Zebra 2844の取扱説明書

38ページ 8.19 mb
ダウンロード

ページに移動 of 38

Summary
  • Zebra 2844 - page 1

    User’s Manual No. 980348-001 Rev. A ©2001 Zebra Technologies Corporation 2844 Thermal Printer User’s Manual ...

  • Zebra 2844 - page 2

    ii 980348-001 Rev. A ...

  • Zebra 2844 - page 3

    FOREWORD This manual provides installation and operation information for the LP 2844 and the TLP 2844 series printers, manufactured by Zebra Technologies Corporation, Camarillo, California. COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation. This docu - ment and the information contained within is copy ...

  • Zebra 2844 - page 4

    SHOCK HAZARD WARNING: The printer and power supply should never be operated in a location where either one can get wet. Personal injury could result. MEDIA AND RIBBON WARNING: Always use high quality, approved labels, tags and ribbons. If adhesive backed labels are used that DO NOT lay flat on the backing liner, the exposed edges may stick to the l ...

  • Zebra 2844 - page 5

    980348-001 Rev. A v TABLE OF CONTENTS Installation and Operation . . . . . . . . . . . . . . . . . . 1 Unpack Your Printer . . . . . . . . . . . . . . . . . . . . . . 2 Know Your Printer . . . . . . . . . . . . . . . . . . . . . . . 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AutoSense Media Gap Sensing . . . . . . . . . ...

  • Zebra 2844 - page 6

    vi 980348-001 Rev. A ...

  • Zebra 2844 - page 7

    1 Installation and Operation This section provides information on the installation and operation of the printer. The printer is a low cost, desktop thermal printer. The printer is specifically designed for printing labels, tags or continuous receipts (with or without bar codes) from any DOS™, Win- dows™or ASCII-based compatible host. There are ...

  • Zebra 2844 - page 8

    Unpack Your Printer Know Your Printer 2 980348-001 Rev. A Installation and Operation ...

  • Zebra 2844 - page 9

    980348-001 Rev. A 3 Installation and Operation ...

  • Zebra 2844 - page 10

    Installation The following steps will guide you through the installation of the printer and software. Step ➊ Attach Power Supply To The Printer See the SHOCK HAZARD WARNING on page iv. 4 980348-001 Rev. A Installation and Operation Power OFF Check Voltage Plug in Power Module Plug in Power Cord Plug Power Cord into a Suitable AC Outlet ...

  • Zebra 2844 - page 11

    Step ➋ Attach Interface Cable See Appendix A for cable wiring information. 980348-001 Rev. A 5 Installation and Operation Parallel Serial Universal Serial Bus (USB) ...

  • Zebra 2844 - page 12

    Step ➌ Load Media 6 980348-001 Rev. A Installation and Operation Power ON Open Cover Open Guides MO VIE ...

  • Zebra 2844 - page 13

    Load Media - continued 980348-001 Rev. A 7 Installation and Operation Remove the outside length of media For more infor - mation on media preparation, refer to Appendix A. MO VIE Install Roll Note: Find the instructions for preparing media in Appendix A. Close Guides to the Width of the Media Note: When using linerfree labels, adjust the guides to ...

  • Zebra 2844 - page 14

    Load Media - continued 8 980348-001 Rev. A Installation and Operation MO VIE Release Cover Note: This step applies to thermal transfer printers Close Cover ...

  • Zebra 2844 - page 15

    Step  AutoSense Media Gap Sensing Perform this procedure when loading a new roll. If your printer has the label dispenser option, turn OFF the label taken sensor. 980348-001 Rev. A 9 Installation and Operation MO VIE Power OFF Hold Feed Button Power ON ...

  • Zebra 2844 - page 16

    AutoSense Gap Sensor Adjustment - continued If the indicator remains orange or red, see the troubleshooting steps. 10 980348-001 Rev. A Installation and Operation When Indicator Flashes, Release Feed Button UKQ1935 16 V3.21 Serial port : 96,N,8,1 Image buffer size:1032K Fmem:000.0K,016.4K avl Gmem:000K,0593K avl E I8,0,001 rY S2 D10 R016,000 ZT UN ...

  • Zebra 2844 - page 17

    Step ➎ Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980348-001 Rev. A 11 Installation and Operation ...

  • Zebra 2844 - page 18

    Operation The following information helps you get the most from your printer. Programming Commands You must use programming to control many of the printer's functions. See the EPL2 program - mer's manual for details. For example, the Q command controls form length and gap. Printer Driver The printer driver provides a convenient control to ...

  • Zebra 2844 - page 19

    2 Using Options This section provides information on the printer's optional features: • thermal transfer printing • label dispenser • fan-fold media • media cutter 980348-001 Rev. A 13 Using Options ...

  • Zebra 2844 - page 20

    Using Transfer Ribbon The TLP printer supports both direct thermal media (chemically treated to darken when heated) and thermal transfer media (accepts wax and/or resin transferred off a ribbon). Step ➊ Prepare Ribbon 14 980348-001 Rev. A Using Options Pull Adhesive Strip Free MO VIE ...

  • Zebra 2844 - page 21

    Step ➋ Install Supply Roll 980348-001 Rev. A 15 Using Options Press onto Hub Thread Ribbon Through Carriage Align Notches onto Hub Spokes ...

  • Zebra 2844 - page 22

    Step ➌ Install Take-Up Core 16 980348-001 Rev. A Using Options Press onto Hub Align Notches onto Hub Spokes ...

  • Zebra 2844 - page 23

    Step ➍ Tighten Ribbon When using ribbon, make sure you also use thermal transfer media. 980348-001 Rev. A 17 Using Options Attach Ribbon to Take-Up Core Note: Use the adhesive strip on new rolls; otherwise, use tape Remove Slack From Ribbon ...

