Xantech PA1235の取扱説明書

16ページ 0.59 mb
ダウンロード

ページに移動 of 16

Summary
  • Xantech PA1235 - page 1

    ®  1 Amplifiers & Preamplifiers INST ALLA TION INSTRUCTIONS P A1235 2 CHANNEL POWER AMPLIFIER 123456 PA1235 12 CHANNEL POWER AMPLIFIER POWER GENERAL INFORMATION To enhance the ease of installation and obtain optimum performance from the PA1235, we recommend that you first become familiar with all its features and special capabilities by stu ...

  • Xantech PA1235 - page 2

    ®  2 • 12-11-10-9-8-7-6 Output Flexibility. Each of the 12 amplifiers can be driven singly or bridged to allow several channel and power output capabilities. It can be configured into seven power packages as follows: - Twelve 35-watt amplifiers - 12 total. - One 150 and ten 35-watt amplifiers - 11 total. - Two 150 and eight 35-watt amplifiers ...

  • Xantech PA1235 - page 3

    ®  3 Amplifiers & Preamplifiers In addition, this switch must be left in the MANUAL OFF (OUT) position to permit an external DC Control Voltage to power the PA1235 ON and OFF. Refer to " REMOTE MASTER ON/OFF CONTROL " terminals, item #13. NOTE: The PA1235 may also be powered ON/OFF with an external AC line switch into which the po ...

  • Xantech PA1235 - page 4

    ®  4 8. COMMON AUDIO BUS. A single audio source, such as from a connected preamp, can drive one or more of the amplifier pairs simultaneously, as desired, from this Bus. Any of the amplifier pairs can be switched to the COMMON AUDIO BUS at will by use of the COMMON BUS / LOCAL Switch (see also item #6). 9. LEVEL (System) RESET Button. Pressing ...

  • Xantech PA1235 - page 5

    ®  5 Amplifiers & Preamplifiers 12. SPEAKER Terminals. These plug-in 4-terminal screw type connectors permit speaker wire sizes up to 12 gauge. When making connections for the STEREO mode, be sure to observe the " + " and " – " polarity markings, just under the LEFT & RIGHT markings, for each wire pair going to the ...

  • Xantech PA1235 - page 6

    ®  6 • Since it includes adjustable code groups, the user may inadvertently alter the installer configurations. • Also, since the user will require IR commands from other brands of equipment to control the total system, in addition to those of the PA1235, all commands should be consolidated into one learning device, for ease of use. APPLICA ...

  • Xantech PA1235 - page 7

    ®  7 Amplifiers & Preamplifiers 7. MUTE ON / OFF . Separate ON / OFF Mute commands give positive mute action without knowing the actual mute status. This is very helpful in a remote room where commands are sent “ blind ” without any visual aids for status. NOTE : In addition to MUTE OFF, the muted condition can be released with VOLume ( ...

  • Xantech PA1235 - page 8

    ®  8 2. If mounted in an equipment cabinet or other confining location, allow at least 2 inches of space above the top cover (see Fig. 4 ). Be sure there are large openings in the shelf below the unit and in the cabinet to allow the entry of cool air and the escape of warm air. 3. If the cabinet contains other heat generating components or you ...

  • Xantech PA1235 - page 9

    ®  9 Amplifiers & Preamplifiers 6. As a rule of thumb, use 18 gauge speaker wire for speaker runs up to 30' (9m), 16 gauge up to 70' (21m), and 14 gauge up to 150' (39m). The 4-terminal connectors accept wire sizes up to 12 gauge max. 7. Strip the insulation back about 1/4" (6mm) and twist the strands on each lead to pre ...

  • Xantech PA1235 - page 10

    ®  10 NOTE: Only one speaker is connected per amplifier pair in the BRIDGED mode! CAUTION: When operating in the BRIDGED mode (particularly when bench testing the amplifier) do not make a ground or any other kind of connection to the amplifier speaker terminals other than those to the individual speakers as shown. Failures caused by inappropria ...

