-
Heat Controller SMA 18 - page 1
Heat Controller , Inc. • 1900 Wellworth A ve. • Jackson, MI 49203 • (517)787-2100 • www .heatcontroller .com INST ALLA TION INSTR UCTIONS SMA/SMH 18/24 V ersion C Single Zone Ductless Mini-Split System A/C and Heat Pump ...
-
Heat Controller SMA 18 - page 2
SMA/SMH 18/2 4 INST ALLA TION INSTRUCTIONS Heat Contr oller , Inc. 1 Installation Manual for Single Zone Ductless Mini-Split • For correct installation, read this manual before starting the installation. Please save this manual in a safe place. • Only trained and qualied service personnel should install, repair or service air conditioning eq ...
-
Heat Controller SMA 18 - page 3
Heat Contr oller , Inc. INST ALLA TION INS TRUCTIONS SMA/SMH 18/2 4 2 Part No. Name of Part Quantity 1 Installation Plate 1 2 Anchor 8 3 Mounting Screw A (ST3.9x25-C-H) 8 4 Remote Controller 1 5 Remote Controller Holder 1 6 Mounting Screw B (ST2.9x10-C-H) 2 7 Refrigerant Pipe Liquid side o 1/4" (<24,000 Btu/h) o 3/8" (≥24,000Btu/h) G ...
-
Heat Controller SMA 18 - page 4
SMA/SMH 18/2 4 INST ALLA TION INS TRUCTIONS Heat Contr oller , Inc. 3 INDOOR UNIT INST ALLA TION 1. Mounting Installation Plate and creating a W all opening Installation Plate and its measurements (inches): 5 inches or more 5 inches or more 2. Creating a wall opening 1. Attach the installation plate A. B. C. A. B. Clearance: Clearance: Clearance: C ...
-
Heat Controller SMA 18 - page 5
Heat Contr oller , Inc. INST ALLA TION INS TRUCTIONS SMA/SMH 18/2 4 4 2. Line Set and Condensate Drain Line B. When extending the drain hose, insulate appropriately . 1. Condenstate Drain 2. Line Set • Connect the indoor unit rst, then the outdoor unit. Bend and arrange the piping carefully . • Do not allow the piping to loosen from the indo ...
-
Heat Controller SMA 18 - page 6
SMA/SMH 18/2 4 INST ALLA TION INS TRUCTIONS Heat Contr oller , Inc. 3. Indoor Unit Installation secured to lip at the back Place the upper lip at the back of the indoor unit onto the up - per hook of the installation plate. Move the indoor unit from side to side to see that is is secured onto the hook of the installation plate. Push the lower part ...
-
Heat Controller SMA 18 - page 7
Heat Contr oller , Inc. INST ALLA TION INS TRUCTIONS SMA/SMH 18/2 4 6 5. Connecting Cables C. Wrap cables not connected to terminals with electrical tape so that they will not touch any electrical components. B. A. Lift the panel, loosen the screw , then open the Electric Box Cover . ...
-
Heat Controller SMA 18 - page 8
SMA/SMH 18/2 4 INST ALLA TION INS TRUCTIONS Heat Contr oller , Inc. 7 6. Piping and W rapping A. For the left-hand and right-hand piping, remove the rear plate bushing from the left side of the rear plate. B. Wind the line set, drain hose and wiring with tape se - curely and evenly . Consult local and national electrical codes for proper routing an ...
-
Heat Controller SMA 18 - page 9
Heat Contr oller , Inc. INST ALLA TION INS TRUCTIONS SMA/SMH 18/2 4 8 OUTDOOR UNIT INST ALLA TION 1. Outdoor Installation Precaution • Install the outdoor unit on a rigid base to prevent noise and vibration. • Locate the air outlet direction where the discharged air is not blocked. Ensure there are no obstacles blocking the unit’s air ow . ...
-
Heat Controller SMA 18 - page 10
SMA/SMH 18/2 4 INST ALLA TION INS TRUCTIONS Heat Contr oller , Inc. 9 3. Refrigerant Piping Connection 1. Flaring 2. Tightening Connection .04 A. B. A. B. Excessive torque can break the are nut. Ensure the proper torque is adhered to in the chart below . Hand tighten the are nut and then tighten it with a spanner and torque wrench as shown. ...
-
Heat Controller SMA 18 - page 11
Heat Contr oller , Inc. INST ALLA TION INS TRUCTIONS SMA/SMH 18/2 4 10 4. Wiring Connection A. Use a dedicated circuit. Use HACR break sized per unit’s rating plate. Size wires according to minimum circuit ampacity shown on the unit’s rating plate. • Be sure to comply with local and national electri - cal codes while running the wire from the ...
-
Heat Controller SMA 18 - page 12
SMA/SMH 18/2 4 INST ALLA TION INS TRUCTIONS Heat Contr oller , Inc. 1 1 AIR PURGE AND TEST OPERA TION 1. Air Purge where L=Length • Open the valve stem until it hits against the stop. Do not try to open it further . • Securely tighten the valve stem cap with a spanner or wrench. • T orque the valve properly: Gas pipe side (0.38"): 23.5 N ...
-
Heat Controller SMA 18 - page 13
Heat Contr oller , Inc. INST ALLA TION INS TRUCTIONS SMA/SMH 18/2 4 12 2. Gas Leak Check 3. T est Operation soapy water . Make sure connections do not leak with leak detector or soapy water . A. Lo packed valve B. Hi packed valve C. End of indoor unit connection D. End of indoor unit connection T est the unit’s operation after completing gas leak ...
-
Heat Controller SMA 18 - page 14
04/2009 08/2010 ...
Heat Controller SMA 18についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHeat Controller SMA 18の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHeat Controller SMA 18で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。