日本語 dropdown-ico

Samsung SRP-350の取扱説明書

30ページ 2.07 mb
ダウンロード

ページに移動 of 30

Summary
  • Samsung SRP-350 - page 1

    Operator’s Manual All specifications are subjected to change without notice http://www.samsungminiprinters.com SRP-350 Ver.2 RECEIPT PRINTER 1 Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. Violating following instructions can cause serious injury ...

  • Samsung SRP-350 - page 2

    2 Violating following instructions can cause slight wound or damage the appliance. Keep the desiccant out of children’s reach. If not, they may eat it. Install the printer on the stable surface. If the printer falls down, it can be broken and you can hurt yourself. Use only approved accessories and do not try to disassemble, repair or remodel it ...

  • Samsung SRP-350 - page 3

    4 Table of Contents CHAPTER 1. SETTING UP THE PRINTER ..................................... 5 1-1. U NPACKING .............................................................................. 5 1-2. C ONNECTING THE C ABLES ............................................................. 6 1-3. C ONNECTING THE COMPUTER .................................... ...

  • Samsung SRP-350 - page 4

    6 1-2. Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector pa nel on the back of the printer, which is shown below : Notes : Before connecting any of the cables, make sure that both the printer and the host are turned off. 7 1-3. Connecting the computer You need an approp riate interface cable ...

  • Samsung SRP-350 - page 5

    8 1-5. Connecting the Power Supply CAUTIONS: When connecting or di sconnecting th e power supply from the pri nter, make sure th at the power supply is not plugged into an elec trical outlet . Otherwise you may damage the power supply or the printer. If the power supply’s rated voltag e and your outlet’s voltage do not match, contact your deale ...

  • Samsung SRP-350 - page 6

    10 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of pa per, as shown. Then close the cover. 7. Tear off the paper as shown. Notes : When closing the cover, press the center of printer cover firmly to prevent p a p er miss-loadin g 11 1-7. Adjustments and Settings The SRP-350 is set up at the ...

  • Samsung SRP-350 - page 7

    12 1-8. Using the Printer Control Panel Button The button can be disabl ed by the ESC c 5 command. Press the FEED button once to advance pap e r one line. You can also hold down the FEED button to feed paper continuously. Panel lights POWER The POWER light is on whenever the printer is on. ERROR This indicates an error. PAPER OUT This light indi ca ...

  • Samsung SRP-350 - page 8

    14 Parallel/USB Interface Specification Dip Switch Set 1 Functions SW FUNCTION ON OFF DEFAULT 1 Auto Line Feed Always Enabled Always Disabled OFF 2 Reserved - - OFF 3 Reserved - - OFF 4 Reserved - - OFF 5 Reserved - - OFF 6 Reserved - - OFF 7 Reserved - - OFF 8 Reserved - - OFF Dip Switch Set 2 Functions SW FUNCTION ON OFF DEFAULT 1 Emulation STAR ...

  • Samsung SRP-350 - page 9

    16 Chapter 3. The self test The self-test checks whether the printer has any problem s. If the printer does not function properly, contact your dealer. Th e self-test checks the following; 1. Make sure paper roll has been i nstalled properly . 2. Turn on the power while holdin g down the FEED button. The s elf-test begins . 3. The self-test prints ...

  • Samsung SRP-350 - page 10

    18 Page 2 ( PC850 : Multilingual ) 19 Page 3 ( PC860 : Portuguese ) ...

  • Samsung SRP-350 - page 11

    20 Page 4 ( PC 863 : Canadian - French ) 21 Page 5 ( PC 865 : Nordic ) ...

  • Samsung SRP-350 - page 12

    22 Page 19 ( PC 858 : Euro ) 23 Page 255 ( Space Page ) ...

  • Samsung SRP-350 - page 13

    24 International Character Set 25 Chapter 5. Control Commands List C o n t r o l c o d e s Hexadecimal C o d e s Function <HT> 09 Horizontal tab <LF> 0A Print and line feed <FF> 0 C Print and return to standard mode in page mode <CR> 0D Print and carriage return <CAN> 18 Cancel print data in pa ge mode <DLE> < ...

  • Samsung SRP-350 - page 14

    26 Control codes Hexadecimal c o d e s Function <ESC> c 3 n 1B 63 33 n Select paper sensor to output pap er end signals <ESC> c 4 n 1B 63 34 n Select paper sensor to stop p rinting <ESC> c 5 n 1B 63 35 n Enable/Disab le panel butto n <ESC> d n 1B 64 n Print and feed n lines <ESC> p m t1 t2 1 B 70 m t1 t2 Generate pulse ...

