Panasonic Digital Cordless Telephone Systemの取扱説明書

29ページ 0.21 mb
ダウンロード

ページに移動 of 29

Summary
  • Panasonic Digital Cordless Telephone System - page 1

    Panasonic DECT Digital Cordless T elephone System Operating Instructions Before operating this system, please read these instructions completely . THIS EQUIPMENT IS NOT DESIGNED FOR MAKING EMERGENCY TELEPHONY CALLS WHEN THE POWER F AILS. AL TERNA TIVE ARRANGEMENTS SHOULD BE MADE FOR ACCESS T O EMERGENCY SER VICES. ...

  • Panasonic Digital Cordless Telephone System - page 2

    1 CONTENTS CHAPTER 1. Introduction .............................................................. 3 1. Overview ........................................................................... 3 2. Safety Information ............................................................ 4 CHAPTER 2. Getting Started ................................................ ...

  • Panasonic Digital Cordless Telephone System - page 3

    3. Recall (Send earth recall or timed break signal to PBX) ............................................................................ 20 4. Changing fr om Pulse to T one ........................................ 21 5. An y Ke y Answer ............................................................. 21 6. Checking the Charge counter .................. ...

  • Panasonic Digital Cordless Telephone System - page 4

    3 Introduction IMPORTANT NOTICE FOR U.K . 1) Please ensure that the apparatus is not connected in parallel to any other equipment that is intended for connection to the PSTN. 2) Although Radio Exchange can use either loop disconnect or DTMF signalling. Only the performance of the DTMF signalling is subject to regulatory requirements for correct ope ...

  • Panasonic Digital Cordless Telephone System - page 5

    4 2. Safety Information This equipment is intended for use when supplied with power from the charger through the AC Adaptor. Other usage will invalidate any approval given to this apparatus and may be dangerous. Switch off your DECT telephone when in an aircraft. The use of telephones in an aircraft may be dangerous to the operation of the aircraft ...

  • Panasonic Digital Cordless Telephone System - page 6

    5 Getting Started This chapter describes preparations and other items you must be aware of before starting operation. Prepare your PS for use as follows: • Install the battery pack. • Charge your PS. These preparations are described in detail below. 1. Installing the battery pack The PS is operated by voltage supplied from the battery pack. Fol ...

  • Panasonic Digital Cordless Telephone System - page 7

    6 Getting Started (4) Slide the battery cover in the direction of the arrow until you hear it click into position. 2. Charging the PS (1) Plug the AC adaptor into the charger. (2) Plug the AC adaptor into a power outlet. Power Outlet ...

  • Panasonic Digital Cordless Telephone System - page 8

    7 (3) Place the PS with its battery pack in the charger. The charge lamp on the charger lights. While the PS is placed on. Notes: • The first time you charge your battery pack, charge it for more than 15 hours. • If you replace the battery pack, or it has not been used for a long time, or if it goes flat while you are using the PS, charge the b ...

  • Panasonic Digital Cordless Telephone System - page 9

    8 3. T urning the power ON/OFF 3.1 T urning the power ON When the power is turned ON, the PS can be operated. 1. Hold the [Power] key down for at least one second. All icons are displayed on the display for about one second. Then, the display changes as follows depending on the state of the PS. Getting Started 3.2 T urning the power OFF When the po ...

  • Panasonic Digital Cordless Telephone System - page 10

    9 Press the [volume( ▲ )] key or [volume( ▼ )] key while the PS is standing by or while it is ringing. Pressing the [volume( ▲ )] key increases the volume, and pressing the [volume( ▼ )] key decreases the volume. 4.2 Adjusting the v olume of con versations The volume of conversations can be adjusted in three stages (Low → Middle1 → Midd ...

  • Panasonic Digital Cordless Telephone System - page 11

    10 Getting Started 1. Press the [Programming] key. The PS enters the Programming mode. 2. Press the [2] dial key. 3. Set the tone pattern. To set the tone pattern 1: Press the [1] dial key. To set the tone pattern 2: Press the [2] dial key. To set the tone pattern 3: Press the [3] dial key. Note: • To cancel setting midway, press the [On-hook] ke ...

