-
Bell'O PR-25 - page 1
PR-25 Real W ood Audio V ideo Cabinet ASSEMBL Y INSTRUCTIONS Patent Pending The real hardwoods used in Bell'O furniture are naturally beautiful. Some differences in wood grain are desirable and expected. Please use only high quality wood furniture polish to care for your cabinet. ...
-
Bell'O PR-25 - page 2
P ARTS LIST P ART DESCRIPTION QUANTITY A. CABINET TOP 1 PC B. LEFT SIDE SUPPOR T P ANEL 1 PC C. RIGHT SIDE SUPPOR T P ANEL 1 PC D. UPPER INTERIOR SHELF 1 PC E. MIDDLE INTERIOR SHELF 1 PC F . BOTTOM SHELF 1 PC G. T OP DOOR P ANEL 1 PC H. LOWER SHELF DIVIDER 2 PCS I. UPPER SHELF DIVIDERS 2 PCS J. CENTER SUPPORT LEG 1 PC 2 ...
-
Bell'O PR-25 - page 3
P ARTS LIST (Continued) P ART DESCRIPTION QUANTITY K1. UPPER BACK P ANEL 1 PC K2. LOWER BACK P ANEL 1 PC L. LOWER CABINET DOORS 2 PCS 1. CAM LOCK PIN 18 PCS 2. CAM LOCK 18 PCS 3. 30MM DOWEL 32 PCS 4. 03X12MM SCREW 33 PCS 5. 50MM DOWEL 4 PCS 6. LEFT DRA WER HINGE 1 PC 7. UPPER DOOR KNOB 2 PCS 3 ...
-
Bell'O PR-25 - page 4
FOR YOUR SAFETY , PLEASE FOLLOW THESE PRECAUTIONS: ! AL W A YS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT . ! BE CAREFUL WHEN MOVING THE ASSEMBLED FURNITURE AFTER THE SHEL VES AND DOORS HA VE BEEN INST ALLED, AND/OR WHEN THERE IS EQUIPMENT LOCA TED ON OR IN THE FURNITURE AS THIS MA Y CAUSE THE SHEL VES A ...
-
Bell'O PR-25 - page 5
ASSEMBL Y INSTRUCTIONS NOTE: 2 PEOPLE ARE RECOMMENDED T O ASSEMBLE THIS FURNITURE. THIS T ABLE IS CONSTRUCTED WITH REAL WOOD VENEER. T O A VOID DAMAGE DURING ASSEMBL Y , IT S HOULD BE ASSEMBLED ON A SOFT SURF ACE. 5 Fig. 1 1. PLACE the bottom shelf (F) on edge. PLACE four smaller dowels (3) into the holes in the top side of the bottom shelf as show ...
-
Bell'O PR-25 - page 6
Fig. 2 6 E F H 5 2. PLACE four larger dowels (5) half way through the lower middle shelf (E), and PLACE the ends of the dowels into the exposed edge of the divider (H) as shown in Fig. 2. ...
-
Bell'O PR-25 - page 7
7 Fig. 3 3. PLACE the second divider (H) over the exposed ends of the dowels (5) on the opposite side of the lower middle shelf (E) with the FRONT arrow facing the front of the shelf (the edge without the cut out slots) as shown in Fig. 3. H 5 E ...
-
Bell'O PR-25 - page 8
Fig. 4 8 4. Place four smaller dowels (3) into the holes on the exposed edge of the divider (H). Place the upper interior shelf (D) onto the dowels as shown. D H 3 ...
-
Bell'O PR-25 - page 9
9 H B 14 3 2 1 10 Fig. 5 5. PLACE the left cabinet side (B) on a soft surface with the levelling foot facing the rear as shown. A. SCREW two cam lock pins (1) into the upper and center cross frame, and three cam lock pins (1) into the bottom cross frame. INSERT two smaller dowels (3) into each of the cross frames. B. INSERT two cam locks (2) into t ...
-
Bell'O PR-25 - page 10
10 Fig. 6 6. Placement of the right cabinet side (C): A. SCREW two cam lock pins (1) into the upper and center cross frame, and three cam lock pins (1) into the bottom cross frame. INSERT two smaller dowels (3) into each of the cross frames. B. INSERT two cam locks (2) into the underside of each shelf panel (D), (E) and three cam locks into the und ...
-
Bell'O PR-25 - page 11
Fig. 7 11 I 3 7 7 8 G 8 D 4 6 9 4 7. CAREFULL Y TURN the partially assembled cabinet upright. A. SCREW the LEFT drop down door hinge (6) and RIGHT door hinge (9) into the interior sides of the cabinet using the small Philips head screws (4). NOTE: THE DOOR TENSION ON THE HINGES CAN BE ADJUSTED BY TURNING THE KNOB LOCA TED ON THE HINGE. B. INSERT fo ...
-
Bell'O PR-25 - page 12
12 Fig. 8 8. SCREW two cam lock pins (1) into the tops of the cabinet sides (B) and (C). A. PLACE two smaller dowels (3) into the tops of the cabinet sides, and the tops of the dividers (I). B. PLACE two cam locks (2) into the interior of each cabinet side. C. CAREFULL Y ALIGN the cabinet top panel (A) with the top of the cabinet sides and dividers ...
-
Bell'O PR-25 - page 13
13 Fig. 9 9. Working from the rear of the cabinet, SCREW two rear panels (K1) and (K2) to the cabinet using screws (4). NOTE: THE REAR P ANELS ARE MADE T O BE SNUG. DO NOT FORCE OR BEND THE P ANELS MORE THAN VER Y SLIGHTL Y IF NEEDED. K2 4 K1 ...
-
Bell'O PR-25 - page 14
14 10. SCREW the lower door hinges (12) to the interior of the cabinet using screws (1 1). A. A TT ACH the cabinet doors (L) to the hinges (12) using screws (1 1). B. A TT ACH the lower cabinet knobs (13) to the doors using screws (8). Fig. 10 8 13 13 8 11 11 L L 12 11 12 Ensure table is level by adjusting rear legs (J). This will also aide in leve ...
-
Bell'O PR-25 - page 15
15 Fig. 1 1: Aligning the Doors 1 1. ALIGN the doors by adjusting the screws on the insides of each hinge (1 1) using the supplied screwdriver tool as shown. ...
-
Bell'O PR-25 - page 16
Warranty One (1) Y ear Limited Warranty All Bell’O International products are warranted, with the exception of glass, to the original purchaser at the time of purchase and for a period of one (1) year thereafter . Glass is warranted to the original purchaser at the time of purchase and for a period of thirty (30) days thereafter . Warranty is onl ...
Bell'O PR-25についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもBell'O PR-25の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBell'O PR-25で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。