Snapper CZT19481KWVの取扱説明書

40ページ 4.61 mb
ダウンロード

ページに移動 of 40

Summary
  • Snapper CZT19481KWV - page 1

    Safety Instructions & Operator's Manual for Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and p ay p articular attention to the "IMPORT ANT SAFETY INSTRUCTIONS" on Pages 2 - 4. Remember that all power equip- ment can be dangerous if used improperly . Also keep in mind that SAFET ...

  • Snapper CZT19481KWV - page 2

    2 ! ! IMPORT ANT SAFETY INSTRUCTIONS W ARNING: This powerful cutting machine is capable of amput ating hands and feet and can throw object s that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must underst and th ...

  • Snapper CZT19481KWV - page 3

    3 ! ! IMPORT ANT SAFETY INSTRUCTIONS PREP ARA TION (Continued From Previous Page) 3. Dat a indicates that operators age 60 and above, are involved in a large percent age of mower-related injuries. These operators should evaluate their ability to operate the mower safely enough to protect themselves and oth- ers from serious injury . 4. Handle fuel ...

  • Snapper CZT19481KWV - page 4

    4 ! ! IMPORT ANT SAFETY INSTRUCTIONS OPERA TION (Continued From Previous Page) 16. On slopes, the weight of the towed equipment may cause loss of traction and loss of control. When towing, travel slowly and allow extra dist ance to stop. 17 . DO NOT operate engine in enclosed areas. Engine exhaust gases cont ain carbon monoxide, a deadly poi- son. ...

  • Snapper CZT19481KWV - page 5

    5 T ABLE OF CONTENTS IMPORT ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4 T ABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 SECTION 1 - F AMILIARIZA TION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Snapper CZT19481KWV - page 6

    6 Section 1 - F AMILIARIZA TION IMPORT ANT The figures and illustrations in this manual are provided for reference only and may differ from your specific model. Cont act your Snapper dealer if you have questions. FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operators of the SNAPPER COMMERCIAL MID MOUNT ZERO TURNING HYDRO DRIVE. ...

  • Snapper CZT19481KWV - page 7

    7 Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROT A TING P ARTS KEEP A W A Y FROM MOVING P ARTS P ARKING BRAKE LEVER OPERA TION MOTION CONTROL LEVER OPERA TION WEAR HEARING PROTECTION W ARNING ! A VOID SERIOUS INJUR Y OR DEA TH ...

  • Snapper CZT19481KWV - page 8

    FUEL GAUGE (2) CONTROL P ANEL IDENTIFICA TION DANGER! ROT A TING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA FUEL T ANK SELECT IGNITION SWITCH STOP RUN ST ART 8 Section 2 - SAFETY MESSAGES AND SYMBOLS ...

  • Snapper CZT19481KWV - page 9

    9 Section 2 - SAFETY MESSAGES AND SYMBOLS ROLL BAR PROTECTIVE STRUCTURE DECALS ...

  • Snapper CZT19481KWV - page 10

    10 Section 3 - OPERA TING INSTRUCTIONS 3.1 PRE-ST ART CHECK LIST Make the following checks and perform the service required before each start-up. 3.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi. 3.1.2. Check guards, deflectors and covers to make sure al ...

  • Snapper CZT19481KWV - page 11

    11 Section 3 - OPERA TING INSTRUCTIONS Section 3 - OPERA TING INSTRUCTIONS ROLL RELEASE: T o roll the machine without the engine running, pressure within the hydraulic pump s must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure. Use a wrench to rot ate both relief valves co ...

  • Snapper CZT19481KWV - page 12

    12 Section 3 - OPERA TING INSTRUCTIONS Section 3 - OPERA TING INSTRUCTIONS 3.2.2. STOPPING ENGINE 1. S top engine by turning key to "ST OP" position. Move engine speed to the T urtle "SLOW" position and turn key to "STOP". See Figure 3.6. 3.2.3. ST ARTING MOWER BLADES 1. S t art engine and set engine speed control to t ...

  • Snapper CZT19481KWV - page 13

    13 Section 3 - OPERA TING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever . IMPORT ANT : There is a foot assist pedal located to the right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height. See Figure 3.10. 2. Inse ...

