-
Pelco 10P08 - page 1
IOP08 Series Inter cept ® Camera and Lens Installation/ Operation Manual C1441M-D (1/98) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 ® ...
-
Pelco 10P08 - page 2
2 Pelco Manual C1441M-D (1/98) CONTENTS Section Page 1.0 GENERAL3 1.1 IMPORT ANT SAFEGUARDS AND WARNINGS ............................... 3 2.0 DESCRIPTION .......................................................................................... 4 2.1 MODELS ........................................................................................... ...
-
Pelco 10P08 - page 3
Pelco Manual C1441M-D (1/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by Qualified S ...
-
Pelco 10P08 - page 4
4 Pelco Manual C1441M-D (1/98) 2.0 DESCRIPTION The IOP08 Series of cameras and lenses is part of the IDS08 Intercept ® Series of domes. The IDS08 Series is an integral system that includes a back box (BB08), dome drive (DD08), dome receiver/driver (DRD08), and imager/optics package (IOP08). For installation and operation instructions for the back ...
-
Pelco 10P08 - page 5
Pelco Manual C1441M-D (1/98) 5 3.0 INST ALLA TION The camera and lens package are installed at the factory . 3.1 ADJUSTMENTS Y our optics package comes from the factory adjusted for a broad range of lighting conditions. For this reason, you may find it necessary to adjust your optics package to tailor the picture to your specific viewing environmen ...
-
Pelco 10P08 - page 6
6 Pelco Manual C1441M-D (1/98) ➤ Auto Iris Level is adjusted using a video meter to provide a video signal output of be- tween 130 and 142 IRE (Institute of Radio Engineers; 1V p–p = 100 IRE’s) when lighting from skylights, low pressure sodium lights and fluorescent lights are present. ALC is adjusted to the midpoint between Peak and A verage ...
-
Pelco 10P08 - page 7
Pelco Manual C1441M-D (1/98) 7 3.1.5 V -Phase (V er tical Phase) V -Phase (V ertical Phase) is valuable when multiple optic packages are switched by a sequential or matrix switcher . The vertical phase +/- buttons are used to compen- sate for vertical phase discrepancies which will occur in a multiple camera environ- ment. In this type of environme ...
-
Pelco 10P08 - page 8
8 Pelco Manual C1441M-D (1/98) Figure 3. Black and White Camera Adjustments T able A. Shutter Speeds Shutter Shutter Speed Position (in seconds) 0 1/60 1 1/100 2 1/250 3 1/500 4 1/1000 5 1/2000 6 1/4000 7 1/10,000 8 Not Used 9 Not Used SHUTTER SPEED CONTROL (YOU CAN SELECT ONE OF EIGHT SHUTTER SPEEDS; SEE T ABLE BELOW) USED IN CONJUNCTION WITH A WB ...
-
Pelco 10P08 - page 9
Pelco Manual C1441M-D (1/98) 9 4.0 SERVICE Should it become necessary to remove the camera/lens for service or replacement, follow the steps outlined below . Refer to Figure 4, if necessary . 1. Remove main electrical power by switching off main power switch located up inside the back box. 2. Rotate the tilt table so that it is level with the horiz ...
-
Pelco 10P08 - page 10
10 Pelco Manual C1441M-D (1/98) 5.0 WIRING DIAGRAM Figure 5. Schematic Diagram for Color Camera/Lens RED GREEN YELLOW BLACK GRAY WHITE BROWN BLUE RED VIOLET YELLOW BLACK GRAY WHITE BROWN BLUE BROWN WHITE GRAY BLACK YELLOW VIOLET BLUE RED WHT/RED WHT/BLK 10 1 1 8 J6 J7 J1 P2 1 10 12 1 P1 4 8 1 ORG/WHT GRN/WHT WHT/BLK WHT/RED 1 WHT/RED WHT/BLK ZOOM F ...
-
Pelco 10P08 - page 11
Pelco Manual C1441M-D (1/98) 11 6.0 SPECIFICA TIONS MECHANICAL Housing Construction: 0.050" aluminum Dimensions: 6.25" L x 4.25" H x 4.10" W (15.88 x 10.80 x 10.41 cm) ELECTRICAL Black/White (EIA) Camera Module Input Voltage: 24 VAC, 60 Hz Power Required: Less than 3 watts, plus auto iris of lens Video output: 1 V p–p, 75 ohms ...
-
Pelco 10P08 - page 12
12 Pelco Manual C1441M-D (1/98) 7.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1998, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defecti ...
Pelco 10P08についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもPelco 10P08の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco 10P08で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。