Philips LBB 5800の取扱説明書

15ページ 0.17 mb
ダウンロード

ページに移動 of 15

Summary
  • Philips LBB 5800 - page 1

    Philips Communication & Security Systems INST ALLA TION INSTR UCTIONS 1 GENERAL INFORMATION For a detailed description of DP 6000 paging calls refer to Installation Instruction No. 63 for the High Performance Control Desk (LBB 5800). 1.1 Description Philips Personal Security System PS 6000 combines paging functions with portable alarm facilitie ...

  • Philips LBB 5800 - page 2

    During programming, the desk display will show the program information as it is entered. Use the DIRECT CALL key of the desk to select the correct FCP number (if more than one connected ) the PROGRAM key to enter the selected data and scroll on to the next command. If a call string is selected and the RESET key is pressed, this will allow you to ed ...

  • Philips LBB 5800 - page 3

    3 FCP PROGRAMMING 3.1 PS 6000 menu selection To enter the PS 6000 menu, OPEN THE DESK EDITOR, SELECT and PRESS key “A”as shown in para. 2.3 and observe the correct display indication. DISPLAY “PS menu” When the PS 6000 menu is opened, the following sub menus can be selected to program the FCP. KEYSTROKE SUB MENU C Communications/Initialisat ...

  • Philips LBB 5800 - page 4

    COMMMAND “3” - ALLOCATE ADDRESS DISPLAY SHOWS “GIVADR (1/0)” Keystroke “1” - Will give the connected uninitialised FCP the lowest free (unallocated) address automatically.(see also Command 4) After the keystroke the desk will return to the communication menu Eronneous keystokes will generate the error bleep and return to the “Comm. me ...

  • Philips LBB 5800 - page 5

    4.3 Address Status Changing within Command “4” (STA FCP NR.) Submenu: The following gives the correct key selections necessary to move from one status to another: FROM TO KEY IN FROM TO KEY IN “Present” “Allocate” 0 - 1 “Unalloc” “Present” 1 - 1 “Present” “Unalloc” 0 - 2 “Unalloc” “Allocate” 1 - 1 - 0 - 1 “Pres ...

  • Philips LBB 5800 - page 6

    5.3 EDITING THE ALARM CALL STRING The display will show “FCP Nr., Channel Nr., “a” and the call string (e.g. 0105a - - - - - - - - - -). The alarm call data can be edited using the hex. key pad (Address- 4 digits / Codinf -1 digit / Info - 5 digits). This call will be transmitted if: a) An internal relay is programmed. b) The alarm call is en ...

  • Philips LBB 5800 - page 7

    5.8 MANUAL ACKNOWLEDGE TIME The display will show “FCP Nr. and Channel Nr. followed by “ack. time” followed by the programmed time (e.g. 0105 ACK TIME - - - ) Enter the desired time from 000 - 254 seconds (The time may not be set to 255 seconds) Press the PROGRAM key. The display will show “Update?” A further PROGRAM keystroke will update ...

  • Philips LBB 5800 - page 8

    The display will now show “Sel. Chan. Nr”, select the channel to be edited (01 - 16) and the display will show the programmed auto scan status of the channel e.g. “e c xx a m yy - 1 - zz” Location = 1 2 3 4 5 6 7 Where e = auto scan enabled (or “d” for auto-scan disabled) c = codinf value for an auto scan with manual acknowledge (see ta ...

  • Philips LBB 5800 - page 9

    8.1 FUNCTION ASSIGNMENT The display will now show the current setting of the FCP e.g. Function position - 1 2 3 4 5 6 7 8 9 Display shows - “A I I S I I I xx y” (xx = FCP Nr. ; y = Relay Nr.) Enter the required status by keying in position Nr. 1 - 7, followed by keystrokes “0” or “1” Keystroke “0” inhibits the function and the displ ...

