Peavey 800Sの取扱説明書

32ページ 0.37 mb
ダウンロード

ページに移動 of 32

Summary
  • Peavey 800S - page 1

    CS 800S Oper at ing Guide ® ...

  • Peavey 800S - page 2

    Intended to alert the user to the presence of uninsulated Òdangerous voltageÓ within the productÕs enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. ...

  • Peavey 800S - page 3

    CS ® 800S POWER AMPLIFIER OWNERS MANUAL Congratulations on y our purchase of the new CS ® 800S stereo power amplifier . This latest v ersion is the most advanced e v er , using state-of-the-ar t s witching power supply technology to deliv er high fidelity and roc k solid perf or mance in a two- rac k-space unit that weighs just under 23 pounds. T ...

  • Peavey 800S - page 4

    FRONT P ANEL DDT ™ ACTIVE LED (1) Illuminates when DDT ™ Compression is taking place. With the ENABLE/DEFEA T s witch in the DEFEA T position, the LED indicates when clipping distor tion is occurr ing. POWER LED (2) Illuminates when A C power is being supplied to the amp and the associated channel is oper ational. Illumination is delay ed sligh ...

  • Peavey 800S - page 5

    IEC MAINS POWER CONNECTOR (7) The CS ® 800S is fitted with a univ ersal IEC connector . Into this connector one should alwa ys inser t a heavy duty #14 A WG 3 conductor line cord with a conv entional A C plug with a ground pin. This line cord should be connected to an independent mains circuit capable of supporting at least 15 amps continuously or ...

  • Peavey 800S - page 6

    THE P1 OUTPUT MODULE (15) The standard output module shipped with each amplifier is called the P1 MODULE. It off ers both dual 1/4" jacks and 5-w a y binding post speaker outputs f or each channel. F or each channel, the outputs are in parallel, hence the speak er connection cables can be ter minated with 1/4" phone plugs, or banana plugs ...

  • Peavey 800S - page 7

    THE S2 OUTPUT MODULE The S2 output module off ers dual Speakon ® Quic k Connectors and a unique patching capability to wire these connectors to meet the par ticular appli- cation. The Speakon ® is a f our-wire connector with the connections labeled as 1+, 1-, 2+ and 2-. Depending upon the loudspeaker needs , these connections can be used in v ar ...

  • Peavey 800S - page 8

    THE S2 OUTPUT MODULE REAR VIEW - BRIDGE MODE (19) The f ollowing wiring allows the Speak ons to be the bridge outputs with both in parallel. Such an arrange- ment per mits two 8 ohm enclosures to be connected in parallel to the CS-S amp in Bridge Mode. In this case, the wiring is as f ollows: 1+ on both connectors wired to Channel A signal output; ...

  • Peavey 800S - page 9

    Inadequate cooling due to preheated air , a reduction of air flow caused by b lockage of the amplifier's inlet/outlet por ts, or s e v erely ov erloading the amp may cause the amplifier's thermal sensing system to temporarily shut down that par ticular channel. This will be indicated by the channel po wer LED on the front panel ceasing to ...

  • Peavey 800S - page 10

    ...

  • Peavey 800S - page 11

    MANUAL DEL PROPIET ARIO DEL AMPLIFICADOR DE POTENCIA CS ® 800S Lo f elicitamos por la compra del nue v o amplificador de potencia estereofónico CS ® 800S . Esta versión, la más reciente y a vanzada e xistente, utiliza la última palabra en tecnología de conm utación de estado sólido para brindar alta fidelidad y un sólido rendimiento en un ...

  • Peavey 800S - page 12

    • Eficaz diseño de filtr o de bajo costo, con baja EMI (interferencia electr omagnética) por conducción • T otalmente operacional hasta con 85 VCA de suministro de la red (v oltaje nominal de 110 V) y 170 VCA (v oltaje nominal de 220 V) Sin duda comprobará que nuestro CS 800S no es simplemente otro amplificador de potencia, sino el mejor am ...

