-
Omega CCT-80 Series - page 1
M2218/1201 http://www.omega.com e-mail: info@omega.com ® U ser ’ s Guide CCT -80 Strain Gage Signal Conditioners ...
-
Omega CCT-80 Series - page 2
Servicing North America: USA: One Omega Drive, Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 Tel: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 Tel: (514) 856-6928 FAX: (514) 856-6886 e-mail: canada@omega.com For immediate technical or application assistance: USA and Canada: Sales Service: ...
-
Omega CCT-80 Series - page 3
NOTES T ABLE OF CONTENTS PAGE Open the Housing . . . . . . . . . . . . . . . . . . . . . . . . 3 Internal Overview . . . . . . . . . . . . . . . . . . . . . . . . 3 Power Supply module MA . . . . . . . . . . . . . . . . . . 4 Changing the Power Supply . . . . . . . . . . . . . . . . 4 Signal Output module MS . . . . . . . . . . . . . . . . . . 5 Ch ...
-
Omega CCT-80 Series - page 4
PROCEDURE 1. Insert a screwdriver or similar tool in the points marked c . 2. Turn the screwdriver until the case walls begin to separate towards A and B , so the two side lugs e , are free. 3. Grab the Signal Conditioner body, at the points marked d ‚ and pull it towards C , until the two side lugs e are out of their housing and the internal cir ...
-
Omega CCT-80 Series - page 5
- +10 Vdc FIG.10 350 Ω + - + - POWER SUPPLY The side label, shows the type and value of the power supply. SIGNAL OUTPUT Current SIGNAL OUTPUT Voltage POWER SUPPLY OUTPUTS / SALIDAS m A Vdc INPUT / ENTRADA SU PPL Y / ALIMENT ACION 3 4 5 6 9 10 1 1 12 7 1 + Lo H i + -- OUTPUTS SAL I DAS AC VO L TAG E 3 4 5 6 1 2 POWER SU PPL Y FUENTE ALI M EN T ACI ...
-
Omega CCT-80 Series - page 6
FIG.8 "MP" input board PT1 SIGNAL INPUT RANGE SELECTION The "MP" input board for this signal conditioner, does not have jumpers because it allows only one signal input (0 to 20 mV). To calibrate the signal conditioner, follow the adjustment and calibration procedure. The user can field adjust the tare using the trim- mer PT1, lo ...
-
Omega CCT-80 Series - page 7
INPUT STANDARD SIGNAL 20 mV TARE by internal trimmer PT1, located on the "MP" input board OUTPUT 0 to 20 mA or 4 to 20 mA R L < 600 Ω max. 22 mA ±3% 0 to 10 Vdc R L > 1000 Ω max. 11 V ±3% ACCURACY ≤ 0.2 % FS RESPONSE TIME ≤ 250 mS GALVANIC ISOLATION Input, Output and Power Supply are all isolated to 2 kVeff . 50 Hz/1 m. GE ...
-
Omega CCT-80 Series - page 8
INPUT STANDARD SIGNAL 20 mV TARE by internal trimmer PT1, located on the "MP" input board OUTPUT 0 to 20 mA or 4 to 20 mA R L < 600 Ω max. 22 mA ±3% 0 to 10 Vdc R L > 1000 Ω max. 11 V ±3% ACCURACY ≤ 0.2 % FS RESPONSE TIME ≤ 250 mS GALVANIC ISOLATION Input, Output and Power Supply are all isolated to 2 kVeff . 50 Hz/1 m. GE ...
-
Omega CCT-80 Series - page 9
FIG.8 "MP" input board PT1 SIGNAL INPUT RANGE SELECTION The "MP" input board for this signal conditioner, does not have jumpers because it allows only one signal input (0 to 20 mV). To calibrate the signal conditioner, follow the adjustment and calibration procedure. The user can field adjust the tare using the trim- mer PT1, lo ...
-
Omega CCT-80 Series - page 10
- +10 Vdc FIG.10 350 Ω + - + - POWER SUPPLY The side label, shows the type and value of the power supply. SIGNAL OUTPUT Current SIGNAL OUTPUT Voltage POWER SUPPLY OUTPUTS / SALIDAS m A Vdc INPUT / ENTRADA SU PPL Y / ALIMENT ACION 3 4 5 6 9 10 1 1 12 7 1 + Lo H i + -- OUTPUTS SAL I DAS AC VO L TAG E 3 4 5 6 1 2 POWER SU PPL Y FUENTE ALI M EN T ACI ...
-
Omega CCT-80 Series - page 11
PROCEDURE 1. Insert a screwdriver or similar tool in the points marked c . 2. Turn the screwdriver until the case walls begin to separate towards A and B , so the two side lugs e , are free. 3. Grab the Signal Conditioner body, at the points marked d ‚ and pull it towards C , until the two side lugs e are out of their housing and the internal cir ...
-
Omega CCT-80 Series - page 12
NOTES T ABLE OF CONTENTS PAGE Open the Housing . . . . . . . . . . . . . . . . . . . . . . . . 3 Internal Overview . . . . . . . . . . . . . . . . . . . . . . . . 3 Power Supply module MA . . . . . . . . . . . . . . . . . . 4 Changing the Power Supply . . . . . . . . . . . . . . . . 4 Signal Output module MS . . . . . . . . . . . . . . . . . . 5 Ch ...
-
Omega CCT-80 Series - page 13
WARRANTY / DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers recei ...
-
Omega CCT-80 Series - page 14
Where Do I Find Everything I Need for Process Measurement and Control? OM EGA…Of Course! TEMPERATURE M U Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies M U Wire: Thermocouple, RTD & Thermistor M U Calibrators & Ice Point References M U Recorders, Controllers & Process Monitors M U Infrared Pyrometers PR ...
Omega CCT-80 Seriesについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもOmega CCT-80 Seriesの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがOmega CCT-80 Seriesで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。