  • Philips LBB 5800 - page 10

    9. WIRING DETAILS X1 - 9-pin D-type socket for connection to the High Performance desk (LBB 5800) Pin No. Function 1 +12 V power supply from the desk (fused at 1 AT) 2 not connected 3 not connected 4 RS 422 serial int. B (extra 220 Ohm) 50 V 6 + 12 V power supply from the desk (fused 1 AT) 7 not connected 8 RS 422 serial int. A (extra 220 Ohm) 90 V ...

  • Philips LBB 5800 - page 11

    PS 6000 and DP 6000 SYSTEM WIRING Installation details of the various units in the PS 6000 system can be found in the relevant Installation Instructions:(see contents) INST ALLA TION INSTRUCTION 69 DP 6000 DIGIT AL P AGING SYSTEM Page 11/15 December 1997 1 16 1 16 1 16 1 16 1 16 1 16 1 16 PSU* PSU* PSU* 12 3 4 5 6 7 8 PSU* PSU* TX RX DESK Control d ...

  • Philips LBB 5800 - page 12

    DP 6000 DIGIT AL P AGING SYSTEM INST ALLA TION INSTRUCTION 69 December 1997 Page 12/15 Enter Light Menu Recall Alarm P Enter Light Menu Recall Alarm P Enter Light Menu Recall Alarm P Control Desk LBB 5800 RS 422 Cable Extended Systems Max. 32 Field Control P anel LBB 6005 Master Storage Rac ks LBB 6151/01. Max. 5 slav es LBB 6151/00? ...

  • Philips LBB 5800 - page 13

    INST ALLA TION INSTRUCTION 69 DP 6000 DIGIT AL P AGING SYSTEM Page 13/15 December 1997 TABLE 1 FCP DEFAULT VALUES FUNCTION DEFAULT VALUE FCP Address (not inialised) h “50” Relay 1, 2, 3, function assignment I I I I I I I Relay 1, 2, 3, delay time 30 seconds Relay 1, 2, 3, pulse time 00 (pulse inhibit) Relay 1, 2, 3, standby status energised Rel ...

  • Philips LBB 5800 - page 14

    DP 6000 DIGIT AL P AGING SYSTEM INST ALLA TION INSTRUCTION 69 December 1997 Page 14/15 TABLE 3 The codinf value transmitted by the PST during any kind of acknowledge/alarm call is assigned a particular status in the FCP. This TABLE lists the codinf digit and status of the each in the FCP. CODINF DIGIT FUNCTION 0 The alarm LED status is updated to ? ...

  • Philips LBB 5800 - page 15

    INST ALLA TION INSTRUCTION 69 DP 6000 DIGIT AL P AGING SYSTEM Page 15/15 December 1997 12 3 5 4 6 7 8 9 10 15 14 13 12 11 16 Key to symbols 1. Handset (LBB 5804 optional) : Can be use instead of the desk microphone and speaker 2. Display window : LCD to display 16 digit information 3. Power On indicator (LED) : Green 4. Transmission On indicator (L ...

メーカー Philips カテゴリー Home Security System

Philips LBB 5800のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LBB 5800の取扱説明書
- Philipsの製品カード
- パンフレット
- またはPhilips LBB 5800の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Philips LBB 5800の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Philips LBB 5800の取り付け説明書、サービスマニュアル、簡易説明書、またはPhilips LBB 5800のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Philips LBB 5800の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Philips LBB 5800デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPhilips LBB 5800を使用するのを助ける技術的文書のことです。説明書は通常、全てのPhilips LBB 5800ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Philipsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Philips LBB 5800の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPhilips LBB 5800の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Philips LBB 5800に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Philips LBB 5800デバイスの基本機能を使うにあたってのヒント。 Philips LBB 5800のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Philips LBB 5800に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPhilips LBB 5800のメーカー/サービスへの連絡先に関する情報。

Philips LBB 5800についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPhilips LBB 5800の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPhilips LBB 5800で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)