  • Peavey 800S - page 13

    INTERRUPTOR DE MODO DDT ™ (8) Este interruptor se usa para activar (ENABLE) o an ular (DEFEA T) el compresor DDT ™ . INTERRUPTOR DE MODO (9) Este interruptor se usa para seleccionar los modos de operación STEREO (estéreo) o BRIDGE (puente). MODULO DE ENTRADA B1 (10) El módulo de entrada estándar que se en vía junto con el amplificador se d ...

  • Peavey 800S - page 14

    Independientemente del tipo de cone xiones a usar , la carga mínima de los alta voces en par alelo debe limitarse siempre a 2 Ω por canal o 4 Ω en el modo de puente para cualquier aplicación. En las aplicaciones de operación en f orma sostenida, es preferible operar con cargas de 4 Ω por canal u 8 Ω en modo de puente, debido al hecho de ...

  • Peavey 800S - page 15

    otros dos se “almacenan”. T enga a bien notar que ahora, ambos bor nes rojos están conectados a la salida del Canal A y ambos bor nes negros están conectados a la salida del Canal B . En consecuencia, para conectar altav oces adicionales en modo puente, se debe utilizar un par de bor nes rojo y negro , en lugar de conectar cr uzados ambos bor ...

  • Peavey 800S - page 16

    nominal de cada canal. En este caso , la potencia nominal del amplificador CS 800S es de 600 W ef por canal con 2 Ω . La potencia nominal en el modo de puente es de 1200 W ef con 4 Ω (carga mínima). La operación en el modo de puente se logra colocando el interruptor de modo en la posición “BRIDGE” (puente), conectando la carga entre los ...

  • Peavey 800S - page 17

    MERKMALE DES VERSTÄRKERS • Zwei Rac keinheiten hoch, wenig er als 43 cm Tiefe • Gewic ht unter 11 kg, Schaltnetzteil • Einstec kbare Eingangsmodule • Zwei XLR-Buchsen (symmetrisc h)/Klinkenbuc hsen (unsymmetrisch) mit Dur chschleifausgang pr o Kanal • Universelles Dreiwege-Über gangsmodul • Einstec kbare A usgangsmodule • Zwei Klink ...

  • Peavey 800S - page 18

    RÜCKPLA TTE Unterbrecher (6) Der CS ® 800S v erwendet einen Unterbrecher anstelle einer Netzsicherung. Dieser Unterbrecher soll den Strom zum digitalen Netzteil begrenzen und es dadurch v or Überhitzung und möglicher Beschädigung aufgr und eines F ehlerzustands im V erstär ker schütz en. Der A uslösestrom wurde sorgfältig gewählt, so daß ...

  • Peavey 800S - page 19

    Dieser quasi-symmetrische Schaltkreis funktionier t „automatisch“ und macht sich beim nor malen Betrieb nicht bemer kbar . Er kann nicht deaktivier t werden. Klinken-Durchschleifbuchse (14) Diese mit „thru“ bezeichnete Buchse befindet sich an jedem Kanal. Sie bietet eine sehr praktische Möglichkeit zum Herstellen v on Steckv erbindungen. W ...

  • Peavey 800S - page 20

    RÜCKSEITE des S2 AUSGANGSMODUL - ST ANDARD STEREO MODE (17) Die nachf olgende Speakon(r) V erdrahtung sieht wie f olgt aus: 1+ entspricht dem Output (Ausgang) des Channel Signals und 1- der Masse des Channel Chassis. Dies ist der de facto Standard der meisten Lautsprechersysteme im unteren und mittleren Bereich. Diese V erdrahtung erlaubt den Ansc ...

  • Peavey 800S - page 21

    sich an der Rückplatte . Die F rontplatte v erfügt über LED-Anzeigen für Betrieb und DDT -Aktivier ung, Empfindlichkeitsregler und ei nen Netzschalter . Industrielle und kommerzielle Installation Für kommerzielle und andere Einsätz e, wo Betrieb mit hoher Leistung über lange Zeit erf orderlich ist, sollte der CS 800S in einem 19-Zoll-EIA-Rac ...

  • Peavey 800S - page 22

    Da der Endv erstär ker CS 800S einen Unterbrecher als Überstromschutz einsetzt, spielt das DDT -K ompressionssystem bei längeren A uftritten eine noch wichtigere Rolle, da es Übersteuerung und Über lastung der einzelnen Kanäle v erhinder t. Dauerbetrieb bei Übersteuerung kann zum Auslösen des Unterbrechers führen, aber bei aktivier tem DDT ...

