Clifford GP500の取扱説明書

28ページ 0.08 mb
ダウンロード

ページに移動 of 28

Summary
  • Clifford GP500 - page 1

    ...

  • Clifford GP500 - page 2

    ...

  • Clifford GP500 - page 3

    Main te nance Your GP500 system requires no maintenance except for replacement o f remote control batteries when they reach the end of their useful life. Fo r further information on this, see the Automatic low battery warning and Remot e control battery replacement sections on page 13. This product, like any electrical device on your motorcycle, re ...

  • Clifford GP500 - page 4

    Wel come to the world of high- technology ve hi cle se cu rity and con ven ience C ongratulations on the purchase of your GP500 motorcycle security/convenience system. Your re mote con trol s The weather resistant pair of remote controls that are provided with GP500 are ultra-sophisticated miniature radio transmitters powered by a single miniature ...

  • Clifford GP500 - page 5

    Re motely con trol ling your GP500 Each of your two remote controls can command several different functions . TO ARM : Press button I on the remote control. You wil l hear two chirp s and the indicator lights will flas h twice. The LED will flash repeatedly. TO DIS ARM : Press button I on the remote control. One chir p and one indicator light flash ...

  • Clifford GP500 - page 6

    TO AC TI VAT E IN STAN T AUTOARMIN G BYPASS : Press button III on the remote control and hold for three seconds. Two indicator light flashe s confirm that GP500 will NOT AutoArm. If you press and hold button III for three seconds onc e more, the system will respond with one indicator light flas h which means that AutoArming has been reactivated. Th ...

  • Clifford GP500 - page 7

    QUICK REF ER ENCE: RE MOTE CON TROL FUNC TIONS Functio n Press button(s ) Arm or dis ar m I Si lently arm or dis arm II In stant AutoArming By pass (press and hold but ton for three sec ond s while sys tem is dis armed ) III Dual- Level Piezo Sen sor Warn ing Level By pass (press but ton withi n 10 sec onds af ter arm ing the sys tem ) III Dual- Le ...

  • Clifford GP500 - page 8

    ACG-2™ (Anti- CodeGrabbing 2™) Clifford’s ACG-2 protects your motorcycle from thieves’ remote control “cloning” devices that are used to record the disarming code transmitted from your remote . Auto matic re mote con trol low- battery warn ing If your remote control battery is very low, you will hear five rapid chirps when you disarm ra ...

  • Clifford GP500 - page 9

    Two- Point In ter nal Im mo bi li sa tion Please be aware that the AutoArming feature has no effect o n Immobilisation. The system automatically immobilizes your vehicle’s starte r and ignition 30 seconds after engine shutdown or when you arm with th e remote control . When you remotely disarm your GP500 system, the Immobilisation circuits will a ...

  • Clifford GP500 - page 10

    AutoArming ™ If this feature is enabled and you forget to remotely arm. After 30 second s pass, the system is automatically armed. In instances where you want to bypass AutoArming, such as when fueling the motorcycle, simply turn th e ignition on and then off again after you have parked. Digi tal Dual- Zone Tilt/Mo tion Sen sor Clifford’s Digit ...

  • Clifford GP500 - page 11

    TO RE MOTELY BY PASS BOTH ZONES : During the first 10 seconds after arming the system remotely, simultaneously press buttons I I and III on the remote control and hold for three seconds. The system provides four indicator ligh t flashe s to indicate when the warning zone i s bypassed, and another four indicator light flashe s when both zones are by ...

  • Clifford GP500 - page 12

    TO RE MOTEL Y AD JUST THE DUAL- ZONE PIEZO SEN SOR: With the ig ni tion turned OFF. Press but tons I I and III si mul ta ne ously for three sec onds. Th e sys tem will re spond with one chir p . To adjust the warning level of the sensor, yo u must have the ignition turned ON, to adjust th e trigger level of the sensor, turn the ignition OFF. Then : ...

  • Clifford GP500 - page 13

    TO RE MOTELY BY PASS THE WARN ING ZONE: During the first 10 seconds after arming the system remotely, press button III on the remot e control. The system provides f our indicator ligh t flashes when the warning level is bypassed . TO RE MOTELY BY PASS BOTH ZONES : During the first 10 seconds after arming th e system remotely, press button III on th ...

  • Clifford GP500 - page 14

    False Alarm Pre ven tion & FACT ™ With Clifford’s patented FACT (False Alarm Control and Test) feature , you’ll never experience repeated false alarms. If the siren sounds, DO NO T remotely disarm the system; allow it to run for the full 30-second sire n duration. Before sounding the siren a second time, the system automatically checks fo ...

  • Clifford GP500 - page 15

    How to in ter pret the LED status in di ca tor LED Condition Meaning Of f Sys tem is dis arme d Flashing Steadil y (Ignition off ) Sys tem is arme d Flashing rapidl y (ignition off ) AutoArming Count dow n Flashing slowly (ignition on or off ) Sys tem is dis armed but Im mo bi li sa tion points are en gaged (see page 15 ) Pause between slow flashes ...

  • Clifford GP500 - page 16

    Smart Au toTest ing ™ Each time you remotely arm the system, it tests all triggers and sensors. Fo r example, if the Helmet Theft Prevention System is active, you will receiv e the usual 2 chirps and flashes , then , 5 seconds later , there will be 4 chirp s and 4 flashe s . If a senso r is malfunctioning, you will receive the usual 2 chirps and ...