  • Xantech PA1235 - page 11

    ®  11 Amplifiers & Preamplifiers REMOTE MASTER ON/OFF CONTROL 5-30 VOLTS DC + -- N/C GROUND STA TUS IR IN COMMON AUDIO BUS AC LINE ON/OFF COMMON BUS LOCAL LEFT RIGHT STEREO MONO BRIDGED CI GROUND STA TUS IR IN LEFT RIGHT SPEAKER + -- -- + + BRIDGED -- 1 COMMON BUS LOCAL LEFT RIGHT STEREO MONO BRIDGED CI GROUND STA TUS IR IN LEFT RIGHT SPEAK ...

  • Xantech PA1235 - page 12

    ®  12 8. To keep the system cost low, no AC power management is included. The user would need to operate the power switching for each component individually, using front panel power switches, or IR, as appropriate. Individual room Standby ON/OFF is provided, however. The STATUS of Standby ON/OFF is indicated at the IR receivers and keypads via ...

  • Xantech PA1235 - page 13

    ®  13 Amplifiers & Preamplifiers REMOTE MASTER ON/OFF CONTROL 5-30 VOLTS DC + -- COMMON BUS LOCAL LEFT RIGHT STEREO MONO BRIDGED CI GROUND STA TUS IR IN LEFT RIGHT SPEAKER + -- -- + + BRIDGED -- 2 COMMON BUS LOCAL LEFT RIGHT STEREO MONO BRIDGED CI GROUND STA TAUS IR IN LEFT RIGHT SPEAKER + -- -- + + BRIDGED -- 3 CAUTION RISK OF ELECTRIC SHO ...

  • Xantech PA1235 - page 14

    ®  14 REMOTE MASTER ON/OFF CONTROL 5-30 VOLTS DC + -- N/C GROUND STA TUS IR IN COMMON AUDIO BUS AC LINE ON/OFF COMMON BUS LOCAL LEFT RIGHT STEREO MONO BRIDGED CI GROUND STA TUS IR IN LEFT RIGHT SPEAKER + -- -- + + BRIDGED -- 1 COMMON BUS LOCAL LEFT RIGHT STEREO MONO BRIDGED CI GROUND STA TUS IR IN LEFT RIGHT SPEAKER + -- -- + + BRIDGED -- 2 COM ...

  • Xantech PA1235 - page 15

    ®  15 Amplifiers & Preamplifiers TROUBLE SHOOTING If you encounter a problem, please review the items below. Be sure, in addition, to check other system components, such as preamplifiers, CD players, speakers, speaker wiring, etc., that may be at fault. 1. Front Panel LEDs do not light – no sound. • Check line cord for good contact in a ...

  • Xantech PA1235 - page 16

    ®  16 SPECIFICATIONS Number of Channels ............................................................................................................ .........................................12 Power Output Rated Continuous Power, Each Channel: ............................................. 8 Ohms .......................... 35 Watts All 12 channe ...

メーカー Xantech カテゴリー Stereo Amplifier

Xantech PA1235のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PA1235の取扱説明書
- Xantechの製品カード
- パンフレット
- またはXantech PA1235の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Xantech PA1235の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Xantech PA1235の取り付け説明書、サービスマニュアル、簡易説明書、またはXantech PA1235のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Xantech PA1235の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Xantech PA1235デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがXantech PA1235を使用するのを助ける技術的文書のことです。説明書は通常、全てのXantech PA1235ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Xantechの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Xantech PA1235の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははXantech PA1235の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Xantech PA1235に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Xantech PA1235デバイスの基本機能を使うにあたってのヒント。 Xantech PA1235のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Xantech PA1235に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるXantech PA1235のメーカー/サービスへの連絡先に関する情報。

Xantech PA1235についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもXantech PA1235の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがXantech PA1235で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)