Sony SDX-250Vの取扱説明書

36ページ 0.32 mb
ダウンロード

ページに移動 of 36

Summary
  • Sony SDX-250V - page 1

    AIT Drive 2-546-777- 11 (1)  2004 Sony Corporation AIT-1 Turbo TAPE DRIVE SDX-450V AIT-E Turbo TAPE DRIVE SDX-250V User’s Guide ...

  • Sony SDX-250V - page 2

    2 This document contains proprietary information which is protected by copyright. All rights reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of Sony. The information contained in this document is subject to change without notice. SONY MAKES NO WARRANTY OF ANY KIND WIT ...

  • Sony SDX-250V - page 3

    3 IMPORTANT SAFEGUARDS For your protection, please read these safety instructions completely before operating the appliance, and keep this manual for future reference. Carefully observe all warnings, precautions and instructions on the appliance, or the one described in the operating instructions and adhere to them. USE Power Sources – This unit ...

  • Sony SDX-250V - page 4

    4 INSTALLATION Water and Moisture – Do not use power-line operated units near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Power-Cord Protection – Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against them, paying ...

  • Sony SDX-250V - page 5

    5 Contents Overview .................................................................................................................. 6 Introduction .............................................................................................................. 7 About AIT Drives ...................................................................... ...

  • Sony SDX-250V - page 6

    6 Overview The Sony SDX-450V and SDX-250V drives are high capacity data storage devices using Advanced Intelligent tape (AIT) technology. The SDX-450V and SDX-250V drives achieve high data reliability through Read-After- Write, an additional level of Error Correction Code, and other features. The Sony SDX-450V and SDX-250V drives store data on tape ...

  • Sony SDX-250V - page 7

    7 Introduction About AIT Drives The SDX-450V is an internal AIT drive unit that uses data cartridges conforming to the AIT-1 Turbo format. The SDX-250V is an internal AIT drive unit that uses data cartridges conforming to the AIT-E Turbo format. The SDX-450V supports AIT-E Turbo, AIT-1 Turbo and AIT-1 formats. The SDX-250V supports only AIT-E Turbo ...

  • Sony SDX-250V - page 8

    8 The AIT Drive Unit SDX-250V has the following features: • Supports reading and writing to data cartridges conforming to the AIT-E Turbo format. • The third-level error correction code guarantee high data reliability. • Data compression provides 52 gigabytes of storage on 98 m tape-length AIT-E Turbo data cartridge. *1 The native capacity is ...

  • Sony SDX-250V - page 9

    9 Precautions Installation Avoid placing the drive in a location subject to: – high humidity – high temperature – mechanical shock and vibration – direct sunlight * For details, see “Specifications” on page 29. Operation • Do not move the drive while it is operating. It may cause malfunction. • Avoid exposing the drive to sudden cha ...

  • Sony SDX-250V - page 10

    10 Useable Cartridges The SDX-450V can be used with data cartridges marked with the AIT-E Turbo, AIT-1 Turbo or AIT-1 logo. The SDX-250V can be used with data cartridges marked with the AIT-E Turbo logo. Note • Be sure to use only the cartridges designed specifically for AIT. • Do not use anything but AIT cartridges with this system, as doing s ...

  • Sony SDX-250V - page 11

    11 Installation SCSI Connection/Setting the SCSI ID SCSI 68pin Connector 5 V Power Connector 1 2 3 4 GND GND 12 V Disable Enable Parity Note : = = = CLOSED/Jumper Don’ t care OPEN/Jumper not installed Pa rity Disable No Connection SCSI ID 3 SCSI ID 2 SCSI ID 1 SCSI ID 0 Jumpers SCSI ID SCSI ID 0 1 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 2 1 0 P .D. N. ...

  • Sony SDX-250V - page 12

    12 Option Switches (DIP Switch) DIP Switch Positions Default ON OFF 12345678 1 Drive Mode (OFF) 2 Drive Mode (OFF) 3 Drive Mode (OFF) 4 Drive Mode (OFF) 5 Terminator Power (ON) 6 Periodic Cleaning Req (ON) 7 DC Control (1) (ON) 8 DC Control (2) (OFF) DIP Switch ...

  • Sony SDX-250V - page 13

    13 DR (Disaster Recovery * ) Mode ON OFF 12345678 * In Disaster Recovery Mode, the drive enters the DR Standby Mode 15 seconds after you insert a write-protected tape into the drive, and all the drive LED blink. If you restart the drive while the LED are blinking, it starts as a CD-ROM device. For details about the Disaster Recovery Mode, refer to ...