  • Samsung SRP-350 - page 15

    28 CAN [Name] [Format] [Description] Cancel print data i n page mode. ASCII CAN H e x 1 8 Decimal 24 In page mode, deletes all the print data in the current printabl e area. DLE EOT n [Name] [Format] [Range] [Description] Real-time status transmission. A S C I I D L E E O T n H e x 1 0 0 4 n D e c i m a l 1 6 4 n 1 ≤ n ≤ 4 Transmits the selecte ...

  • Samsung SRP-350 - page 16

    30 ESC FF [Name] [Format] [Description] Print data i n page mode. A S C I I E S C F F H e x 1 B 0 C D e c i m a l 2 7 1 2 In page mode, prints all buffered data in th e printing area coll ectively. ESC SP n [Name] [Format] [Range] [Description] Set right-side character spacing. A S C I I E S C S P n H e x 1 B 2 0 n D e c i m a l 2 7 3 2 n 0 ≤ n ? ...

  • Samsung SRP-350 - page 17

    32 ESC * m nL nH d1…dk [Name] [Format] [Range] [Description] Select bit-i mage mode. A S C I I E S C * m n L n H d 1 … d k H e x 1 B 2 A m n L n H d 1 … d k D e c i m a l 2 7 4 2 m n L n H d 1 … d k m = 0, 1, 32, 33 0 ≤ nL ≤ 255 0 ≤ nH ≤ 3 0 ≤ d ≤ 255 Selects a bit- image mode using m for th e number of dots specif ied by nL and ...

  • Samsung SRP-350 - page 18

    34 ESC D n1… nk NUL [Name] [Format] [Range] [Description] Set horizontal tab positions. A S C I I E S C D n 1 … n k N U L H e x 1 B 4 4 n 1 … n k 0 0 D e c i m a l 2 7 6 8 n 1 … n k 0 1 ≤ n ≤ 255 0 ≤ k ≤ 32 Sets horizontal tab positions. * n specifies the column number for setting a horizontal tab position from the beginning of the ...

  • Samsung SRP-350 - page 19

    36 ESC T n [Name] [Format] [Range] [Description] [Default] Select print di rection in page mode. A S C I I E S C T n H e x 1 B 5 4 n D e c i m a l 2 7 8 4 n 0 ≤ n ≤ 3 48 ≤ n ≤ 51 Selects the pri nt direction and s tarting posit ion in page mode. n specifies the print direction and starting p osition as follows : n Print Direction Starting P ...

  • Samsung SRP-350 - page 20

    38 ESC c 4 n [Name] [Format] [Range] [Description] Select paper sensor(s) to stop printing. A S C I I E S C c 4 n H e x 1 B 6 3 3 4 n D e c i m a l 2 7 9 9 5 2 n 0 ≤ nL ≤ 255 Selects the paper sens or(s) used to stop prin ting when a paper-end is detected, using n as follows : Bit Off/On Hex Decimal Function Off 00 0 Paper roll end sensor disab ...

  • Samsung SRP-350 - page 21

    40 FS q n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk]n [Name] [Format] [Range] [Description] Defined NV bit i mage. A S C I I F S q n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk]n H e x 1 C 7 1 n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk]n Decimal 28 113 n [xL xH yL yH d1…dk]1…[xL xH yL yH d1…dk]n 1 ≤ n ≤ 255 0 ≤ xL ≤ 255 0 ? ...

  • Samsung SRP-350 - page 22

    42 GS B n [Name] [Format] [Range] [Description] Turn white/black reverse pri nting mode on/off. A S C I I G S B n H e x 1 D 4 2 n D e c i m a l 2 9 6 6 n 0 ≤ n ≤ 255 Turns on or off whit e/black reverse print ing mode. * When the LSB is 0, white/black re verse pri nting mode is turned o ff. * When the LSB is 1, white/black re verse pri nting mo ...

  • Samsung SRP-350 - page 23

    44 GS W nL nH [Name] [Format] [Range] [Description] Set printing area width. A S C I I G S W n L n H H e x 1 D 5 7 n L n H D e c i m a l 2 9 8 7 n L n H 0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255 Sets the printing area width to the area specified by nL and nH. * The printing area width is set to [ ( n L + n H × 256) × horizontal motion unit] inches. GS ? ...

