Huffy 211376Aの取扱説明書

18ページ 0.55 mb
ダウンロード

ページに移動 of 18

Summary
  • Huffy 211376A - page 1

    1 05/03 P/N 211376A Customer Service N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. A Huffy Comp any WRITE IN YOUR MODEL NUMBER: __________ REQUIRED TOOLS AND MA TERIALS: • Two People • Tape Measure • Tape • Shovel and Spade • Concrete, 900 lb. (408 kg) and Container to Mix • Carpenter’s Level • Wood Board (Scrap) • Ste ...

  • Huffy 211376A - page 2

    2 P/N 211376A 05/03 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolt s into large holes of elevator tubes, backboard bracket s and triangle plates. Carefully rock them in a circular motion to ream out any excess p aint from ho ...

  • Huffy 211376A - page 3

    05/03 P/N 211376A 3 F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, suppor t braces or net. • During play , especially when performin ...

  • Huffy 211376A - page 4

    4 P/N 211376A 05/03 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONTO P AGE 1 OF THIS OWNERS MANUAL 1. Make sure ground is level with playing surface, then dig pole hole. 2. CONTACT UTILITIES BEFORE DIGGING. W ARNING! Correctly identify each pole section and mark indicated distance from ends with tape. BOTTOM MIDDLE 3 5-1/2” (14 cm) TOP 5-1/2” (14 c ...

  • Huffy 211376A - page 5

    05/03 P/N 211376A 5 5. Fill hole approximately 3/4 full with concrete. Tamp down concrete to release air pockets. PLAYING SURFACE Insert bottom pole section (3) into ground sleeve (4). 3. 4. Assemble clamps (7) around bottom pole and ground sleeve (4) as shown. 5 5 8 8 7 4 7 6 6 IMPORT ANT! CLAMP ASSEMBLY MUST BE POSITIONED AS SHOWN BELOW. 7 4 3 ...

  • Huffy 211376A - page 6

    6 P/N 211376A 05/03 6. Insert ground sleeve (4) and pole section (3) into hole. Fill remaining hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Center and level ground sleeve assembly in hole. Check leveling on all sides several times while concrete is curing. NOTE: Make sure concrete is set up to clamp assembl ...

  • Huffy 211376A - page 7

    05/03 P/N 211376A 7 C O N C R E T E 1" (2.54cm) IMPORT ANT! Bounce pole top (1) and middle section (2) together as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 4-1/2" (11.4 cm) minimum overlap. IMPORT ANT! Add bottom pole section (3) to assembly. Bounce pole sections together 3 times, rota ...

  • Huffy 211376A - page 8

    8 P/N 211376A 05/03 14. Lower clamp cover (12) over clamps and snap into proper position. 13. Secure clamps (7) around pole section as shown. Refer to Step 4. Tighten completely. 12. 11 12 12 3 12 IMPORT ANT! ELEVATOR HOLES MUST BE PARALLEL WITH PLAYING SURFACE. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT ...

  • Huffy 211376A - page 9

    05/03 P/N 211376A 9 F R O N T 17 14 19 13 18 16 14 15 15 18 14 15. Beginning with top hole in left and right screw jack support plates (16 & 17), install elevator tubes (15) to pole as shown. Then secure lower holes in support plates to pole. NOTE: Not all holes in support plates (16 & 17) are used in this assembly. IMPORT ANT! DO NOT OVER ...

  • Huffy 211376A - page 10

    10 P/N 211376A 05/03 1 7 9 8 11 7' 2.1m 20 22 21 24 24 IMPORT ANT! DO NOT OVER TIGHTEN. 23 POLE 14 18 18 21 15 15 16 17 14 17. 18. Center screw jack (21) between support plates (16 & 17) and secure as shown below. Attach logo label (22) to height indicator cover (23). Place cover (23) over screw jack (21). Install pole cap (11). 16. Attach ...

