Poulan 530088886の取扱説明書

16ページ 0.59 mb
ダウンロード

ページに移動 of 16

Summary
  • Poulan 530088886 - page 1

    220 LE / 260 LE Operator’s Manual Manual del Operador Manuel de L’utilisateur WAR NI NG : Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so c an result in serious injury. ADVERT ENC IA : Lea el manual del operador y siga todas las advertencias e enstruc- ciones de seguridad. El no hacer lo p ...

  • Poulan 530088886 - page 2

    2 SAFETY RULES W ARNING: Alway s disconnect spark plug wi re and place wire where it can- not contact spark plug to prev ent acc idental starti ng when set ting up, transport ing, ad- justi ng or mak ing repairs exc ept carburetor adjustm ents. Becaus e a chain saw is a high-speed wood- cutti ng tool, special s afety prec autions mus t be observed ...

  • Poulan 530088886 - page 3

    3 marked c ontainer for all fuel purposes . Wipe up all fuel spills before starting s aw . S Move at least 10 feet (3 met ers) from fuel- ing sit e before s tarting engine. S Turn the engine off and l et saw cool in a non-combust ible area, not on dry leaves , straw, paper, etc. S lowly remove fuel c ap and refuel unit . S Store the unit and fuel i ...

  • Poulan 530088886 - page 4

    4 Thumb on underside of handlebar Elbow loc ked S Keep a good, firm grip on the saw with both hands when t he engine is running and don’t let go. A firm grip will help you reduce kick back and mai ntain cont rol of the saw. Keep the fingers of your lef t hand enc ir- cling and your left thumb under the front handlebar . Keep y our right hand c om ...

  • Poulan 530088886 - page 5

    5 and bar as origi nal equipment. Repairs on a chain brak e shoul d be m ade by an autho- rized servic ing dealer. T ake your unit to t he place of purchase if purc hased from a ser- vici ng deal er, or to t he neares t authori zed master s ervice deal er. S Tip contact i n some cases may cause a light - ning fast reverse REACTION, kicking t he gui ...

  • Poulan 530088886 - page 6

    6 S Replace t he chain brake nuts and tight en finger t ight. O nce the chain is tens ioned you will need to tight en c hain brake nut s. Mount the Bar Proper cha in direction Tip of Bar Place chain onto the sprocket CHAIN TENSION (Incl uding uni ts with chain already inst alled) NOTE: When adjusti ng c hain tensi on, make sure t he chain brake nut ...

  • Poulan 530088886 - page 7

    7 OPERA TION KNOW YOUR SA W READ THIS OPERA TOR ’S MANUAL AND SAFETY RULES BEFO RE OPERATIN G YOU R CHAIN SAW . Compare t he illustra tions with your unit to familiarize yourself with the location of the various controls and adjus tments. Save thi s manual f or future ref erence. Chain Adjust ment T ool (Bar T ool) Primer Bulb Fuel Mix Fill Cap S ...

  • Poulan 530088886 - page 8

    8 FUEL ING & LUBR ICATION W ARNING: Remove fu el ca p slow - ly when ref ueling. FUELING ENGINE This engi ne is certi fied t o operate on unleaded gasoline. B efore operation, gasoline mus t be mix ed wi th a good qualit y synthe tic 2- cycle air- cooled engine oil designed to be mix ed at a ratio of 40:1. Poulan/W eed E ater brand synt hetic o ...

  • Poulan 530088886 - page 9

    9 ON STOP ON/STOP SWITCH OFF FULL CHOKE/FAST IDLE LEVER Choke/Fast Idle Lever (SIDE VIEW ) ST ARTING A W ARM ENGINE: S Move ON/STOP swi tch to the ON posi tion. S Pull the choke/f ast idl e lever out to the full extent, then push t he l ever back in c om- pletely (to t he OFF posi tion). S Slowly pres s t he prim er bulb 6 ti mes. S Pull the st art ...

  • Poulan 530088886 - page 10

    10 S Keep the chain out of dirt and s and. E ven a small amount of dirt will qui ckly dull a chain and thus increa se the possibility of kick- back. S Practi ce cutt ing a few small logs us ing the following t echniques to get t he “feel” of us- ing your s aw before you begin a maj or sawing operati on. S Squeeze the thrott le trigger and al lo ...

  • Poulan 530088886 - page 11

    11 Opening of felling cut Closing of notch Hinge holds tree on s tump and helps control fall NOTE: Before felling cut is c omplete , use wedges t o open the cut when necessary to control the direction of f all. T o avoid kickbac k and chain damage, us e wood or plast ic wedges, but never steel or i ron wedges . S Be alert to signs that t he tree is ...

  • Poulan 530088886 - page 12

    12 S Finish wi th your s econd cut. 1 st Cut 2 nd Cut U s i n gal o gf o rs u p p o r t 2 nd Cut 1 st Cut 1 st Cut 2 nd Cut Using a support stand 1 st Cut 2 nd Cut LIMBING AND PRUNING W ARNING: Be alert f or and guard against kic kback. Do not allow the moving chain to contac t any other branc hes or ob- jects at the nos e of the gui de bar when li ...

  • Poulan 530088886 - page 13

    13 SERVICE W ARNING: Disc onnect t he spark plug before performing maint enance except for carburet or adjust ments. We recommend all servic e and adj ustments not l isted in t his m anual be performed by an authorized or Mast er S ervice Dealer. MAINTENANCE SCHEDULE Lubric ate bar sprocket hole After each use ....... Check: Fuel m ixture level Bef ...

  • Poulan 530088886 - page 14

    14 CARBURETOR ADJUSTMENTS Y our c arburetor is equipped wit h limiter caps. Carburet or adjus tment is a c ompli- cated task. W e recommen d that you take your unit to an Authoriz ed Serv ice Dealer. Damage wil l occur if you turn the needles be- yond the li miter s tops. BAR MAINTENANCE If your saw c uts to one s ide, has to be forc ed through the ...

  • Poulan 530088886 - page 15

    15 TROUBLE CAUSE REMEDY Engine will not start or w ill run only a few seconds af ter starti ng. S Ignition swit ch off. S Engine flooded. S Fuel tank empt y. S Spark plug not f iring. S Fuel not reaching carburetor . . S Move ign ition switch to ON. S See “Diff icult Start ing” in Operation Sec tion. S Fill tank with correct fuel m ixture. S In ...

  • Poulan 530088886 - page 16

    16 be designed, built , and equipped to meet the State’s stringent anti - - smog standards. POU- LAN /WEED EA TER must warrant th e emis - sion control system on your small off - - road en- gine f or the periods of t ime li sted below provided there has been no abuse, neglect, or improper maintenance of your small off- - road engine engine. Y our ...

メーカー Poulan カテゴリー Chainsaw

Poulan 530088886のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 530088886の取扱説明書
- Poulanの製品カード
- パンフレット
- またはPoulan 530088886の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Poulan 530088886の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Poulan 530088886の取り付け説明書、サービスマニュアル、簡易説明書、またはPoulan 530088886のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Poulan 530088886の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Poulan 530088886デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPoulan 530088886を使用するのを助ける技術的文書のことです。説明書は通常、全てのPoulan 530088886ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Poulanの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Poulan 530088886の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPoulan 530088886の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Poulan 530088886に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Poulan 530088886デバイスの基本機能を使うにあたってのヒント。 Poulan 530088886のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Poulan 530088886に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPoulan 530088886のメーカー/サービスへの連絡先に関する情報。

Poulan 530088886についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPoulan 530088886の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPoulan 530088886で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)