  • Sony SDX-250V - page 14

    14 Cleaning Request Mode Periodic cleaning requests can be enabled by a DIP switch. ON OFF 12345678 When switch 6 is ON, cleaning requests are enabled. When enabled, the “CLEANING REQUEST” LED on the front panel lights after every 100 hours of operation. When this LED lights, clean the drive with a head cleaning cartridge. Note To maintain the ...

  • Sony SDX-250V - page 15

    15 Mounting Holes For 3.5" Standard Height 155.0 0.5mm [6.10" 0.02"] 90.0 0.3mm [3.54" 0.01"] 60.0 0.3mm [2.36" 0.01"] 70.0 0.3mm [2.76" 0.01"] 31.0 0.3mm [1.22" 0.01"] 21.0 0.3mm [0.83" 0.01"] 41.2 0.5mm [1.62" 0.02"] 4.8 0.5mm [0.19" 0.02"] 6-M3 (depth 2.5mm [0.1 ...

  • Sony SDX-250V - page 16

    16 For 5.25" Half Height 79.2 0.3mm [3.12" 0.01"] 79.2 0.3mm [3.12" 0.01"] 47.5 0.3mm [1.87" 0.01"] 7.0mm [0.28"] 79.2 0.3mm [3.12" 0.01"] 47.5 0.3mm [1.87" 0.01"] 94.0 0.5mm [3.70" 0.02"] 21.8 0.5mm [0.86" 0.02"] 41.2 0.5mm [1.62" 0.02"] 9.9 0.5mm [0.39" ...

  • Sony SDX-250V - page 17

    17 Reconfiguring from 5.25" Model to 3.5" Model You can reconfigure the 5.25" model to the 3.5" model yourself. 1 Remove the 2 screws for each side rail. 2 Take the side rail off. Side Rail (L) Side Rail (R) ...

  • Sony SDX-250V - page 18

    18 Orientation 10 ° 10 ° 10 ° 10 ° 10 ° 10 ° 10 ° 10 ° ...

  • Sony SDX-250V - page 19

    19 Attaching and Removing the Dust Cover Attaching the Dust Cover 1 Align the dust cover’s hinge clips (one on each side) with the pins of the drive bezel. • The dust cover should be positioned so that the magnets * on the cover’s back face the drive bezel. * This magnet does not affect the tape of the cartridge. • Holding the dust cover at ...

  • Sony SDX-250V - page 20

    20 2 Press down at an angle on each side in turn until you hear the hinge clips click into place. Caution Do not press the dust cover in horizontally from the front. Doing so could cause the dust cover to break. 3 Close the dust cover. This completes attachment of the dust cover. ...

  • Sony SDX-250V - page 21

    21 Removing the Dust Cover 1 Open the dust cover. 2 Holding the dust cover at both corners, carefully raise the dust cover. The dust cover hinge clips and drive bezel pins uncouple. Note We recommend that you use the drive with the dust cover. ...

  • Sony SDX-250V - page 22

    22 Operation Location of 3 LEDs There are three LED indications (TAPE MOTION LED, CLEANING REQUEST LED, REPLACE TAPE LED) and an EJECT button on the front panel of the unit. Front Panel (for 3.5" Standard Height) TAP E MOTION CLEANING REQUEST REPLACE TAP E Advanced Intelligent Ta p e LED EJECT button LED Indication for Drive Status The LED ind ...

  • Sony SDX-250V - page 23

    23 Drive Operation Loading a Cartridge Note While setting the data cartridge, do not turn off the host computer. This may cause a malfunction or damage data. 1 Turn on the host computer. Check that the drive’s TAPE MOTION LED, CLEANING REQUEST LED and REPLACE TAPE LED go off. 2 Open the dust cover. 3 Set the AIT data cartridge orientation as show ...

  • Sony SDX-250V - page 24

    24 Unloading a Cartridge The cartridge can be removed from the SDX-450V and SDX-250V either in response to a SCSI Unload Command, or by pressing the EJECT bottom. By pressing EJECT button, the tape is rewound and the cartridge ejected from the slot. Write-protecting a Cartridge Cartridges can be write-protected by sliding the tab on the back of the ...

  • Sony SDX-250V - page 25

    25 Using a Cleaning Cartridge To keep the AIT drive in top condition, clean the head as needed using a head cleaning cartridge with the AIT logo. When the head needs cleaning, the CLEANING REQUEST indicator lights. How to Clean 1 Load the head cleaning cartridge (SDX1-CL) into the AIT drive. Cleaning starts automatically. 2 After about 15 seconds, ...