  • Zebra 2844 - page 24

    Adding a New Transfer Ribbon If ribbon runs out in the middle of a print job, the indicator lights orange and the printer waits for you to add a fresh roll. Keep the power on as you change ribbon. Open the top cover, then cut the used ribbon so you can remove the cores. Load a new ribbon roll (refer to the previ - ous procedure if necessary). Close ...

  • Zebra 2844 - page 25

    Using the Label Dispenser 980348-001 Rev. A 19 Using Options Open Door Switch On the Label Taken Sensor Remove Several Labels Push Liner Through Slot Close Door Close Top Cover and Press Feed Button MO VIE ...

  • Zebra 2844 - page 26

    Using Fan-Fold Media 20 980348-001 Rev. A Using Options Insert Media Adjust Holders to Width of Media Tighten Screw (use a small Phillips driver #1) Adjust Guides to Width of Media ...

  • Zebra 2844 - page 27

    Using the Media Cutter Printers that have a bezel with a motorized blade can dispense one or more forms that are then automatically cut from the media supply. This option cuts through continuous paper from rolls and liner between labels. The media can be up to 0.0055 inch (0.095mm) thick, 1.12 inch (28mm) to 4.25 inches (108mm) wide, and at least 0 ...

  • Zebra 2844 - page 28

    Clearing the Media Cutter If the blade cuts through labels, adhesive can jam the cutter. Turn OFF (O) printer power and unplug the power and interface cables before clearing the cutter. Keep the cutter dry. Never use any solutions or solvents to clean the blade. After removing debris, plug in the power and interface cables, turn on the printer, the ...

  • Zebra 2844 - page 29

    Appendix A - Troubleshooting Problem Solution or Reason STATUS Indicator Does not light after turning ON ( I ) printer. 1. Check power connections from A.C. outlet to power supply to printer. 2. Check that media or ribbon is present. Blinks GREEN. 1. Printer receiving data through interface. 2. Signal to begin AutoSense after turning ON printer. Re ...

  • Zebra 2844 - page 30

    Problem Solution or Reason Printer Operation--continued Printer appears to be working (media is being fed out), but nothing is printed. 1. Verify that the labels are the correct type. 2. Check that the roll is loaded with the di - rect thermal side facing up. 3. Clean the print head with cleaning pen. 4. Ensure top cover is locked closed. Printing ...

  • Zebra 2844 - page 31

    Troubleshooting Media Handling Problem Solution or Reason Label Dispenser Printing continues between labels. 1. Make sure label-taken sensor is on. 2. The label-taken sensor is blocked or dirty. Remove any scraps or dust. 3. Continuous media may be set. Verify form length setting through program - ming Q command. See the EPL2 pro - grammer's m ...

  • Zebra 2844 - page 32

    Serial Interface Cable Wiring The figure below displays the cable wiring required to use the printer's RS-232 serial interface. 26 980348-001 Rev. A Appendix A - Troubleshooting N/C RxD TxD DTR GND DSR RTS RI CTS Pri nter Hos t 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 DB -9 Pi n # DB -9 Pi n # F ema le DB-9 to M ale DB-9 Cable P/N 300017-006 ( 6&ap ...

  • Zebra 2844 - page 33

    Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. KDU or scanner) 980348-001 Rev. A 27 Appendix A - Troubleshooting PRINTER DB - 25 Pi n No . Centroni cs Pi n No . F e m a l eD B - 2 5t oM a l eC e n t r o n i c s ...

  • Zebra 2844 - page 34

    Universal Serial Bus (USB) The table below provides the contact terminat - ing assignments by number and electrical value for the cable connectors. Contact Number Signal Name Typical Wiring Assignment 1 VBUS Red 2 D- White 3 D+ Green 4 GND Black Shell Shield Drain Wire You can refer to the Universal Serial Bus Speci- fication for details regarding ...

  • Zebra 2844 - page 35

    Cleaning the Print Head When you load new media, you can also clean the print head. Turn OFF (O) the printer before performing this procedure . 980348-001 Rev. A 29 Appendix A - Troubleshooting Rub Cleaning Pen Across Dark Area of Print Head Wait One Minute Before Closing Printer Do Not Clean Roller With Cleaning Pen MO VIE ...

  • Zebra 2844 - page 36

    Cleaning the Platen The platen, over time, picks up adhesive and dust which requires occasional cleaning. To follow these steps, you require a clean, lint-free cloth lightly moistened with isopropyl alcohol. Turn OFF (O) the printer before performing this procedure. Let the platen dry for at least one minute before loading media. 30 980348-001 Rev. ...

  • Zebra 2844 - page 37

    Preparing Media, Paper, and Labels Before Loading During shipment, the outside length of media may become dirty when handled or dusty when stored. A preparation before loading media makes sure both the print head and platen stay cleaner for more time. You must avoid dragging adhesive or dirty media between the print head and platen. Such an occuran ...

  • Zebra 2844 - page 38

    980348 - 001 A ...

メーカー Zebra カテゴリー Printer

Zebra 2844のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2844の取扱説明書
- Zebraの製品カード
- パンフレット
- またはZebra 2844の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Zebra 2844の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Zebra 2844の取り付け説明書、サービスマニュアル、簡易説明書、またはZebra 2844のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Zebra 2844の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Zebra 2844デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがZebra 2844を使用するのを助ける技術的文書のことです。説明書は通常、全てのZebra 2844ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Zebraの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Zebra 2844の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははZebra 2844の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Zebra 2844に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Zebra 2844デバイスの基本機能を使うにあたってのヒント。 Zebra 2844のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Zebra 2844に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるZebra 2844のメーカー/サービスへの連絡先に関する情報。

Zebra 2844についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもZebra 2844の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがZebra 2844で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)