-
Harbor Freight Tools 4815 - page 1
SOLAR P ANEL / MONO-CR YST AL Model 04815 / 12 W atts Model 91013 / 24 W atts Model 90860 / 50 W atts Model 90717 / 100 W atts INST ALLA TION AND OPERA TING INFORMA TION 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yr ight © 2004 by Harbor F reight T ools ® . All rights reser ved. No por t ...
-
Harbor Freight Tools 4815 - page 2
SKUs 04815, 91013, 90860, & 90717 Page 2 GENERAL SAFETY W ARNINGS AND PRECA UTIONS 1. KEEP W ORK AREA CLEAN AND DR Y . Cluttered, damp or wet work areas invite injuries. 2. KEEP CHILDREN A W A Y FR OM WORK AREA. Do not allow children to handle this product. 3. ST ORE IDLE EQUIPMENT . When not in use, tools and equipment should be stored in a dr ...
-
Harbor Freight Tools 4815 - page 3
SKUs 04815, 91013, 90860, & 90717 Page 3 6. Always wear ANSI approved splash-resistant safety goggles when working with tools and equipment. If working around batteries also wear acid resistant work glov es. Any spilled acid must be w ashed off immediately . 7. INDUSTRIAL APPLICA TIONS MUST FOLLO W OSHA REQUIREMENTS. 8. DO NO T O VERREA CH. K e ...
-
Harbor Freight Tools 4815 - page 4
SKUs 04815, 91013, 90860, & 90717 Page 4 UNP A CKING When unpacking, chec k to make sure all par ts shown on the P ar ts List (page 9) are included. If any par ts are missing or brok en, please call Harbor F reight T ools at the number shown on the cover of this manual as soon as possible. SPECIFIC PRODUCT W ARNINGS AND PRECA UTIONS 1. THIS PRO ...
-
Harbor Freight Tools 4815 - page 5
SKUs 04815, 91013, 90860, & 90717 Page 5 T o Mount The Solar P anel At An Angle: 1. NO TE: F or increased pic kup of solar energy , and to minimiz e the collection of debris on the Solar P anel, it is recommended that the Solar P anel be installed on the mount- ing surface at an angle. (See Figure C, next page.) 2 . In order to mount the Solar ...
-
Harbor Freight Tools 4815 - page 6
SKUs 04815, 91013, 90860, & 90717 Page 6 3. T o secure the tw o angle brac kets to the mounting surf ace, drill two 1/4” holes though the base of each angle brac ket. Then, dr ill f our 1/4” holes, appropriately spaced, through the mounting surface. Use four screws, lock-washers, and nuts (not provided). (See Figure C.) T o Connect The Sola ...
-
Harbor Freight Tools 4815 - page 7
SKUs 04815, 91013, 90860, & 90717 Page 7 TYPICAL SINGLE SOLAR P ANEL CONNECTION (12 VOL T): FIGURE D Some parts shown are not included-see Parts List, page 9. ...
-
Harbor Freight Tools 4815 - page 8
SKUs 04815, 91013, 90860, & 90717 Page 8 TYPICAL MUL TIPLE SOLAR P ANEL CONNECTION (12 VOL T): FIGURE E Some parts shown are not included- see Parts List, page 9. TYPICAL DU AL SOLAR P ANEL CONNECTION (24 VOL T): FIGURE F Some parts shown are not included- see Parts List, page 9. ...
-
Harbor Freight Tools 4815 - page 9
SKUs 04815, 91013, 90860, & 90717 Page 9 CLEANING AND MAINTENANCE 1. NO TE: Alwa ys disconnect the Solar P anel(s) from the electrical charge controller before performing any cleaning, inspection, or maintenance upon the unit(s). 2. With the Solar P anel(s) disconnected from the charge controller , per iodically clean the Solar P anel(s) with m ...
-
Harbor Freight Tools 4815 - page 10
SKUs 04815, 91013, 90860, & 90717 Page 10 ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and shown f or illustr ation purposes only , and are not a vailab le individually as replacement par ts. 1 2 3 5 6 NO TE: P ar t 4 -Alligator Clips- are only included with SKU 04815 and are not shown. ...
Harbor Freight Tools 4815についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHarbor Freight Tools 4815の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 4815で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。