  • Sony SDX-250V - page 26

    26 Emergency Tape Removal Procedure 1 Remove the drive from the chassis or enclosure to allow access to the bottom of the drive. 2 Remove the drive’s top cover. 3 Locate the small opening in the bottom of the drive and insert the tip of a precision screwdriver so that the Loading motor shaft can be rotated. 4 Rotate the motor shaft clockwise to b ...

  • Sony SDX-250V - page 27

    27 Caution Stop rotating the motor shaft immediately, when the guide B gets to the area below the line C-C (This line is defined by 2 circular tape guide surfaces of the cartridge). Otherwise, the gear of the drive can be damaged. The Initial Position of the Threading Mechanism 5 Before the manual ejection procedure, tape slack must be removed in o ...

  • Sony SDX-250V - page 28

    28 Interface Implementation Supported SCSI Messages Abort Message Parity Error Bus Device Reset Message Reject Command Complete No Operation Disconnect Restore Pointers Extended Message Save Data Pointer – Synchronous Data Transfer Request – Wide Data Transfer Request Identify ( w/&w/o Disconnect ) Ignore Wide Residue Supported SCSI Command ...

  • Sony SDX-250V - page 29

    29 Mass SDX-450V SDX-250V 3.5" 740 g (26.1 oz.) 740 g (26.1 oz.) 5.25" 970 g (34.2 oz.) 970 g (34.2 oz.) Specifications Product Specifications Dimensions (not including bezel and protruding parts) 3.5" 5.25" Height 41.2 mm (1.62 in) 41.2 mm (1.62 in) Width 101.6 mm (4.0 in) 146.0 mm (5.75 in) Depth 155.0 mm (6.1 in) 155.0 mm (6. ...

  • Sony SDX-250V - page 30

    30 Power Requirements SDX-450V Voltage Max Ripple Current Typical Maximum 5 V +/– 5 % 100 mVp-p 1.1 A 1.4 A 12 V +/– 10 % 150 mVp-p 0.4 A 1.2 A SDX-250V Voltage Max Ripple Current Typical Maximum 5 V +/– 5 % 100 mVp-p 1.1 A 1.4 A 12 V +/– 10 % 150 mVp-p 0.4 A 1.2 A Air-cooling Requirement Surrounding temperature < 40 ˚C (104 ˚F) Clean ...

  • Sony SDX-250V - page 31

    31 Sony Contacts For further information, please contact: Sony Electronics Inc., Tape Storage Solutions (USA) URL: http://www.storagebysony.com Sony Corporation Electronic Devices Marketing Group, Product Marketing Div. Computer Peripherals Dept. Tape Streamer Section Osaki Gate City East Tower, 1-11-1, Osaki Shinagawa-ku, Tokyo, 141-0032 Japan TEL ...

  • Sony SDX-250V - page 32

    32 Sony Corporation of Hong Kong Ltd. Shanghai Rep. Office 44F., HSBC Tower, 101 Yin Cheng East Road, Pudong, New Area, Shanghai, P.R.C. Postcode 200120 TEL: 86-21-6841-3222 FAX: 86-21-6841-0280 Sony Brasil Ltda. Rua Inocéncio Tobias, 125-BlocoA, CEP01144-000, São Paulo -SP-Brasil TEL: (55) 11-3824-6586 to 6598 FAX: (55) 11-3611-9064 URL: http:// ...

  • Sony SDX-250V - page 33

    ...

  • Sony SDX-250V - page 34

    ...

  • Sony SDX-250V - page 35

    ...

  • Sony SDX-250V - page 36

    Printed on 100% rec y cled pape r . Printed in Japan Sony Corporation ...

メーカー Sony カテゴリー Computer Drive

Sony SDX-250Vのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SDX-250Vの取扱説明書
- Sonyの製品カード
- パンフレット
- またはSony SDX-250Vの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Sony SDX-250Vの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Sony SDX-250Vの取り付け説明書、サービスマニュアル、簡易説明書、またはSony SDX-250Vのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Sony SDX-250Vの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Sony SDX-250Vデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSony SDX-250Vを使用するのを助ける技術的文書のことです。説明書は通常、全てのSony SDX-250Vユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Sonyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Sony SDX-250Vの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSony SDX-250Vの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Sony SDX-250Vに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Sony SDX-250Vデバイスの基本機能を使うにあたってのヒント。 Sony SDX-250Vのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Sony SDX-250Vに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSony SDX-250Vのメーカー/サービスへの連絡先に関する情報。

Sony SDX-250Vについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSony SDX-250Vの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSony SDX-250Vで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)