  • Panasonic Digital Cordless Telephone System - page 12

    11 1 : Incoming call indicato r Blinks when an incoming call arrives. 2 : [Speed dial] key Press to store speed dial or make a speed dial call. 3 : [Programming] key Press to enter the Programming mode. Also, press during storing. 4 : [F] key This key is used to change the ID of the PS for accessing another system. Up to 4 ID’s can be stored. Not ...

  • Panasonic Digital Cordless Telephone System - page 13

    12 Names And Functions 1 2 3 2. Display 2.1 1st line 1 : Off-Hook icon This icon is displayed when you press the [Off-hook] and [Intercom] keys to call an external line or intercom. It is also displayed blinking when you press the [Hold] key to put the conversation on hold. It disappears when you press the [On-hook] key to terminate the conversatio ...

  • Panasonic Digital Cordless Telephone System - page 14

    13 1. Making an Exchange Line Call 1.1 Making a call after hearing the outside dial tone The telephone No. is sent after an exchange line has been secured. An outside call can be placed with a minimum number of operations. 1. Press the [Off-hook] key. Listen for an outside dial tone. 2. Enter the telephone No. The number appears on the display. Not ...

  • Panasonic Digital Cordless Telephone System - page 15

    14 4. Press the [On-hook] key to terminate the call. 2. Making an Internal Call 2.1 Making a call after hearing the Intercom dial tone 1. Press the [INT] key. Listen for the Intercom dial tone of the host PBX. 2. Enter the extension No. The number appears on the display. Note: • If you make a mistake entering the extension No., press the [no-hook ...

  • Panasonic Digital Cordless Telephone System - page 16

    15 Basic Operation HOLD HOLD 3. Receiving Calls When the PS rings, press [Off-hook] key to answer. 1. When the PS rings, press the [Off-hook] key. The Incoming call indicator lamp blinks (or lights continuously). When you set Any Key Answer, you can reply by pressing any key other than the [Power] Key. (Refer to Chapter 5.) 2. Start your conversati ...

  • Panasonic Digital Cordless Telephone System - page 17

    16 APPLIED OPERA TION 1. Speed Dial You can store frequently-dialled outside or internal Nos. under speed dialling Nos. for quick calling. 1.1 Storing/Checking Speed Dialling Nos. You can store up to 10 speed dialling Nos., each consisting of up to 32 digits. Reference: • You can store speed dialling Nos. even when out of range or while making an ...

  • Panasonic Digital Cordless Telephone System - page 18

    17 Applied Operation 4. Press the [Programming] key. This exits memory mode. • To store another telephone No. before pressing [programming] key, repeat steps 2 to 4. • The completion tone sounds when you finish storing a speed dial No. HOLD 1.2 Changing and Deleting Speed Dialling Nos. 1. Press the [Programming] key while the PS is not being us ...

  • Panasonic Digital Cordless Telephone System - page 19

    18 Applied Operation 5. Press the [Programming] key. This exits memory mode. • To change or delete another telephone No. before pressing the [Programming] key, repeat steps 2 to 4. 1.3 Making a call using a speed dial No. 1.3.1 Making a call after hearing the dial tone 1. Press the [Off-hook] key. Listen for dial tone. 2. Press the [Speed dial] k ...

  • Panasonic Digital Cordless Telephone System - page 20

    19 Applied Operation 4. Wait for the called party to answer the PS, then start your conversation. 5. Press the [On-hook] key to terminate the call. 2. Redial 2.1 Last Number Redial You can redial the last number that you called. Reference: • The last-called number is lost when you turn off the power. • Your PS stores telephone Nos. of up to 32 ...

  • Panasonic Digital Cordless Telephone System - page 21

    20 Applied Operation 2. You can also press the [Volume] keys ( ▲ and ▼ ) to select the telephone No. to redial. Pressing the [Volume] keys successively displays each of the telephone Nos. in the reverse order in which they were dialled. If you want to modify a telephone No. before dialling it, press [HOLD] key to delete the No., then enter the ...

