Wilton 3410の取扱説明書

30ページ 1.02 mb
ダウンロード

ページに移動 of 30

Summary
  • Wilton 3410 - page 1

    This Manual is Bookmarked Operating Instructions — Parts Manual 7 x 12 Cut-of f Band Saw Models: 3400/3410 WHM TOOL GRO UP , Inc. 2420 V ant age Drive Elgin, Illinois 60124 Part No. 9078201 Ph.: 800-274-6848 Revision B 05/07 www .wmhtoolgroup.com Copyright © 2007 WMH T ool Group 177339 ...

  • Wilton 3410 - page 2

    W arranty and Service WMH T ool Group, Inc., warrants every product it sells. If one of our tools needs service or repair , one of our Authorized Servi ce Centers located throughout the United S tates can give you quick service. In most cases, any of these WMH T ool Group Authorized Service Centers can authorize warranty repair , assist you in obt ...

  • Wilton 3410 - page 3

    3 T able of Content s Cover Page ..................................................................................................................... ..... 1 W arranty ............................................................................................................................... .2 T able of Contents ............................... ...

  • Wilton 3410 - page 4

    4 Cutting capacity Blade speeds Blade drive Motor Blade guides Blade size Blade wheels Dimensions (L WH) Weight Wet cutting p ackage General Specifications The Wilton Models 3400 and 3410 cut-off band saws are designed for high production cut-off work. Four cutting speeds and a hydraulic feed control allows the efficient cut- ting of virtually any ...

  • Wilton 3410 - page 5

    5 1. Always wear protective eye wear when operating machinery . Eye wear shall be impact resist ant, protective safety glasses with side shields which comply with ANSI Z87.1 specifications. Use of eye wear which does not comply with ANSI Z87.1 specifications could result in severe injury from breakage of eye protection. 2. Wear proper apparel. No l ...

  • Wilton 3410 - page 6

    6 close as possible to the work piece. 9. Always wear protective eye wear when operating, servicing or adjusting machinery . Eyewear shall be impact resistant, protective safety glasses with side shields complying with ANSI Z87.1 specifications. Use of eye wear which does not comply with ANSI Z87.1 specifications could result in severe injury from ...

  • Wilton 3410 - page 7

    7 Operating Instructions Using the vise The vise on the saw table has two jaws. The jaw closest to the right hand side of the table is the stationary jaw . This jaw is firmly secured to the table using its pivot and lock bolts. When making a straight cut the stationary jaw is at right angles to the saw blade. When making an angle cut, the stationar ...

  • Wilton 3410 - page 8

    8 eventually catch the thrust shaft and allow you to open or close the locking jaw at its new lead screw position. When you slide the jaw to a new position, you can see where the nearest lead screw groove is by looking through the slot above the lead screw . (See Figure 1 .) Changing the locking jaw location: 1. Lift the quick release handle. 2. Sl ...

  • Wilton 3410 - page 9

    9 Adjusting stationary jaw for high accuracy angle cutting: 1. Raise the saw arm to full height and lock it in position with the shut-off valve. 2. Open the vise to full width. 3. Loosen the pivot and lock bolts shown in Figure 1 . 4. Open the shut-off valve and lower the saw arm until it is at full horizontal position. 5. T ake a machinist's ...

  • Wilton 3410 - page 10

    10 Controlling the cut: Hydraulic feed control The weight of the saw arm typically provides all of the force needed to move the saw blade through the workpiece. In fact, if the full weight of the arm is allowed to make the cut, rapid blade wear and poor cutting accuracy will result. Therefore, a hydraulic feed control is provided which gives the op ...

  • Wilton 3410 - page 11

    11 Changing blade speeds The Models 3410 and 3400 are 4-speed cut-off saws. The dif ferent speeds are obtained by changing the position of the drive V-belt which connects the motor pulley to the drivewheel gearbox pulley . T o change blade speeds: 1. Disconnect the saw from its electrical power source to prevent any possibility of accidental motor ...

  • Wilton 3410 - page 12

    12 Right angle cuts -- single pieces of stock 1. Raise the saw arm to its full up, open position. 2. Pull up on the quick release handle on the locking vise jaw and slide the vise jaws apart. 3. Place the stock on the saw table, between the vise jaws. If the stock is long, support the stock with appropriate infeed and outfeed supports. 4. Pull up o ...

  • Wilton 3410 - page 13

    13 Figure 8: Placing workpieces in the vise ...

  • Wilton 3410 - page 14

    14 Maintenance Replacing blades 1. Disconnect the saw from its electrical power source to prevent accidental start-ups. 2. Raise the saw arm to its full vertical position and lock it in place using the quick shut off valve on the hydraulic control cylinder . 3. Lift the safety cover in the lower portion of the blade guard door by sliding it upward. ...

  • Wilton 3410 - page 15

    15 Blade alignment adjustments The blade can suffer from several out-of-adjustment conditions. These conditions are shown in Figure 10 . Figure 1 1: Nomenclature for blade guide assembly and its components Figure 10: Blade alignment fault conditions Establishing a reference surface for blade adjustment So long as major changes and adjustments to th ...

  • Wilton 3410 - page 16

    16 Replacing blade guide and support components All component parts are secured with nuts, bolts, washers, or snap rings. T o remove and replace any component, first remove the blade according to instruc- tions in Replacing blades . Then remove and replace the faulty component(s). The guide and support bearings are mounted on eccentric shafts to pe ...