  • Peavey 800S - page 23

    • Conception avec filtre économique efficace ... faibles interférences électr omagnétiques par conduction • Opérationnel jusqu’à 85 VCA (US) ... 170 VCA (Expor t) Nous espérons qu’à v os yeux, le CS ® 800S ne sera pas seulement un autre ampli, mais que v ous le considérerez plutôt comme l’appareil le plus remarquable que v ous ...

  • Peavey 800S - page 24

    INTERRUPTEUR DE MODE (9) Cet interrupteur ser t à sélectionner le mode de f onctionnement STEREO ou BRIDGE (pont) MODULE D’ENTREE B1 (10) Le module d’entrée standard livré av ec chaque amplificateur s’appelle le MODULE B1. Sur chaque canal, il offre à la f ois l’entré e électronique XLR symétrique et l’entrée casque quasi-symétr ...

  • Peavey 800S - page 25

    VUE ARRIERE DU MODULE DE SORTIE P1 (16) Le schéma ci-dessus illustre le câblage du MODULE P1. Remarquez que celui-ci est à l’env ers. Il s’agit de la position recommandée pour reconnecter ce module ou tout autre module. Lorsque les connexions correctes des fiches à languettes de 6,3 mm (1/4 po .) sont eff ectuées, le module peut être piv ...

  • Peavey 800S - page 26

    26 sont connectées à la sor tie masse du canal B. Cette configuration nécessite deux ca valiers par canal soit quatre au total. Repor t ez- v ous toujours au diagramme et vérifiez vos conne xions. Les deux bor nes rouges sont connectées à la sor tie du canal A, et les deux bor nes noires sont connectées à la masse. Ainsi, chaque paire noir/ ...

  • Peavey 800S - page 27

    Compression DDT ™ Le système bre veté de compression DDT ™ de P ea ve y per met à l’ingénieur du son de maximiser les perf or mances de l’ensemble amplificateur/haut-parleurs en empêchant l’amplificateur d’av oir une marge insuffisante (écrêtage). Ce système de compression est activé par un circuit original qui détecte les sig ...

  • Peavey 800S - page 28

    28 NOTES: ...

  • Peavey 800S - page 29

    29 NOTES: ...

  • Peavey 800S - page 30

    PEA VEY ELECTRONICS CORPORA TION LIMITED W ARRANTY Effective Date: July 1, 1998 What This W arranty Covers Y our Peavey W arranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada. What This W arranty Does Not Cover The W arranty does not cover: (1) damage caused by accident, misuse, abuse ...

  • Peavey 800S - page 31

    IMPOR T ANT SAFETY INSTRUCTIONS W ARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . For example, near or in a bathtub, swimming pool, sink, wet bas ...

  • Peavey 800S - page 32

    SPEAKON ¨ IS A REGISTERED TRADEMARK OF NEUTRIK ¨ AG Peavey Electronics Corporation ¥ 71 1 A Street ¥ Meridian, MS 39301 (601) 483-5365Fax (601) 486-1278 ¥ www .peavey .com © 1998 Printed in U.S.A. 12/98 80304489 ...

メーカー Peavey カテゴリー Stereo Amplifier

Peavey 800Sのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 800Sの取扱説明書
- Peaveyの製品カード
- パンフレット
- またはPeavey 800Sの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Peavey 800Sの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Peavey 800Sの取り付け説明書、サービスマニュアル、簡易説明書、またはPeavey 800Sのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Peavey 800Sの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Peavey 800Sデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPeavey 800Sを使用するのを助ける技術的文書のことです。説明書は通常、全てのPeavey 800Sユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Peaveyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Peavey 800Sの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPeavey 800Sの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Peavey 800Sに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Peavey 800Sデバイスの基本機能を使うにあたってのヒント。 Peavey 800Sのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Peavey 800Sに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPeavey 800Sのメーカー/サービスへの連絡先に関する情報。

Peavey 800Sについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPeavey 800Sの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPeavey 800Sで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)