  • Clifford GP500 - page 17

    LED flashe s Meaning 1 flash Ig ni tion switch was turned on 2 flashe s Ac ti va tion of Digi tal Tilt/Mo tion Sen so r 3 flashe s Ac ti va tion of Dual- Level Piezo Sen so r 4 flashe s Ac ti va tion of hel met theft pre ven tion de vice 5 flashe s Op tional ad di tional trig ger was ac ti vated (such as a sea t trig ger) 6 flashe s Ac ti va tion o ...

  • Clifford GP500 - page 18

    Smart prior in tru sion at tempt aler t If you hear three chirps when you remotely disarm, it means that a trigger or sensor was activated in your absence. When you turn on the ignition (or start the engine), the LED will flash 1-8 times, pause, then repeat the flash cycle 4 more times. Count the number of flashes in one cycle and refer to the char ...

  • Clifford GP500 - page 19

    Smart Powe rUp™ 2 If power to the system is ever removed, SmartPowerUp 2 ensures that you r GP500 system automatically restores itself to its previous state when power i s restored. So if a thief disconnects the power and then restores it in a n attempt to start the motorcycle, the system will re-arm and instantly soun d the siren while immobilis ...

  • Clifford GP500 - page 20

    How to en ter your PIN Code for the first time The PIN code provides two functions: to turn the alarm off in the event tha t you cannot use your remote control and secondly, to access programmin g mode. Your GP500 PIN code was set by the factory. You may want t o change the PIN code using the instructions provided to insure the utmos t vehicle secu ...

  • Clifford GP500 - page 21

    2 . Within 5 seconds, press and release the Plain V iew 2 ✱ button 7 times. T o help you count, you will hear a chirp each time you press the ✱ button. After 7 presses, wait for a single chirp, then immediately enter your new PIN code . Example: To enter 4301 as your new code, you woul d press the switch buttons in this manner: ✱✱✱ ✱ bl ...

  • Clifford GP500 - page 22

    Step- by- step pro gram ming in struc tions 1. Refer to the T able of programmable features on page 32 and find the feature you wish to program. Make note of the number of times to press the ✱ button . 2 . T urn the ignition on, or start the engine (skip this step if the engine i s running). 3 . Enter your PIN code, then press and hold the ✱ bu ...

  • Clifford GP500 - page 23

    Ta ble of Pro gram ma ble Fea tures Featur e Factor y Settin g No. o f times to press the ✱ butto n Sec - ondar y Actio n Progra m completio n confirm - atio n Additiona l Actio n AutoArmin g OF F 2 - 1 chirp=OFF 2 chirps=O N - Chirps O N 3 - 1 chirp=ON 2 chirps=OF F - FACT ON 4 - 1 chirp=OFF 2 chirps=O N - Change PIN cod e See back cover o f thi ...

  • Clifford GP500 - page 24

    Featur e Factory Settin g No. o f times to press the ✱ butto n Sec - ondar y Actio n Progra m completion confirm - atio n Additiona l Actio n Pro gram othe r Clif ford ACG- 2 Re mote t o Arm/Dis arm GP500 - 1 0 Pres s re mot e con tro l but ton t o be as signe d to thi s func tio n 1 chirp = button i s ready to b e assigned t o the functio n Pres ...

  • Clifford GP500 - page 25

    Feature Factor y Setting No. o f times to press the ✱ butto n Sec - ondar y Actio n Progra m completio n confirm - atio n Additional Actio n Pro gram othe r Clif ford ACG- 2 Re mote to Ad jus t Piezo Sen sor for GP500 - 13 Pres s but ton t o be as signe d to thi s func tio n 4 chirps = button i s ready to b e assigned t o the function Pres s re m ...

  • Clifford GP500 - page 26

    2 4 GP50 0 ...

  • Clifford GP500 - page 27

    Your serial number is : REGISTER ONLINE: Within 10 days of purchase, yo u may register your Clifford purchase online at ww w .clifford.com/manuals so that we can contact you in the future if there are any changes or improvements to your GP500 system. Or just photocopy this page , note your name, address and vehicle make, model , year and VIN numbe ...

  • Clifford GP500 - page 28

    USA Head quar ters: Clif ford Elec tron ics, Inc. 20750 Las sen Street, Chatsworth, CA 91311 Within USA: 1- 800- 824- 3208 Phone: (818) 709- 7551 Fax: (818)407- 1743 All Clifford sys tems are cov ered b y one or more of the fol low ing Clif ford Elec tron ics US A pat ents : 4,158,874; 4,233,642; 4,327,444; 4,383,242; 4,430,685; 4,845,464; 4,887,06 ...

メーカー Clifford カテゴリー Bicycle Accessories

Clifford GP500のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- GP500の取扱説明書
- Cliffordの製品カード
- パンフレット
- またはClifford GP500の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Clifford GP500の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Clifford GP500の取り付け説明書、サービスマニュアル、簡易説明書、またはClifford GP500のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Clifford GP500の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Clifford GP500デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがClifford GP500を使用するのを助ける技術的文書のことです。説明書は通常、全てのClifford GP500ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cliffordの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Clifford GP500の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははClifford GP500の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Clifford GP500に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Clifford GP500デバイスの基本機能を使うにあたってのヒント。 Clifford GP500のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Clifford GP500に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるClifford GP500のメーカー/サービスへの連絡先に関する情報。

Clifford GP500についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもClifford GP500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがClifford GP500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)