-
Troy-Bilt 24B-060F063 - page 1
Yard Vacuum Chipper/Shredder/ Vacuum/Hose Model Numbers 24B-060F063 24C-060F063 Oper ator’ s Man ual IMPOR T ANT : READ SAFETY R ULE S AND INSTR UCTIONS CAREFULL Y TR O Y-BIL T LLC P .O . BO X 361131 CLEVELAND , OHIO 44136-0019 Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved fores ...
-
Troy-Bilt 24B-060F063 - page 2
2 TABLE OF CONTENTS Content Page Important Safe Operation Practic es .. ............. ................ ............. ............. .......... 3 Assembling You r Yard Vacuum .............. ............. ................ ............. ................ . 5 Know Your Y ard Vacuum ............... ............ ................. ............. ............ ...
-
Troy-Bilt 24B-060F063 - page 3
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out import ant safety instructions whic h, if not followed, could endanger the person al safety and/or property of your self and others. Read and follow all instructions in this manual before atte mpting to operate this machine. Failur e to comply with these instructions ma ...
-
Troy-Bilt 24B-060F063 - page 4
4 i. Never store the machine or fuel containe r inside where th ere is an open flame, spar k, or pilot light (e.g. furn ace, wate r heater, space heater , clothes drye r, etc.) j. To reduce a fire hazard, keep machine free of grass, le aves, or ot her debr is build-up. Clean up oil or fuel spillage and remove any fuel soaked debris . k. Allow machi ...
-
Troy-Bilt 24B-060F063 - page 5
5 WARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, understand and follow the warnings and instruct ions in this manual and on the machine. NOTE: Not all safety labels may apply to your Yard Vacuum. SECTION 2: ASSEMBLING YOUR YARD VACUUM IMPORT ANT: This unit is shipped without gaso line or oil in the engine ...
-
Troy-Bilt 24B-060F063 - page 6
6 Attaching The Handle • Unfold the upper handle until it aligns with the lowe r handle. • Secure th e two hand les by ti ghtening th e wing nuts (carriage bolt s must be seated properly into the handle). See Figur e 1. • Remove the hairp in clips from the handle brackets on the Yard Vacu um and remove the carriage b olts and wing nut s from ...
-
Troy-Bilt 24B-060F063 - page 7
7 Attaching The Blower Chute (If Equipped) NOTE: The blower chute is an option al feature on some model yard va cuums. It is NOT standard eq uipment. If your unit is not equipped with a blower ch ute, contact Customer Support as instr ucted on page 2 for information rega rding price and availability. • Grasp blower ch ute with one hand and slide ...
-
Troy-Bilt 24B-060F063 - page 8
8 Chipper Chute Allow twigs and small bran ches up to 1 1/2” in diameter to be fed in to the impeller for chipping. Blower Chute (If Equipped) When attached to unit the blower chu te is used to blow or scatter yard waste such as leaves, pine needles, or small twigs across yard. Nozzle Height Adjustment Lever Used to adjust the nozzle gro und clea ...
-
Troy-Bilt 24B-060F063 - page 9
9 • Twist the t wo buttons on the back of the bag to unlock and emp ty contents. See F igure 7. • Hold bag hand le and bag clip while e mptying the contents. • Compress bag op ening and fold inner flap over opening. • Fold outer f lap over inner flap and insert buttons on the bag throug h metal outlets. • Twist the b uttons to lock bag. F ...
-
Troy-Bilt 24B-060F063 - page 10
10 Nozzle Height Adjustment The nozzle ca n be adj usted to an y six position s, ranging from 5/ 8” to 4 1/8” ground clearance . The nozzle height ha s to be adjusted acc ording to the conditions. Move the heigh t adjustment levers forward or backward to adjust th e nozzle upwards or downwards. Make sure bot h levers are in the same position. S ...
-
Troy-Bilt 24B-060F063 - page 11
11 Maintenance Engine Refer to the separate en gine manual for all engine maintenance instructions. • Check engine oil level before each use as instructed in the separ ate engi ne manual packed with your unit. Read and follow instructions carefully. • Clean air cleaner every 25 hours under normal conditions or once a seaso n. Clean ever y few h ...
-
Troy-Bilt 24B-060F063 - page 12
12 Figure 14 • Remove lock nut that secu res flail screen to the lower housing. The fla il screen does not have to be removed. Re fer to Figure 11. • Remove the hex bo lt, lock washer, and flat washer that secure the im peller assemb ly to the cranksh aft. See Figure 15. Figure 15 • Apply lubricant to the th reads of impeller removal tool and ...
-
Troy-Bilt 24B-060F063 - page 13
13 SECTION 6: TROUBLESHOOTING NOTE: For repairs be yond the minor adjustments liste d above, contact your nea rest authorized se rvice dealer. Prob lem Cause Remedy Engine fails to start 1. Spark plug wire disconnect ed. 2. Fuel tank em pty or stale fue l. 3. Throttle cont rol lever not in correct starting posit ion. 4. Choke not in CHOKE position. ...
-
Troy-Bilt 24B-060F063 - page 14
MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth be low is given by Troy-Bilt LLC with respect to new merchandise purch ased and used in the United States, its possessions an d territories. “Troy-Bilt” warrants this produc t against defects in material and workmanship for a pe riod of two (2) years commencing on the date ...
Troy-Bilt 24B-060F063についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもTroy-Bilt 24B-060F063の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTroy-Bilt 24B-060F063で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。