Arrow Plastic CL72-Aの取扱説明書

24ページ 0.5 mb
ダウンロード

ページに移動 of 24

Summary
  • Arrow Plastic CL72-A - page 1

    * Size rounded off to the nearest foot BUILDING DIMENSIONS CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES WHEN HANDLING METAL PARTS. 709021004 Model No. CL72-A Owner's ...

  • Arrow Plastic CL72-A - page 2

    2 Owner's Manual Bef ore beginning constr uction, chec k local building codes regarding f ootings, location and other requirements. Study and understand this owner's manual. Impor tant infor mation and helpful tips will make y our construction easier and more enjo y able . Assembly Instructions: Instructions are supplied in this manual an ...

  • Arrow Plastic CL72-A - page 3

    3 Selecting and Pr eparing Y our Site: Before assemb ly , y ou will want to decide on a location f or your b uilding. The best location is a le vel area with good dr ainage. •Allow enough working space for ease of moving parts into position during assembly. Be sure there will be enough space at entrance for doors to open fully and enough space ar ...

  • Arrow Plastic CL72-A - page 4

    4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your build- ing. •Practice caution with the tools b ...

  • Arrow Plastic CL72-A - page 5

    Finish: F or long lasting finish, per iodically clean and wax the e xter ior surface. T ouch- up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manuf acturer's recommendation. Roof: K eep roof clear of leav es and snow with long handled, soft-bristled broom. ...

  • Arrow Plastic CL72-A - page 6

    6 ACCESSORIES.... A6 WEB * Some drilling required to fit buildings without mid-wall bracing. Model No. SS404 • Makes 8" to 12" (20-30cm) wide shelves in any length. • Brackets, braces, hardware included. Lumber is not included. Model No. SS900-A • Grey color • 3 shelves • Holds up to 85 lbs. (38kg) (even weight distribution) Hea ...

  • Arrow Plastic CL72-A - page 7

    THIS P AGE WA S LEFT BLANK INTENTIONALL Y 7 ...

  • Arrow Plastic CL72-A - page 8

    THIS P AGE WA S LEFT BLANK INTENTIONALL Y 8 ...

  • Arrow Plastic CL72-A - page 9

    The Foundation For Y our Building 9 FRONT (DOOR) FRONT (DOOR) Foundation BJ09 Note: Finished Slab dimensions, with lumber removed. OPTION 1: W ood Platform If you decide to build your own foundation, be sure to select the appropriate materials. These are the recommended materials for your foundation: ● 2 x 4's (5cm x 10cm) Pressure Treated L ...

  • Arrow Plastic CL72-A - page 10

    It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring Down The Building Anchoring A10 Arrow Anchoring Kit: (Model No. AK100 or 68383) Recommended for use with the concrete foundation. Contains: Corner gussets, perimeter clips, hardware, 1/4" masonary drill bit ...

  • Arrow Plastic CL72-A - page 11

    11 66150 Screw Driver Holder (1) 66149 Tool Hook (5) 66462 Hasp (1) 66684 Spring Latch (1) 66183 Roof Trim Cap (4) 66463 Swivel Staple (1) 66714 #6-32x7/16" Flat Hd Bolt (16) 66646 Washer (164) (5 sheets of 40) 66645 #6-32x3/4" Screw (7) 66148 Cap Protector (14) 65004 #8Ax5/16" Screw (154) 65923 #8-32x3/8" Bolt (68) 65941 #6-32 ...

  • Arrow Plastic CL72-A - page 12

    Parts List BK12 12 Assembly P a r t P a r t Quantity Check K e y No . Number Description i n C a r to n List 1 8984 Side Floor F rame 2 2 9429 Ramp 1 3 9430 F ront/Rear Floor F rame 2 4 9431 Mid W all F rame 1 5 9432 Side W all Angle 2 6 9433 Roof Rafter 3 7 9434 Rear W all Angle 1 8 9435 Horizontal Door Brace 4 9 9436 Right Roof T rim 1 1 0 9437 L ...

  • Arrow Plastic CL72-A - page 13

    13 Assembly by Key No. BK13 ...

  • Arrow Plastic CL72-A - page 14

    S tep 1 BJ14 14 The door header reinforces the front wall and roof. It is made up of two pieces. 1 Positioning the door header as shown, attach a starter strip to head- er using four screws, where shown. ● P ar ts Needed F or ● Door Header Assembly ● ● ● ● ● 9440 Door Header (one) ● ● ● ● ● 9442 Starter Strip (one) STEP 1 94 ...

