting 4231Gに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるStoelting 4231Gのメーカー/サービスへの連絡先に関する情報。

Stoelting 4231Gについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもStoelting 4231Gの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがStoelting 4231Gで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)