  • Huffy 211376A - page 11

    05/03 P/N 211376A 11 ½ 13 14 18 14 15 15 26 26 Secure upper elevator tubes (15) to pole assembly as shown. 19. Insert spacer (25) through top holes of height indicator cover (23) and screw jack assembly as shown. Align spacer (25) and screw jack assembly between elevator tubes (15) and secure. 20. IMPORT ANT! WHEN SECURING SCREW JACK (21) TO TOP E ...

  • Huffy 211376A - page 12

    12 P/N 211376A 05/03 7' 2.1m 18 14 30 30 14 30 30 14 18 18 18 14 14 14 27 15 15 15 15 28 28 22. NOTE: Two people recommended for this operation. Attach Y-frame support bracket (27) to elevator tubes (15) as shown. NOTE: Same hardware used for upper and lower installation. 21. Loosely assemble bolt (28) and nut (29) to Y-frame support bracket ( ...

  • Huffy 211376A - page 13

    05/03 P/N 211376A 13 ½ 29 28 27 23. Lift backboard upright and insert bolt (28) heads into key slots. Slide backboard downward to position bolt (28) into channel as shown. Align rim mounting holes on Y-frame support bracket (27) to rim holes on backboard and tighten completely. IMPORT ANT! ALIGN RIM MOUNTING HOLES WITH HOLES IN Y- FRAME TWO PERSON ...

  • Huffy 211376A - page 14

    14 P/N 211376A 05/03 24. 25. ½ 33 31 29 Attach rim (33). Note: Mounting nuts (29) and bolts (31) supplied with rim hardware. USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. Install net clips (34). WARNING The Quick Clip™ rapid ...

  • Huffy 211376A - page 15

    05/03 P/N 211376A 15 Position looped end of height adjustment crank (36) onto hook as shown. Rotate crank handle to raise or lower backboard. View label (20) to determine approximate backboard height. 27. 26. Height Adjustment HOOK 36 20 STORE CRANK OUT OF REACH OF CHILDREN. DO NOT ALLOW CHILDREN TO ADJUST HEIGHT WITHOUT ADULT SUPERVISION COULD RES ...

  • Huffy 211376A - page 16

    16 P/N 211376A 05/03 H U FFY HUFFY SP ORTS 10 feet (3.05 m) 37 REGULATION RIM HEIGHT IS 10 FEET (3.05 M). 28. Apply height adjustment label (37) to front of pole as shown. Secure pole pad (32) as shown. 29. 32 ...

  • Huffy 211376A - page 17

    05/03 P/N 211376A 17 P ARTS LIST HARDW ARE IDENTIFIER * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item Qty. Part No. Description 1 1 900757 Top Pole Section 2 1 900874 Middle Pole Section, Flared End 3 1 908215 Bottom Pole Section 4 1 206500 Ground Sleeve, Square 5 2 201124 Lock Nut, Hex Head, 3/8 x 16 6 4 203232 Washer, Flat, 3/8 x 3/4 O.D. 7 2 20 ...

  • Huffy 211376A - page 18

    18 P/N 211376A 05/03 HARDW ARE IDENTIFIER (CONTINUED) * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item #25 (1) Item #29 (6) Item #30 (4) Item #31 (4) Item #34 (12*) Item #28 (2) Item #26 (2) Item #24 (2) ...

メーカー Huffy カテゴリー Fitness Equipment

Huffy 211376Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 211376Aの取扱説明書
- Huffyの製品カード
- パンフレット
- またはHuffy 211376Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Huffy 211376Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Huffy 211376Aの取り付け説明書、サービスマニュアル、簡易説明書、またはHuffy 211376Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Huffy 211376Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Huffy 211376Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHuffy 211376Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのHuffy 211376Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Huffyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Huffy 211376Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHuffy 211376Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Huffy 211376Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Huffy 211376Aデバイスの基本機能を使うにあたってのヒント。 Huffy 211376Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Huffy 211376Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHuffy 211376Aのメーカー/サービスへの連絡先に関する情報。

Huffy 211376Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHuffy 211376Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHuffy 211376Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)