  • Samsung SRP-350 - page 24

    46 First byte (printer information) Bit Off/On Hex Decimal Status for ASB 0 Off 00 0 Not used. Fixed to Off. 1 Off 00 0 Not used. Fixed to Off. Off 00 0 Drawer kick-out connector pin 3 is LOW. 2 On 04 4 Drawer kick-out connector pin 3 is HIGH. Off 00 0 Onl ine. 3 On 08 8 Offline. 4 On 10 16 Not used. Fixed to On. Off 00 0 Cover is closed. 5 On 20 3 ...

  • Samsung SRP-350 - page 25

    48 ① GS k m d1…dk NUL , ② GS k m n d1…dn [Name] [Format] [Range] [Description] Print bar code. ① A S C I I G S k m d 1 … d k N U L H e x 1 D 6 B m d 1 … d k 0 0 Decimal 29 107 m d1…dk 0 ② A S C I I G S k m n d 1 … d n H e x 1 D 6 B m n d 1 … d n Decimal 29 107 m n d1…dn ① 0 ≤ m ≤ 6 (k and d depends on the bar code syst ...

  • Samsung SRP-350 - page 26

    50 APPENDIX A. Star Mode Command Summary Control codes Hexadecimal codes Function <ESC> ”R” n 1B 52 n Select international character set <ESC> <GS> t n 1B 1D 74n Select character table <ESC> ”/” “1” <ESC> ”/” <1> 1B 2F 31 1B 2F 01 Select slash zero <ESC> ”/” “0” <ESC> ”/” & ...

  • Samsung SRP-350 - page 27

    52 Control codes Hexadecimal codes Function <FS> 1C Co ntrol peripheral device #1 immediately. <EM> 19 Control peripheral device #2 immediately <SUB> 1A Co ntrol peripheral device #2 immediately <ESC> “d” n 1B 64 n Partial-cut com mand to the auto cutter. <CAN> 18 Cancel last line & Initialize printer immediate ...

  • Samsung SRP-350 - page 28

    54 RS-232C Cable Connection RS-485 Cable Connection 55 Interface Connector Serial Interface (RS-232) Pin No. Signal name Direction Function 1 FG - Frame Ground 2 TxD Output Transmit Data 3 RxD Input Receive Data 4 RTS Output Ready To Send 5 CTS Input Clear To Send 6 DSR Input Data Set Ready 7 SG - Signal Ground 20 DTR Output Data Terminal Ready Ser ...

  • Samsung SRP-350 - page 29

    56 Parallel Interface (IEEE-1284) Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk HostClk 2 Host / Printer Data 0 (LSB) - Data 0 (LSB) 3 Host / Printer Data 1 - Data 1 4 Host / Printer Data 2 - Data 2 5 Host / Printer Data 3 - Data 3 6 Host / Printer Data 4 - Data 4 7 Host / Printer Data 5 - Data 5 8 Host / Printer Da ...

  • Samsung SRP-350 - page 30

    58 D. Specification Printing method Thermal line printing Dot density 180 X 180 dpi (7dots/mm) Printing width 72.192 ± 0.2mm Paper width 79 ~ 80 mm Characters per line (default) 42 (Font A) 56 (Font B) Printing speed 35.5 lines/sec(1/6” Feed) 150 mm/sec Receive Buffer Size 4K Bytes NOTE : Printing speed may be slower, depending on the data trans ...

メーカー Samsung カテゴリー Printer

Samsung SRP-350のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SRP-350の取扱説明書
- Samsungの製品カード
- パンフレット
- またはSamsung SRP-350の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Samsung SRP-350の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Samsung SRP-350の取り付け説明書、サービスマニュアル、簡易説明書、またはSamsung SRP-350のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Samsung SRP-350の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Samsung SRP-350デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSamsung SRP-350を使用するのを助ける技術的文書のことです。説明書は通常、全てのSamsung SRP-350ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Samsungの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Samsung SRP-350の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSamsung SRP-350の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Samsung SRP-350に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Samsung SRP-350デバイスの基本機能を使うにあたってのヒント。 Samsung SRP-350のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Samsung SRP-350に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSamsung SRP-350のメーカー/サービスへの連絡先に関する情報。

Samsung SRP-350についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもSamsung SRP-350の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSamsung SRP-350で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)