  • Arrow Plastic CL72-A - page 15

    S tep 2 BK15 15 STEP 7 ● P ar ts Needed F or ● Door Assembly ● ● ● ● ● 9435 Horizontal Door Brace (four) ● ● ● ● ● 9936 Right Door (one) ● ● ● ● ● 9937 Left Door (one) ● ● ● ● ● 66612 Astragal (one) ● ● ● ● ● 67732 Foam Board (two) ● ● ● ● ● 9942 Vertical Door Brace (two) The steps on ...

  • Arrow Plastic CL72-A - page 16

    16 S tep 3 BJ16 The floor frame at the front of building is made up of two pieces. Proceed as follows: 1 Center the ramp on top of the front floor frame. Join the frames by in- serting four screws. 2 Place the floor frames on the foun- dation. Assemble the four corners of the floor frame using two screws at each corner as shown. 3 Measure the floor ...

  • Arrow Plastic CL72-A - page 17

    17 S tep 4 BK17 NOTE The remainder of the building assembly requires many hours. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. Each screw and bolt in the wall re- quires a washer. 1 Position right & left front corner panels ...

  • Arrow Plastic CL72-A - page 18

    S tep 5 BJ18 18 The main frame pieces give rigidity to the front and rear walls. 1 Fasten the rear wall angle across the top of the rear wall using four screws. 2 Fasten the door header across the top of the front walls using two screws, where shown. ● P ar ts Needed F or ● Frames ● ● ● ● ● 9434 Rear Wall Angle (one) ● ● ● ● ? ...

  • Arrow Plastic CL72-A - page 19

    S tep 6 BK19 19 Each wall panel has a crimped rib on one side. The crimped rib should go under the rib of the panel that follows it. The rear header supports the rear wall and roof. 1 Fasten the wall panels at the top and bottom with screws. 2 Fasten overlapping ribs using two screws and a bolt with nut. 3 Positioning the rear header, with small fl ...

  • Arrow Plastic CL72-A - page 20

    20 S tep 7 BJ20 1 Lift and fasten a right and left gable, under rear header, to the right and left hand wall with four screws. Join gables to header in the rear corners, using a screw. 2 Position roof rafters across width of building, under rear header, with tab on top of door header. Fasten using two screws. ● P ar ts Needed F or ● Gables/Roof ...

  • Arrow Plastic CL72-A - page 21

    S tep 8 BK21 21 STEP 1 The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs. 1 Fasten a door jamb to the front corner panel with one bolt and nut as shown. 2 Fasten the top of the door jamb to the door header with two screws. Do the same for the bottom into frame. Repeat steps 1 through 2 ...

  • Arrow Plastic CL72-A - page 22

    S tep 9 BJ22 22 STEP 1 Each screw and bolt in the roof re- quire a washer. NOTE Measure the building diagonally again and make adjustments to make sure the building is square. This will make the roof panel fit better, and holes will align. 1 Position roof panel on top and fas- ten to rear header, roof rafters and gables using screws. 2 Attach the p ...

  • Arrow Plastic CL72-A - page 23

    23 S tep 10 BK23 Screw Driver Holder (1) 1 Fasten the mid wall frame across the middle of the rear wall using eight bolts and nuts. 2 Position a shelf inside mid wall frame and slide to the end of building. Fasten using bolts and nuts through panels. Repeat Step 2 for the opposite shelf. 3 Install remaining two shelves above the first two at the ho ...

  • Arrow Plastic CL72-A - page 24

    S tep 1 1 BK24 24 ● ● ● ● ● Right Door Assembly (one) ● ● ● ● ● Left Door Assembly (one) ● P ar ts Needed F or ● Door Installation CL72-A BK24 1 Position doors in corners of door opening as shown and fasten hinges with 7/16" flat head bolts and #6-32 hex nuts. NOTE Be sure the heads on hinge pins are all installed towar ...

メーカー Arrow Plastic カテゴリー Outdoor Storage

Arrow Plastic CL72-Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CL72-Aの取扱説明書
- Arrow Plasticの製品カード
- パンフレット
- またはArrow Plastic CL72-Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Arrow Plastic CL72-Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Arrow Plastic CL72-Aの取り付け説明書、サービスマニュアル、簡易説明書、またはArrow Plastic CL72-Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Arrow Plastic CL72-Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Arrow Plastic CL72-Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがArrow Plastic CL72-Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのArrow Plastic CL72-Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Arrow Plasticの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Arrow Plastic CL72-Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははArrow Plastic CL72-Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Arrow Plastic CL72-Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Arrow Plastic CL72-Aデバイスの基本機能を使うにあたってのヒント。 Arrow Plastic CL72-Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Arrow Plastic CL72-Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるArrow Plastic CL72-Aのメーカー/サービスへの連絡先に関する情報。

Arrow Plastic CL72-Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもArrow Plastic CL72-Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがArrow Plastic CL72-Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)