Pfaff hobbymatic 800の取扱説明書

25ページ 関係なし
ダウンロード

ページに移動 of 25

Summary
  • Pfaff hobbymatic 800 - page 1

    Hobbymatic A 800., 801, 802, 803, 806, 807 instruction book ...

  • Pfaff hobbymatic 800 - page 2

    4 ________________________I Fold out this page Contents Page Removing the carrying case cover 1 Foot control receptacle 1 Electrical connection 2 Foot control 2 Disengaging motor 3 Removing bobbin case and bobbin 3 Disengaging the sewing mechanism 4 Bobbin winding 4 Inserting the bobbin 5 Inserting the bobbin case 5 Upper threading 6 Threadingthene ...

  • Pfaff hobbymatic 800 - page 3

    4 C, Cl - — C, 0) -.J 0) c5OD ...

  • Pfaff hobbymatic 800 - page 4

    4 Parts of your sewing machine 1 Take-up lever 2 Thread guide 3 Bobbin tension stud (for bobbin winding) and thread guiding hook 4 Zigzag-stitch lever 5 Utility- and stretch-stitch selector dial (802-807) 6 Buttonhole and needle positioning lever 7 Spool pins 8 Bobbin winder 9 Hand wheel 10 Stop motion knob 11 Stitch length control 12 Reverse feed ...

  • Pfaff hobbymatic 800 - page 5

    Removing the carrying case cover Open the hinges on both sides of the cover (G), move them back up (H) and then remove the cover (I). To replace the cover, reverse this proce dure, making sure the bottom of the hinge catches properly in the slot. Foot control receptacle Remove this receptacle from the machine for sewing. Before putting the machine ...

  • Pfaff hobbymatic 800 - page 6

    Electrical connection Push plug G into the machine socket and plug H into the wall socket. Your machine is now ready for sewing. Foot control Place the foot control on the floor under the table. Press it down with your foot. The machine starts sewing. The more you press down the pedal, the faster the machine runs. 2 ...

  • Pfaff hobbymatic 800 - page 7

    3 CD DC 2. 3 ZT :3 : CD = ‘< D CO 9. DC U) 03 ?C 0 ’ 0 a DC rCD 0 - CD CC) D CD 0 U) :3 OCDNQ Cflj CD =OU):3CD —. U) .I?i1 I Ca COQ a a. C CD U) —— 0. :3 a 0 D C D CD CD Cl) 3 Q:3’ 00 CD - — a- CD CD a a- CD a- (0 0 0. a a-DC CD 0 a • - - r3 U) ( o CD • <0) U) CD Z — (U a a Z) 0 2: PC 0 - 3 o cii ...

  • Pfaff hobbymatic 800 - page 8

    Disengaging the sewing mechanism Before you start winding the bobbin, disengage the sewing mechanism. To do this, hold the hand wheel steady and with the other hand turn the stop motion knob towards you. After bobbin winding, turn the knob in the opposite direction to re-engage the sewing mechanism. 4 Bobbin winding Disengage the sewing mechanism. ...

  • Pfaff hobbymatic 800 - page 9

    Inserting the bobbin case Pull up latch I and push the bobbin case onto stud B as far as it will go. Cutout H must point upwards. Release the latch. Stud G and latch I must be flush. Inserting the bobbin Insert the filled bobbin in the bobbin case so that the thread unreels towards the back (G). Then draw the thread into slot H and under the spring ...

  • Pfaff hobbymatic 800 - page 10

    Upper threading Raise the sewing foot and the take-up lever. Pull the thread from the spool through thread guiding hook 3, thread guide 2 and from the right into needle thread tension 19. Pass the thread around the tension stud and pull it slightly to the right behind guide G. Draw the thread from the right through take-up lever 1 and pull it throu ...

  • Pfaff hobbymatic 800 - page 11

    Presser bar litter Lever 20 has three positions. G = The sewing foot is raised. (Before you remove the work, turn the balance wheel forward to raise the needle and take-up lever 1.) H = The sewing foot is lowered for sewing. = Darning position for the darning foot only. Position I is marked by a notch. E_ Drawing up the bobbin thread Hold the needl ...

  • Pfaff hobbymatic 800 - page 12

    8 Thread cutter (G) The thread cutter is an oblique slot located at the back of the presser bar. Raise the sewing foot. Pull the work out of the machine toward the back. Draw the threads into the cutter slot and pull them downwards to cut them. Regulating the stitch length The stitch length is set at mark G on the stitch length control. The numbers ...

  • Pfaff hobbymatic 800 - page 13

    (CD < CD tT £ CD — o. OlD o. OlD CD’ CD 0 0 .. :3. (D’ 2. (CD (CD -. O.-uo —Z CD 0 7 m 000(DCD ;:y;; D. D_ CD — 5 CD 3 CD 3 CD 300 -, — — CD 0 (DCD0CD3 g CD 0D — ;:: 5. - 2. 2 c p -ä CD 00 P.. 03 0Ocl) CD CD g a CD D3 0 CD :3- cr< _40 QN o N a —1 t3- CD 0. T CD (0 0 — CD 0 CX) 0 00. = 0<D2. C, IG) II —:3 <DO) CD ...

  • Pfaff hobbymatic 800 - page 14

    Selecting utility stitches on models 802 to 807 The various utility stitches possible are indicated by black letters in the red sector of the stitch panel on the machine and explained on page 11. The utility- and stretch-stitch selector dial 5 should only be turned in a clockwise direction. Turn dial 5 until the letter corresponding to the stitch y ...