  • Wilton 3410 - page 17

    17 Adjusting blade vertical: The blade guide bearing seat can rotate as needed to make the blade vertical to the saw table. Follow these instructions. 1. With the saw arm in horizontal position, put a machinists square on the table, and against the blade, as shown. The blade should be square (vertical) to the table. If not... 2. Slightly loosen the ...

  • Wilton 3410 - page 18

    18 Adjusting guide bearings There are eight side blade guide/support bearings. These bearings are installed in the bearing seat, and the seat is attached to the sliding adjustment bracket. These bearings are stacked, with two bearings on each adjustment eccentric. The width of each pair of stacked bearings is slightly less than the width of a blade ...

  • Wilton 3410 - page 19

    19 Replacing the drive wheel 1. Complete steps 1 through 6 in Replacing blades . 2. Remove the snap ring which secures the lower wheel to the gearbox output shaft. 3. Pull the wheel off of the gearbox output shaft using a suitable puller . 4. Inspection: Examine the wheel for damage on its drive edge, shoulder , or the shaft boss. Replace if any fa ...

  • Wilton 3410 - page 20

    20 Servicing the hydraulic control cylinder Over a long period of service the hydraulic control cylinder may need replacement of its internal seals. Use the following procedure. (See Figure 18 .) 1. Lower the arm to its horizontal position. 2. Remove the upper fasteners, lower set screw , and pin which secure the cylinder to the saw arm and saw bas ...

  • Wilton 3410 - page 21

    21 Machine Set-up The saw delivered to you has been adjusted at the factory . A number of test pieces have been cut using the saw to verify the accuracy of cutting. Therefore, the only set-up operations required before releasing the saw for service are spotting the saw and establishing the electrical connections to the motor . If ordered with the c ...

  • Wilton 3410 - page 22

    22 Installing the coolant kit 1. Install the baffle in the t ank so the pump is held at one end of the tank. 2. Put the tank and pump assembly in the flanges which hold it in the saw base. The pump should be at the saw motor end of the base. 3. Install the nozzle assembly in the fixture in the right- hand guide bearing bracket and secure it with th ...

  • Wilton 3410 - page 23

    23 T roubleshooting 1. Use more pressure to tighten vise. 2. Check stationary jaw pivot and lock bolts for tightness. 3. Check quick release handle nut for excessive tightness -- nut should be just tight enough to keep adjustable jaw from tilting when tightening. 4. If you are stacking multiple pieces in the vise, be sure all of the pieces are capt ...

  • Wilton 3410 - page 24

    24 1. Observe chip formation to be sure cutting is efficient. 1. Adjust guide bearings according to instruction in this manual. 1. Increase blade tension so blade does not slip on the wheels. 1. Move guide brackets until they just clear the workpiece while making a complete cut. 2. For small section pieces, be sure the blade is sharp and correctly ...

  • Wilton 3410 - page 25

    25 Replacement Parts This section provides exploded view illustrations that show the replacement parts for the Model 3400 and 3410 7-Inch x 12-Inch Horizontal Cut-Off Band Saw . Also provided are part s listings that provide part number and description. The item numbers shown on the illustration relate to the item number in the facing parts listing ...

  • Wilton 3410 - page 26

    26 Exploded View - Saw Head ...

  • Wilton 3410 - page 27

    27 50 5710551 Bearing pin 2 51 5710561 Eccentric shaft assy . 2 51-1 5517504 Center shaft assy . 2 52 5710571 Brush 1 53 5710581 Hex nut 3/8x24 4 54A 5710591 Oil plug 1 55 571061 1 Phillips screw 1/4x3/8 2 56 5710621 V ertical cutting plate 1 57 5710631 Blade adjustable sear - rear 1 58 5710641 Adjustable bracket bar - rear 1 59 5710651 SHCS 5/16x1 ...

  • Wilton 3410 - page 28

    28 Exploded View - Saw Base ...

  • Wilton 3410 - page 29

    29 Parts List - Saw Base Ref. no. Part no. Description Qty . Ref. no. Part no. Description Qty . 19 571021 1 S pring washer 3/8 2 20 5710221 HH screw 5/16x3/4 8 20-1 5517520 HH screw 5/16x1/2 6 68 5517521 Set screw 5/16x3/8 1 69 5710761 Handle 1 70 5710771 Nut 1 71 5710781 V ise screw 1 72 5710791 Spring 1 73 571081 1 Vise thrust shaft 1 74 5710821 ...

  • Wilton 3410 - page 30

    30 Parts List - Hydraulic Cylinder Ref. no. Part no. Description Qty . 1 5517547 Dust cover 1 2 5517548 Retaining ring 2 3 5517549 Oil-seal 1 4 5517550 Oil-piston 1 5 5517551 O-ring 1 6 5517552 Cylinder body 1 7 5517553 Oil pressure regulator 1 8 5517554 Oil duct 1 ...

メーカー Wilton カテゴリー Saw

Wilton 3410のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 3410の取扱説明書
- Wiltonの製品カード
- パンフレット
- またはWilton 3410の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Wilton 3410の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Wilton 3410の取り付け説明書、サービスマニュアル、簡易説明書、またはWilton 3410のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Wilton 3410の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Wilton 3410デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWilton 3410を使用するのを助ける技術的文書のことです。説明書は通常、全てのWilton 3410ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Wiltonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Wilton 3410の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWilton 3410の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Wilton 3410に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Wilton 3410デバイスの基本機能を使うにあたってのヒント。 Wilton 3410のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Wilton 3410に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWilton 3410のメーカー/サービスへの連絡先に関する情報。

Wilton 3410についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWilton 3410の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWilton 3410で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)