  • Snapper CZT19481KWV - page 14

    14 Section 3 - OPERA TING INSTRUCTIONS 3.4.2. STOPPING MACHINE 1. Return motion control levers to the neutral position & the neutral lock position. IMPORT ANT : Operator must use hand assistance to bring both motion control levers to the neutral position & the neutral lock position. 2. Engage parking brake. 3. Push Blade Switch down to the ...

  • Snapper CZT19481KWV - page 15

    15 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.1 INTRODUCTION T o retain the quality of the SNAPPER mower , use gen- uine SNAPPER replacement part s only . Contact a local SNAPPER dealer for part s and service assis- tance. For the correct p art or information for a particu- lar SNAPPER mower , always mention the model and serial ...

  • Snapper CZT19481KWV - page 16

    16 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BEL T 1. Lower deck to lowest setting. 2. Remove footrest. See Figure 4.3. 3. Removal of footrest will allow access to mower drive belt. 4. Check the belt tension. If belt is frayed, slit, sev- ered or belt strands exposed, replace belt before oper- ating mower ...

  • Snapper CZT19481KWV - page 17

    17 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.3.3. RIDING MOWER - LUBRICA TION 1. Front Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun. See Figure 4.5. 2. Hydro Pumps Check the level of the fluid in the fluid reservoir . Wipe away all dirt and debris from around reservoir cap befo ...

  • Snapper CZT19481KWV - page 18

    18 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.5 ANNUALL Y (END OF EACH SEASON) (Continued from previous Page) 4.5.2. FUEL FIL TER Service fuel filter as instructed below . T urn key to "OFF" position. Engine MUST be stopped and MUST be cold before removing filter . Clamp fuel line to pre- vent fuel spillage or perform f ...

  • Snapper CZT19481KWV - page 19

    19 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.6 DECK REMOV AL (Continued from previous p age) 4. Remove inside nuts that secure chain to front lift arm. See Figure 4.10. 5. Remove inside nuts that secure chain to rear lif t arm. See Figure 4.1 1. 6. Remove mower drive belt from around blade clutch pulley . Refer to Section “MOW ...

  • Snapper CZT19481KWV - page 20

    20 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.1 NEUTRAL POSITION ADJUSTMENTS The motion control levers control the movement and stopping of the machine. Move the control levers to the center or neutral position to stop machine. IMPORT ANT : Always return both motion control levers with hand assist ance to the neutra ...

  • Snapper CZT19481KWV - page 21

    21 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.1 NEUTRAL POSITION ADJUSTMENTS (Continued From Previous Page) 12. With motion control levers remaining in the neutral lock position, See Figure 3.7, hold connecting rod up to the activation assembly and check length of rod. T ie rod end bolt must align with the activatio ...

  • Snapper CZT19481KWV - page 22

    22 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.2.1. MOWER DECK ADJUSTMENT (LEVELNESS) SIDE to SIDE and FRONT to REAR 8. Move deck lift lever and set the mower deck to the highest cutting position and recheck side to side blade tip dimensions. The dif ference between the two should be 1/8" or less. NOTE: The deck ...

  • Snapper CZT19481KWV - page 23

    23 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.3 TRACTION BEL T TENSION The traction drive belt tension does not require adjustment. If the belt is slipping, it will have to be replaced. 5.4 TRACTION BEL T REPLACEMENT 1. Remove mower drive belt from around clutch pul- ley . See Figure 5.10. Refer to Section "MOW ...

  • Snapper CZT19481KWV - page 24

    24 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.6a MOTION LEVER HANDLEBAR ALIGNMENT Handlebars of both left and right Motion Control Levers should be aligned when levers are dropped from their neutral lock positions. See Figure 5.12a. If bars are not aligned: 1. Loosen bolts that secure handlebar adjustment brackets t ...

  • Snapper CZT19481KWV - page 25

    25 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.8 ENGINE ADJUSTMENTS & REP AIR Refer to the engine owner's manual for engine adjust- ments and/or rep airs. 5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS 1. Inspect blade frequently for signs of excessive wear or damage. Replace blade when it reaches the ...

  • Snapper CZT19481KWV - page 26

    26 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.10 BA TTER Y 5.10.1. BA TTER Y REMOV AL 1. Remove battery retainer . See Figure 5.17. 2. Slide terminal cover away from positive terminal. 3. Observe and note cable positions on battery . Disconnect cables from battery terminals, disconnect- ing BLACK (Negative) cable fi ...