  • Pfaff hobbymatic 800 - page 15

    Utility stitches, models 802—807 A Straight stitch B Zigzag stitch C Elastic stItch D Blindstitch E Elastic decorative stitch F Shell-edge stitch Models 802 and 803 have utility stitches A to D. A Stretch stitches, models 806, 807 A Elastic triple straight stitch B Elastic triple zigzag stitch C Honeycomb stitch D Pullover stitch E Feather stitq ...

  • Pfaff hobbymatic 800 - page 16

    Upper tension (19) G = Setting mark. The normal tension setting is in the white range between 3 and 5. The higher the number, the tighter the tension. Lower tension H = Regulating screw. Turn it left for a looser tension, or right for a tighter tension. = Both tensions are correct. J = Upper tension too loose or lower tension too tight. K Lower ten ...

  • Pfaff hobbymatic 800 - page 17

    Changing the needle Raise the needle bar. Then hold the needle, loosen screw G and pull the needle out downwards. Insert a new System 130/705 H needle (with the flat side of its shank facing toward the back) and push it up as far as it will go. Then tighten screw G. Reverse sewing Push button 12. As long as you keep this button depressed, the machi ...

  • Pfaff hobbymatic 800 - page 18

    Changing the sewing foot To release the sewing foot push the red button G. When attaching a sewing foot make sure stud H enters slot I. Place the sewing foot under the sewing foot holder and hold it in place with your left hand. Lower presser bar lifter 20 and at the same time reposition the sewing foot so that stud H fits in slot I. Hole K and scr ...

  • Pfaff hobbymatic 800 - page 19

    Sewing feet G Normal sewing foot H Clear-VieW foot i Buttonhole foot J Hemmer foot (special accessory available from your Pfaff dealer) K Zipper foot L BlindstitCh foot M Darning foot N Guide M 93-03 5 960-91 N 98-802 422-00 98-694 404-00 93-031 91 1I5 ...

  • Pfaff hobbymatic 800 - page 20

    Special sewing feet G Zipper foot Insert the rear pin in groove I, and the front pin in groove J. The zipper foot can be adjusted sideways for stitching along the right or left zipper chain. H = Darning foot Raise the needle bar. Push bracket M toward the back and hold it there. Insert the pin of the foot in hole K and attach the foot so that it re ...

  • Pfaff hobbymatic 800 - page 21

    a) .0 E >, a) 0) 0 0) 0 a) .3 —a) (0.0 a) ‘U > 00) C1) 0) —: — Ct) CC) 0) > 0 .00) :5> — a) S.; - — tJ C = C - a) g a) = . .5 ci) (0 1) a) D ) C Z a).0 0 > CC) :3 0 > Q > C c” E 0 3—4i U) :5 03 CC) - ci :300 — o -C C o C’) :3 a)) a) :3 = >-. a) -— o’2 G) .c C .22-o g 5 CC) ‘— aS ‘2 ‘t) -0 C C ...

  • Pfaff hobbymatic 800 - page 22

    Fitting the detachable workplate on models 800, 802 and 806 The foot control receptacle of these models also serves as a detachable workplate. Turn the receptacle round and fit it to the machine so that its two haoks enter the two holes in the machine base. Press the workplate down a little after fitting. (Figs. G and H below left.) Fitting the det ...

  • Pfaff hobbymatic 800 - page 23

    Changing the light bulb Switch off the electric current to the machine. Pull out the plug. Tilt the machine back and turn it so that the top is in front of you. Push the light bulb up, turn it towards G and pull it out. Insert the new bulb so that its pins slide in slots I. Push it up and turn it towards H. (Fig. below, left.) Cleaning and oiling O ...

  • Pfaff hobbymatic 800 - page 24

    Trouble shooting Cause: 1. Machine skips stitches Needle not inserted correctly. Wrong needle used. Needle bent or blunt. Machine threaded improperly. Needle too thin for thread used. 2. Needle thread breaks For any of the above reasons. Thread tension too strong. Poor-quality or knotty thread used, or thread that has become too dry by excessive st ...

  • Pfaff hobbymatic 800 - page 25

    4 Kinks appear on top and bottom of material. 5. Machine feeds irregularly or not at all Lint has accumulated between tooth rows of feed dog. Feed dog dropped. (Reverse-feed control is at left.) 6. Machine works heavily Thread ends in hook raceway. 7. Machine does not start Motor is disengaged. Check upper and lower tensions. Use first-class thread ...

メーカー Pfaff カテゴリー Sewing Machine

Pfaff hobbymatic 800のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- hobbymatic 800の取扱説明書
- Pfaffの製品カード
- パンフレット
- またはPfaff hobbymatic 800の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pfaff hobbymatic 800の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pfaff hobbymatic 800の取り付け説明書、サービスマニュアル、簡易説明書、またはPfaff hobbymatic 800のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pfaff hobbymatic 800の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pfaff hobbymatic 800デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPfaff hobbymatic 800を使用するのを助ける技術的文書のことです。説明書は通常、全てのPfaff hobbymatic 800ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pfaffの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pfaff hobbymatic 800の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPfaff hobbymatic 800の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pfaff hobbymatic 800に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pfaff hobbymatic 800デバイスの基本機能を使うにあたってのヒント。 Pfaff hobbymatic 800のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pfaff hobbymatic 800に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPfaff hobbymatic 800のメーカー/サービスへの連絡先に関する情報。

Pfaff hobbymatic 800についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPfaff hobbymatic 800の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPfaff hobbymatic 800で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)