  • Panasonic Digital Cordless Telephone System - page 22

    21 Applied Operation 4. Changing fr om Pulse to T one [Pr ogramming required] To change from dial pulse to tone signals during a call or while you are dialling is possible even if the exchange line you are using is pulse signalling. 1. Press the [Programming] key. 2. Press the [Asterisk] key. 3. Press the [Programming] key. 5. An y Ke y Answer [Pr ...

  • Panasonic Digital Cordless Telephone System - page 23

    22 6. Checking the Charge Counter You can check the battery charged level on the display. The charged level is displayed in 10 stages. 1. Press the [On-Hook] key during standby. Note: • The charged level counter is inaccurate. The Low Voltage Icon may be displayed to inform the operator of low battery level even if the charged level counter is st ...

  • Panasonic Digital Cordless Telephone System - page 24

    23 ALARM FUNCTION 1. Err or Alarm Function When you turn the power ON, the PS carries out self-diagnostics to check for any hardware errors. If an error is found, an error number is displayed accompanied by an alarm to inform the operator. The following three error numbers are displayed to indicate the error type: Display Indication PS Status A fat ...

  • Panasonic Digital Cordless Telephone System - page 25

    24 Subscription Registration 1. Subscription Registration The PS can store IDs for use with up to 4 RE. Authentication Code (AC) are required for each system. 1. Press the [Power] key while pressing and holding the [Intercom] and [#] keys to select PS registra- tion mode. Note: • The mode Nos. are displayed. Nos. in use blink. Nos. not in use lig ...

  • Panasonic Digital Cordless Telephone System - page 26

    25 2. PS-ID display 1. Press the [Power] key while pressing and holding the [Intercom] and [#] keys to select CS registra- tion mode. Note: • The mode Nos. are displayed. Nos. in use blink. Nos. not in use light continuously. 2. Select a registration No. 3. Press the [Redial] key to display the PS-ID (IPUI-N). Note: Be sure to note down this ID a ...

  • Panasonic Digital Cordless Telephone System - page 27

    26 Other Information 1. Care and Maintenance • Pressing any of the keys may produce a loud tone. Avoid holding the telephone close to the ear while pressing the keys. • Extreme temperatures may have a temporary effect on the operation of your telephone. This is normal and does not indicate a fault. • Do not disassemble the equipment. There ar ...

  • Panasonic Digital Cordless Telephone System - page 28

    27 2. T r ouble Shooting Should any problem persist contact your dealer. Other Information Problem Telephone will not switch on Short battery life Calls cannot be made Calls cannot be made from Fixed Dial Memory Calls cannot be received Causes and Solutions Check that the battery pack is fully charged and correctly connected to the telephone. Batte ...

  • Panasonic Digital Cordless Telephone System - page 29

    7L1028AZAJ ...

メーカー Panasonic カテゴリー Telephone

Panasonic Digital Cordless Telephone Systemのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Digital Cordless Telephone Systemの取扱説明書
- Panasonicの製品カード
- パンフレット
- またはPanasonic Digital Cordless Telephone Systemの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Panasonic Digital Cordless Telephone Systemの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Panasonic Digital Cordless Telephone Systemの取り付け説明書、サービスマニュアル、簡易説明書、またはPanasonic Digital Cordless Telephone Systemのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Panasonic Digital Cordless Telephone Systemの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Panasonic Digital Cordless Telephone Systemデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPanasonic Digital Cordless Telephone Systemを使用するのを助ける技術的文書のことです。説明書は通常、全てのPanasonic Digital Cordless Telephone Systemユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Panasonicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Panasonic Digital Cordless Telephone Systemの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPanasonic Digital Cordless Telephone Systemの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Panasonic Digital Cordless Telephone Systemに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Panasonic Digital Cordless Telephone Systemデバイスの基本機能を使うにあたってのヒント。 Panasonic Digital Cordless Telephone Systemのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Panasonic Digital Cordless Telephone Systemに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPanasonic Digital Cordless Telephone Systemのメーカー/サービスへの連絡先に関する情報。

Panasonic Digital Cordless Telephone Systemについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPanasonic Digital Cordless Telephone Systemの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPanasonic Digital Cordless Telephone Systemで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)