  • Snapper CZT19481KWV - page 27

    27 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.10.4. BA TTER Y TESTING 1. Remove battery . Refer to Section "BA TTERY REMOV AL". 2. Using a voltmeter , check the battery's state of charge by comparing the voltmeter reading with the chart below . (Remember to hook the positive (red) lead of the voltmete ...

  • Snapper CZT19481KWV - page 28

    28 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.1 1 HYDRAULIC SYSTEM, PURGING After replacing or rep airing hydraulic system compo- nents, one or both of the wheel drives may not pull properly . This is likely to be caused by air entrapped in the system. If you experience a pulling issue after completing repairs, perf ...

  • Snapper CZT19481KWV - page 29

    29 Section 3 - OPERA TING INSTRUCTIONS TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION St arter Will Not Crank Engine 1. Battery dead. 1. Service battery . 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Clean and check connections for good contact. 4. Defective ignition switch. 4. Contact authorized SNAPPER ...

  • Snapper CZT19481KWV - page 30

    30 Section 3 - OPERA TING INSTRUCTIONS TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Machine Will Not Move Loss Of T raction 1. Motion Control Levers in the neutral "N" position. 1. Move Motion Controls to desired speed position. 2. Hydro. Pumps in roll release setting. 2. T ighten relief valves. 3. Low transmission hydraulic o ...

  • Snapper CZT19481KWV - page 31

    31 Section 3 - OPERA TING INSTRUCTIONS SER VICE SCHEDULE ITEM SERVICE PERFORMED REF . NUMBER EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 9 X Initial Oil Change Page 14 X Periodic Oil Change Page 15 X* Air Cleaner Clean or Replace Engine Manual X** Sp ark Plug Replace Engine Manual X Fuel Filter Replace Page 17 X ...

  • Snapper CZT19481KWV - page 32

    32 2 YEAR LIMITED W ARRANTY For two (2) years from purchase date for the original purchaser's use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any p art or part s found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both. ...

  • Snapper CZT19481KWV - page 33

    33 PRIMAR Y MAINTENANCE ...

  • Snapper CZT19481KWV - page 34

    34 PRIMAR Y MAINTENANCE ...

  • Snapper CZT19481KWV - page 35

    35 PRIMAR Y MAINTENANCE ...

  • Snapper CZT19481KWV - page 36

    36 PRIMAR Y MAINTENANCE ...

  • Snapper CZT19481KWV - page 37

    37 SNAPPER PRODUCT REGISTRA TION FORM IMPOR T ANT : KEEP THIS INFORMA TION FOR YOUR PERSONAL RECORDS (Complete the following information on your Snapper pur chase) Model Number_________________________________________________________ Serial Number _________________________________________________________ Date of Pur chase___________________________ ...

  • Snapper CZT19481KWV - page 38

    38 NOTES ...

  • Snapper CZT19481KWV - page 39

    39 NOTES ...

  • Snapper CZT19481KWV - page 40

    40 IMPORT ANT Snapper product s are built using engines that meet or exceed all applicable emissions requirement s on the date manufactured. The labels on those engines cont ain very import ant emissions information and critical safety warnings. Read, Underst and, and Follow all warnings and instructions in this manual, the engine manual, and on th ...

メーカー Snapper カテゴリー Lawn Mower

Snapper CZT19481KWVのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CZT19481KWVの取扱説明書
- Snapperの製品カード
- パンフレット
- またはSnapper CZT19481KWVの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Snapper CZT19481KWVの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Snapper CZT19481KWVの取り付け説明書、サービスマニュアル、簡易説明書、またはSnapper CZT19481KWVのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Snapper CZT19481KWVの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Snapper CZT19481KWVデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSnapper CZT19481KWVを使用するのを助ける技術的文書のことです。説明書は通常、全てのSnapper CZT19481KWVユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Snapperの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Snapper CZT19481KWVの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSnapper CZT19481KWVの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Snapper CZT19481KWVに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Snapper CZT19481KWVデバイスの基本機能を使うにあたってのヒント。 Snapper CZT19481KWVのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Snapper CZT19481KWVに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSnapper CZT19481KWVのメーカー/サービスへの連絡先に関する情報。

Snapper CZT19481KWVについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSnapper CZT19481KWVの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper CZT19481KWVで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)